Weldex WDP-4608MXV User manual

Camera Cable Connections
■ The WDP-4608MXV is also POE (Power Over Ethernet)
compatible.
Alarm output
12V/24VDC
Power Supply
BNC
Phone Jack
Wire
Plug DC Jack
Milestone
VMS Laptop
Monitor
Speaker
Wire
IP Router
NVR Desktop
1. Install the ‘vlc-2.0.6-win32-weldex-
certification. exe’ executable file.
4. Uncheck the [Run VLC media player 2.0.6]
checkbox
5. Click on the [Finish] button to complete
the installation.
2. From the [Select the type of install]
dropdown menu, choose [custom].
3. Confirm the installation path and
click[Next] to start copying files to
the PC.
For more information, refer to the WDP-4608MXV User Operation Manual.
Rev. A
VLC Media Player 2.0.6[or Higher version] Setup
Network
WDP-4608MXV Quick Installation Guide
www.weldex.com / [email protected]
Tel : [phone][USA]
Tel : [phone][GERMANY]
Fax : [phone][GERMANY]
Ground
Blue wire
Green wire
Black wire
Sensor input
Installing the camera on a wall
1. Fix the case body on the wall by using Tapping Screws(BHT M4xL16).
2. Connect ethernet and accessory cables and arrange cable running not
to damage or squeeze them.
3. Pass the ethernet and power accessory cables through the hole you want
to pass them when mounting the main body on the case.
4. Assemble the Height-Strip Cover.
5. Fasten 4 screws by turning top plate clockwise.

③ Click Search on the IPScan window.
④ Click the row of the device you wish to configure.
⑤ Click the IP Setup icon.
⑥ Enter the admin’s password. default password is [admin]
⑦ If you want to change IP address, enter a valid IP address, Subnet mask, and Gateway.
⑧ You can select the IP service type such as DHCP, Static IP.
⑨ Click Apply icon and wait for 30 seconds.
⑩ Click Web Browser icon.
① Install the latest ‘IPScan software’ executable file.
IP Scan Software Setup
H.264, MJPEG Video Stream values can be configured
independently of each other.
WDP-4608MXV Quick Installation Guide
② Run the IP Scan shortcut icon on main screen.
Change the Camera’s Network settings
For more information, refer to the WDP-4608MXV User Operation Manual.
Rev. A
www.weldex.com / [email protected]
Tel : [phone][USA]
Tel : [phone][GERMANY]
Fax : [phone][GERMANY]
⑤ ⑩
⑥
③
⑪ You will be prompted to enter an username and password.
default username is [admin] and default password is [admin].
⑫ After a successful login, the WEB Viewer screen will be
displayed in your web browser.
Web Viewer Login
⑪
⑧
⑨

▪ Default Resolution : 1280x720
640x480, 800x480, 800x600, 1024x768,
1280x720, 1280x1024, 1920x1080
▪ Frame rate : 1 ~ 30
▪ Bit Rate Control : CBR / VBR
▪ Bit Rate : 2Mbps ~ 10Mbps
Default : 4Mbps
▪ GOP : 1 ~ 90 default 30
▪ Default Resolution : 1280x720
640x480, 800x480, 800x600, 1024x768,
1280x720, 1280x1024, 1920x1080
▪ Frame rate : 1 ~ 30
▪ MJPEG Quality : 5 ~ 95
Default : 75
H.264, MJPEG Video Stream values can be configured
independently of each other.
Access the IP Camera Setup page on Web Viewer
Maintenance Setup
Video Profile Setup
Use this page to perform firmware upgrade, import/export settings, restore factory
default and reboot the device.
For software download, refer to below website address.
https://downloads.weldex.com/index.php/category/2-ip
▪ Import Setup
Click on the [BROWSE] button and select the configuration file
[sysenv.cfg] from the connected PC.
Click [IMPORT] to apply the configuration file settings.
after a few seconds, the device will reboot.
▪ Upgrade Setup
Click [BROWSE] icon and select the firmware file as above picture.
Click [UPGRADE] icon to start the upgrade process.
The upgrade progress bar will display the status of the upgrade.
after a few minutes, the device will reboot.
After a successful upgrade, [Complete] message window will
pop-up.
Software Download
WDP-4608MXV Quick Installation Guide
For more information, refer to the WDP-4608MXV User Operation Manual.
Rev. A
www.weldex.com / [email protected]
Tel : [phone][USA]
Tel : [phone][GERMANY]
Fax : [phone][GERMANY]
H.264, MJPEG Video Stream values can be configured independently of each other.