Weldex WDB-5655VDN User manual

Digital Day & Night
IR Color Camera
설명서용 서
IR LED type
Without IR LED type
MANUAL

2
The lightning flash with an arrowhead symbol, within an
equilateral triangle is intended to alert the user to the
presence of un insulated Dangerous voltage within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (Servicing) instructions in the
literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
CAUTION: To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes

3
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time,
fire may be caused.
Do not install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in fire or other hazards.
■ Warning

4
1.Features
-------------------
5
2. Components
-------------------
6
3. Names and functions of parts
-------------------
6
4. Setup Menu Operation
-------------------
7
5. Troubleshooting
-------------------
18
6. Protocol Setting
-------------------
19
7. Specifications ------------------- 20
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that
corrode the electronic components.
It can damage the CCD.
It can cause malfunctions to occur.
It is one of the most important parts of
the camera. Be careful not to be stained by
fin
g
er
p
rint.
Severe lighting change or flicker can
cause the camera to work improperly.
It can cause the image quality to be
poor.
Only use the camera under conditions
where temperatures are between
-10°C and +50°C. Be especially
careful to provide ventilation when
o
p
eratin
g
under hi
g
h tem
p
eratures.
If it is exposed to radioactivity,
For heated CCD, it will be out of order.
■Precautions
■Contents

5
☺Horizontal Resolution 600 TV Lines
Clear image quality has been achieved by employing a SONY CCD with
410,000
(Effective) pixels, which provides a horizontal resolution of 600 TV lines.
☺DAY & NIGHT
This camera has a function that automatically selects the mode that is
appropriate for daytime or night-time conditions. The COLOR mode operates
in daytime conditions to provide optimum colors, and BW mode operates in
nighttime conditions to enhance the definition of the image.
☺Electronic IRIS
The electronic IRIS function enables continuous automatic control of the
shutter between 1/60~1/120,000 seconds.
☺PRIVACY Function
The PRIVACY function conceals the areas you do not wish to appear on the
screen.
☺CCVC (Camera Control Via Coaxial cable)
This is a remote control function that overlaps the coaxial cable (for a transfer
of the Video signal) with the control signal. In installation or repair, this helps
you control the communication controller (optional) without additional cabling.
* Coaxial controller (Option SCX-RD100).
☺High Sensitivity
The built-in high sensitivity SONY COLOR CCD enables a clear image even
in
0.3Lux (0.1Lux B/W) or as low as 0.0004Lux with SENS-UP.
☺DNR (Digital Noise Reduction)
The amount of low luminance noise has been significantly reduced, and the
signal-to-noise ratio (S/N ratio) as well as horizontal resolution has been
improved,
resulting in a clear and sharp image display even in the dark.
☺Controlled by OSD Menu
The camera can be controlled by selecting text displayed on the monitor
screen.
☺Additional Functions
Sens-up, Motion Detection, Mirror functions are also available.
1. Features

6
1) Cable Connection
2) OSD Control
① 3AXIS BRACKET
-Please loosen screws and fix tilted and panned position.
③ LENS : Vari-Focal Auto Iris Lens ( 6.0mm ~ 50mm )
③ OSD PCB
- SETUP button : Used for the menu display. This button can be used
to confirm settings after changing the value of the selected function or
current conditions.
- UP & DOWN buttons : Used for selecting items by moving the cursor
up or down on the menu screen.
- LEFT & RIGHT buttons : Used when changing item values, by
moving the cursor to the left or right on the menu screen
UP
DOWN
LEFT RIGHT
SET
2. Cable Connection & OSD Control

7
□USING ICONS IN THE MENU
◆(EXIT) Exits the menu setting. Before you exits the menu setting, select
SAVE to save your settings, or select QUIT to cancel.
◆(RET) Returns to the previous menu
◆(HOME) Returns to the main menu.
◆(SAVE) Used to save your settings of MASK AREA, PRIVACY ZONE
and more. Once you save your settings, they will remain even if you select
QUIT in the menu.
◆(DEL) Used to deletes your settings of MASK AREA, PRIVACY ZONE
and more. Once you delete your settings, they will not be restored even if
you select QUIT in the menu.
□OSD Menu Structure
MAIN MENU Description
CAMERA SET Camera related functions and data.
INTELLIGENCE Motion detection, and more.
PRIVACY ZONE Privacy related settings
OTHER SET Configure for Factory Defaults, and more.
COMMUNICATION Communication set.
SYSTEMINFO Displays the system information.
LANGUAGE Select a language on the OSD menu.
CAMERA SET Description
CAMERA ID ON/OFF, Make the camera ID and set the place. 54 characters.(2 line)
IRIS ALC (Video/DC)/ELC, Select lens and control the iris level. Setting the BLC function.
AGC(MOTION) Setting the Max Gain under the low light.
DNR Digital Noise Reduction fucntion
SHUTTER Set the shutter speed. (High shutter speed)
SENS-UP Set the shutter speed. (Slow shutter speed)
FLICKERLESS Shutter speed : NTSC(1/60 →1/100sec), PAL (1/50 →1/120sec)
DAY/NIGHT Day / Night Mode (COLOR/BW/AUTO/EXT), Level set.
WHITE BAL White Balance Mode (ATW1/ATW2/AWC/MANUAL)
DIGITALZOOM Digital Zoom ratio set (x1 ~ x10 : x0.1 step)
DETAIL Aperture gain set
V-SYNC Internal/Line lock mode set
AGC COLOR SUP Color suppression amount at the AGC function
REVERSE Horizontal/Vertical Reverse
POSI/NEGA Positive or Negative Video output set
PIP Picture In Picture at Digital Zoom operation
DIS Digital Image Stabilization set
INTELLIGENCE Description
MOTION Motion detection function
MASK AREA Set the motion detection exception area
DISPLAY Motion Detection display ON/OFF
SENSITIVITY Motion Detection sensitivity
RESOLUTION Motion Detection resolution
ALARM OUT Alarm out set
PRIVACY ZONE Description
PRIVACY SET Set the privacy zone
STYLE Set the privacy style (Mosaic, Color, etc)
OTHER SET Description
FACTORY
DEFAULTS Set the privacy zone
OSD COLOR OSD menu color set
3. Setup Menu Operation

