Welch Allyn 71114 User manual

Pilot
Light
F1 T.04L
Split-Bobbin
Step-Down
Transformer
Terminal
Block
Outside
of Battery
Handles
Plug
(According to
Model No.)
2.5 v. Or 3.5v.
Nickel Cadmium
Batteries
F2 T.04L
27
27
CIRCUIT DIAGRAM
SPECIFICATIONS
Model Numbers: 71114, 71116,71118, 71154, 71156, 71158
Power Cord - 0.75mm , 3 wire earthed cord, 3m. Long
Input...Class 1...220-250v. (Numbers 71114, 71116, 71118, 71154, 71156, 71158)
50-60 Hz., .04 Amp.
Output...Model Number 60713, 71500 for 71670 Rechargeable Battery Handles
(charging rate: 75 ma. for 71500 and 60713; 60 ma. for 71670)
Fuses...(F1 and F2)...40 ma. Time lag low breaking capacity, 250 V.
Leakage Current is less than 10 microamps from any exposed metal part when proper earth is used.
Weight - approximately 1.25 kg.
Dimension - Charger requires only 18.4 x 8.9 cm.
Optional Charger with specula holder requires 18.4 x 21.6 cm.
Transport/Storage - 40 F (-40 C) to 122 F (+50 C) 95% RH Max.
2
oo o o
DESK CHARGERS
Thank you for purchasing this convenient
charger for diagnostic instruments. The
specifications and maintenance instructions
contained in this pamphlet should be
followed to insure years of convenient service.
Manufactured in
compliance with EN60601-1
Numbers: 71114, 71116, 71118
71154, 71156, 71158
Listed Product
ETL Laboratories
4341 State Street Road
Skaneateles Falls, NY 13153-0220 U.S.A.
Pilot
Light
F1 T.04L
Split-Bobbin
Step-Down
Transformer
Terminal
Block
Outside
of Battery
Handles
Plug
(According to
Model No.)
2.5 v. Or 3.5v.
Nickel Cadmium
Batteries
F2 T.04L
27
27
CIRCUIT DIAGRAM
SPECIFICATIONS
Model Numbers: 71114, 71116,71118, 71154, 71156, 71158
Power Cord - 0.75mm , 3 wire earthed cord, 3m. Long
Input...Class 1...220-250v. (Numbers 71114, 71116, 71118, 71154, 71156, 71158)
50-60 Hz., .04 Amp.
Output...Model Number 60713, 71500 for 71670 Rechargeable Battery Handles
(charging rate: 75 ma. for 71500 and 60713; 60 ma. for 71670)
Fuses...(F1 and F2)...40 ma. Time lag low breaking capacity, 250 V.
Leakage Current is less than 10 microamps from any exposed metal part when proper earth is used.
Weight - approximately 1.25 kg.
Dimension - Charger requires only 18.4 x 8.9 cm.
Optional Charger with specula holder requires 18.4 x 21.6 cm.
Transport/Storage - 40 F (-40 C) to 122 F (+50 C) 95% RH Max.
2
oo o o
DESK CHARGERS
Thank you for purchasing this convenient
charger for diagnostic instruments. The
specifications and maintenance instructions
contained in this pamphlet should be
followed to insure years of convenient service.
Manufactured in
compliance with EN60601-1
Numbers: 71114, 71116, 71118
71154, 71156, 71158
Listed Product
ETL Laboratories
4341 State Street Road
Skaneateles Falls, NY 13153-0220 U.S.A.

15mfd
High Impedance Voltmeter
1000
15mfd
High Impedance Voltmeter
1000
OPERATING INSTRUCTIONS
SYMBOLS
By plugging into any 220-250 v., 50-60 Hz. AC outlet, the desk
charger is immediately ready for use. An indicator light shows
that the charger is plugged in and ready to charge either one
or two Numbers 60713, 71500, or 71670 battery handles.
By leaving the handles in the charger, fully-charged instruments
are always ready for use. Batteries cannot be over-charged.
A completely discharged battery handle can be fully charged
overnight.
Attention: Consult Manual
The mark on this device indicates that it has been tested to and conforms with the provisions
noted within the 93/42/EEC Medical Device Directive.
Authorized European Representative
European Regulatory Manager
Welch Allyn, LTD
Kells Road, Navan
County Mead
Republic of Ireland
Tel: [phone]
Fax: [phone]
CAUTION: NOT FOR USE IN THE PRESENCE OF FLAMMABLE ANESTHETICS.
MAINTENANCE
LEAKAGE CURRENT CHECK
EARTH CONTINUITY CHECK
CLEANING
Like any other piece of electrical equipment, periodic electrical inspections should be
performed by qualified personnel. We recommend that this equipment be inspected at
least every six months, more often if used under adverse conditions.
The leakage current from exposed metal parts, when a good earth connection is used, should be
less than 10 microamps. This equivalent to 9.5 mv in the following circuit.
The resistance measured from the earth pin of the plug of the bottom plate should be virtually zero.
Do try to sterilize. May be cleaned by wiping with a dry cloth. Do pour any liquids into the
charging wells.
For repairs by qualified personnel, contact your local Welch Allyn distributor.
not not
OPERATING INSTRUCTIONS
SYMBOLS
By plugging into any 220-250 v., 50-60 Hz. AC outlet, the desk
charger is immediately ready for use. An indicator light shows
that the charger is plugged in and ready to charge either one
or two Numbers 60713, 71500, or 71670 battery handles.
By leaving the handles in the charger, fully-charged instruments
are always ready for use. Batteries cannot be over-charged.
A completely discharged battery handle can be fully charged
overnight.
Attention: Consult Manual
The mark on this device indicates that it has been tested to and conforms with the provisions
noted within the 93/42/EEC Medical Device Directive.
Authorized European Representative
European Regulatory Manager
Welch Allyn, LTD
Kells Road, Navan
County Mead
Republic of Ireland
Tel: [phone]
Fax: [phone]
CAUTION: NOT FOR USE IN THE PRESENCE OF FLAMMABLE ANESTHETICS.
MAINTENANCE
LEAKAGE CURRENT CHECK
EARTH CONTINUITY CHECK
CLEANING
Like any other piece of electrical equipment, periodic electrical inspections should be
performed by qualified personnel. We recommend that this equipment be inspected at
least every six months, more often if used under adverse conditions.
The leakage current from exposed metal parts, when a good earth connection is used, should be
less than 10 microamps. This equivalent to 9.5 mv in the following circuit.
The resistance measured from the earth pin of the plug of the bottom plate should be virtually zero.
Do try to sterilize. May be cleaned by wiping with a dry cloth. Do pour any liquids into the
charging wells.
For repairs by qualified personnel, contact your local Welch Allyn distributor.
not not