WE-EF CFY259 User manual

Product Information / Surge Protection
As an option, this luminaire can also be fitted with a surge
protector of Type 2-3 (at the time of order). The technical
data can be found directly on the installed device. If the
surge protector has been triggered by an adverse event,
the luminaire is automatically disconnected from the
mains. In that case, the LED on the surge protector no
longer lights up.
For comprehensive protection of the luminaire against
lightning and electrical surges, primary (Type 1) and
secondary (Type 2) surge arrestors must be installed into
the power supply. We recommend a combination arrestor
(Type 1+2+3), which is installed in the control cabinet.
Safety Notice
The manufacturer is discharged from liability when damage
is caused by improper use or installation.
If any luminaire and/or accessory is subsequently modi-
fied, the persons responsible for the modification shall be
considered as manufacturer.
CFY_KTY_ZFY200_270422 / 006-1347
Technical specifications are subject to change.
© WE-EF 2022
we-ef.com
The technical planner/installer is responsible for the pro-
per selection, sizing and installation of the surge protection
modules that must be provided on site. Please note the
various protection levels for Class I and II, as well as the
applicable statutory provisions regarding surge protection.
Installation and maintenance may only be performed by a
qualified electrician.
WE-EF LIGHTING USA
Tel [phone]
[email protected]
WE-EF LIGHTING
Installation and
Maintenance Instructions for
Bollards
CFY200 Series
KTY200 Series
ZFY200 Series

for Luminaires with ø 7.09 for Luminaires with ø 9.45
CFY259 – 6 LED CFY259 – 2x6 LED
ø 240
685
ø 240
685
ø 240
1085
ø 240
1085
ø 7.09
23.6
2
ø 7.09
39.3
7
ZFY230 – H23.62 ZFY230 – H39.37
23.6
2
ø 9.45
39.3
7
ø 9.45
ZFY250 – H23.62 ZFY250 – H39.37
23.6
2
ø 7.09
39.3
7
ø 7.09
KTY234 – H23.62 KTY234 – H39.37
ø 9.45
26.9
7
ø 9.45
42.72
CFY259 – H26.97 CFY259 – H42.72
Bollards
IP66, IK10
16 AWG
ø 0.551 in
Light source
CFY259
6 LED 12W – 700 mA* / 18W –1050 mA*
2 x 6 LED 24W – 700 mA* / 36W – 1050 mA*
ZFY230 / ZFY250
LED-FT 12W – 350 mA*
LED-FT 17 W – 500 mA*
LED-FT 24W – 700 mA*
Class I, II, ta = 25°C
KTY234
3 LED 9W – 1050 mA*
3 LED 13W – 1400 mA*
6 LED 18W – 1050 mA*
6 LED 36W – 1400 mA*
* Nominal power, for latest data refer to
www.we-ef.com
Tools required
– Screwdriver TX25
– Screwdriver TX40
– Screwdriver Philips size 2
Mounting Accessories
Planted root – Galvanised steel.
ESV4 for KTY234 / ZFY230 300-0461 7.1 lb
ESV4 for CFY259 / ZFY250 300-0464 9.7 lb
– Screwdriver with blade 3x1
– 13 mm wrench
Optical Accessories**
IL-180 Cut-off shield for KTY234 114-9185
IL-180 Cut-off shield ZFY230 / ZFY250 117-0228
** please specify when ordering
Table 1
Connecting EK
ON/
OFF 0-10V Basic Advanced
L X X X X
N X X X X
* X X X X
D + – X – –
D – – X – –
L 2 – – X –
* not available in class II
Table 2
Torque
Screw Torque
M4 max. 2.0 Nm (17.7 in-lb)
M5 max. 4.0 Nm (35.4 in-lb)
M6 max. 6.0 Nm (53.1 in-lb)
M8 max. 15.0 Nm (132.8 in-lb)
M16 max. 100.0 Nm (885.1 in-lb)

Maintenance
Apart from cleaning the product’s exterior surfaces,
no special maintenance work is required. Do not
use high-pressure cleaners.
In case of component failure due to abnormal cir-
cumstances or at end of life, replacement must be
carried out by a suitable and trained professional.
Protect our environment: Discard used LEDs in
compliance with the most recent environmental
legislation.
Warning
Do not open luminaire while mains electrical
supply is switched on.
15 Nm
(132.8 in–lb)
fig. 1 fig. 2
fig. 3 fig. 4
15 Nm
(132.8 in–lb)
fig. 5 fig. 6