8
□MAIN MENU
◆CAMERA SET
Configure Camera related functions and data.
◆INTELLIGENCE
You can configure the settings of motion detection and more.
◆PRIVACY ZONE
You can configure the privacy related settings.
◆OTHER SET
You can configure for Factory Defaults, and more.
◆COMMUNICATION
Configures the settings regarding the UART communication.
◆SYSTEM INFO.
Displays the system information including the camera version and
communication settings.
◆LANGUAGE
Select a preferred one from the supported languages.
1) CAMERA SETUP
Setup the general functions of zoom camera module. Use the
▲▼◄►switch to select a menu item.
●CAMERA ID [OFF, ON]
The CAMERA ID menu is used for you to assign a unique name to a camera.
If you press the SET switch with the CAMERA ID menu selected, you will
see the appropriate screen. You can enter up to 54 alphanumeric or special
characters for the CAMERA ID. Select LOCATION and press the SET switch
to move the display position of the CAMERA ID.

9
●IRIS [ALC, ELC] The IRIS menu is used if you want to adjust the intensity
of radiation incoming to the camera.
●ALC (Automatic Light Control)
①If you press the SET switch with an ALC based sub menu selected, you
will see the appropriate screen.
The LENS menu is used if you select a type of the AI lens. For normal
operation, you must select DC for a DC-type lens, and select VIDEO for a
VIDEO type lens.
The LEVEL menu is used to adjust the overall brightness, where “+” will
increase the brightness and “.” will decrease it.
If you set the②BACKLIGHT option to BLC, you will see a menu where you
can set the BLC area.
You can set the desired BLC zone by defining the size and location.
If you use an ordinary camera in a scene with an intensive back light, the
object will be displayed dark on the monitor affected by the back light. To
solve this problem, you can use the BLC (Back Light Compensation) function
to improve the sharpness of the image in such a high contrast scene.
●ELC (Electronic Light Control)
If you press th①e SET switch when the ELC sub menu is selected, the
corresponding screen appears. You can make the ELC (Electronic Light
Control) function active or not.
②In similar to ALC setting, you can specify the BLC area.

10
●AGC[OFF, VERYLOW, LOW, MID, HIGH, VERYHIGH, USER, FIX]
The AGC (Auto Gain Control) menu is used to set the AGC level of the
camera. When the AGC is active, the camera automatically increases the
sensitivity by amplifying the Video signal when the strength of the signal falls
below the normal value. If OFF or FIX mode is selected in the SENS-UP
menu, you can specify the AGC level. If you press the SET switch with a
USER sub menu selected, you will see the appropriate screen. In USER
mode, you can break down the level in 16 steps from VERY LOW to VERY
HIGH to your preference.
If you press the SET switch with a FIX sub menu selected, you will see the
appropriate screen. As a fixed value of the AGC gain is used in FIX mode,
you can select one of the 16 detailed levels from VERY LOW to VERY HIGH
before fixing it. FIX mode is not available if you set the BACKLIGHT
※Note:
- If the DAY/NIGHT menu of the CAMERA SET is set to AUTO, the AGC
menu will be deactivated.
- If FLICKERLESS is set to ON, the AGC FIX mode will be disabled.
●MOTION [S.SLOW, SLOW, NORM, FAST, F.FAST]
The MOTION menu is used to adjust the strength of the AGC level for a
control of the camera motion. This is available only if the SENS-UP menu is
set to AUTO. You can select one from S.SLOW, SLOW, NORM, FAST and
F.FAST for the AGC level. If you monitor a fast moving object in a low
contrast scene, select F.FAST while select S.SLOW for a hardly moving
object in the same lighting condition.
※Note:
- If the DAY/NIGHT menu of the CAMERA SET is set to AUTO, the MOTION
menu will be deactivated.
●DNR [OFF, LOW, MID, HIGH, USER (1~16)]
You can configure the DNR (Digital Noise Reduction) related settings.
Reduces the noise on the screen. This is especially useful for a severely
distorted screen. You can set the level if you set DNR to USER.