Wellcare FE-5856 User manual

Hot & Cold Massage Gun
E209
Model Number FE-5856
USER MANUAL

2
2
Contents
03 Important Safety Instructions
07 Product Overview
08 Getting Started
09 Operation
11 Other Useful Information
12 Specifications

3
3
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
Read this manual thoroughly before first use, even if you are familiar with this
type of product. The safety precautions enclosed herein reduce the risk of fire,
electric shock and injury when correctly adhered to. Make sure you understand all
instructions and warnings. Keep the manual in a safe place for future reference,
along with any warranty information, your purchase receipt and the original
packaging carton. If you sell or transfer ownership of this product, pass on these
instructions to the new owner of the product.
Always follow basic safety precautions and accident prevention measures,
including the following:
Usage conditions and restrictions
• This product is intended for private use by adults only. It is not suitable for
commercial or trade use. Do not use it for anything other than its intended
purpose, and only use it as described in this manual.
• Only use the device:
- on a dry surface of the body over clothing by lightly pressing and moving across
the body for approximately 60 seconds per region.
- on the body's soft tissue, as desired, without producing pain or discomfort —
do not use it on the head or any hard or bony area of the body.
- with the supplied applicators — chose the applicator that provides the best
desired effect.
• Bruising can occur regardless of the control setting or pressure applied. Check
treated areas frequently and immediately stop using the device at the first sign of
pain or discomfort.
• Keep fingers, hair or any other body part away from the shaft and backside of the
applicator as pinching may occur.
• Never insert any objects into the ventilation holes of the product.
• This product is NOT intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Supervise children to ensure they do not play with the product. Close
supervision is necessary if the product is used by or near children.
• Do not expose the product to direct sunlight or place it near a heater or other
heat source. Do not use it outdoors.
• Only use the supplied applicators. Do not use any attachment that is not
supplied by the manufacturer.
• Do not use the product while driving, straight after a meal, when drunk, or if
there is risk that you might fall asleep.
Important Safety Instructions

4
4
Important Safety Instructions (Cont.)
Health matters
This product is a non-professional appliance designed to provide a soothing
massage. Do not use it as a substitute for medical attention.
• CAUTION: Consult your doctor prior to using this product:
- if you have any concerns regarding your health, or suffer from an illness that
may give you cause for concern
- if you are pregnant
- if you have a cardiac pacemaker, artificial joints or electronic implants
- if you suffer from one or more of the following illnesses and complaints:
circulation disorders, varicose veins, open wounds, bruises, broken skin,
inflammation of the veins.
• CAUTION: Do NOT use this product:
- to supplement or replace medical treatment — chronic complaints and
symptoms may be made worse
- on swollen or inflamed areas or skin eruptions
- if you suffer from any physical ailment that would limit your capacity to
operate the control
Care, cleaning and storage
• Before cleaning or maintaining the device, make sure it is disconnected from
the power socket.
• Only clean the housing with a soft, dry or slightly damp cloth. Do not use liquid
or aerosol cleaners. Do not use solvent or oil-based cleaners.
• Do not use chemical, steel wool or abrasive cleaners to clean the outside of the
massage seat as these chemicals may damage the finish.
• Store the appliance in a cool and dry indoor area, disconnected from the power
supply and out of direct sunlight. Before prolonged storage, apply charge to
bring the battery to about half charge. Prolonged storage of an empty battery
may damage the battery. During prolonged storage, we recommend you use
and recharge the appliance every three months.
• Do not use the product if it has been damaged or is not working properly.
• Do not attempt to repair, disassemble or modify the product; there are no user-
serviceable parts inside. In case of damage, contact our after sales support
centre.
• Improper installation or misuse may result in the risk of fire, electric shock and
injury. We accept no responsibility for any eventual injury or damage caused by
improper use or noncompliance with these instructions.
• Please dispose of the battery responsibly after the service life of the product.

5
5
Important Safety Instructions (Cont.)
Electrical safety (charging)
• WARNING: Only use the supplied charging cable to charge the appliance.
• Voltage: Before connecting, ensure that the electrical voltage and circuit
frequency correspond to those indicated on the rating label.
• Connection/disconnection: To connect the battery charger, insert the power
plug rmly into an appropriate mains socket. To disconnect, grip the power plug
rmly and remove it from the outlet, do not pull on the cord.
• Charging: When charging the appliance, place it on a at surface, away from
hot surfaces and close to a power point so no one trips over the cord. Do not
leave the appliance charging or operating unsupervised. Do not attempt to
use the device while it is being charged.
• Protect the power cord: Do not kink, strain or damage the charger's power
cord and protect it from sharp edges and heat. A damaged power cord must
be replaced by the manufacturer, an authorised service centre or similarly
qualified personnel in order to avoid a hazard. In case of damage, contact our
after sales support centre for advice.
• Protect from moisture: To protect against electric shock, do not immerse the
cord, plug or the device in water. Do not spill liquids into the device. Do not
allow water to enter the ventilation holes of the device. Ensure your hands are
dry before use.
DANGER - to reduce the risk of electric shock
• DO NOT reach for an appliance that has fallen into water. Unplug it immediately.
• DO NOT use while bathing or in a shower.
• DO NOT place or store the appliance where it can fall or be pulled into a tub or
sink.

6
6
WARNING - to reduce the risk of burns, electric shock, fire or injury
to persons
• An appliance should NEVER be left unattended when plugged in. Unplug from
outlet when not in use, and before putting on or taking off parts or attachments.
• DO NOT operate where aerosol (spray) products are being used or where
oxygen is being administered.
• DO NOT operate under a blanket or pillow. Excessive heating can occur and
cause fire, electric shock, or injury to persons.
• DO NOT carry this appliance by the supply cord or use cord as a handle.
• NEVER operate the appliance with the air openings blocked. Keep the air
openings free of lint, hair, and the like.
• NEVER operate on a soft surface such as a bed or couch where the air openings
may be blocked.
• Not recommended for use by people with diabetes.
• NEVER cover the appliance when it is in operation.
• DO NOT use this product for more than 15 minutes at a time.
• Extensive use could lead to the product’s excessive heating and shorter life.
Should this occur, discontinue use and allow the unit to cool before operating.
• DO NOT use this product before bed. The massage has a stimulating effect and
can delay sleep.
• NEVER use this product while in bed.
• This product should NEVER be used by any individual suffering from any
physical ailment that would limit the user’s capacity to operate the controls or
who has sensory deficiencies in the lower half of their body.
• NEVER use this product in automobiles.
• This appliance is intended for household use only.

7
7
Product Overview
Control Panel
Interchangeable
massage head
attachment
Control panel
A. Battery/power LED indicator
B. Cold massage mode
C. Massage on/off
D. Hot massage mode
E. USB-C port: insert the supplied USB charging
cable and the other end to a power source to
charge the device.
A B C D E

8
8
Getting Started
Before first use
• Unpack the product and accessories and ensure all parts of the product are
undamaged and in good working order. Keep the original packaging carton and
materials in a safe place. It will help prevent any damage if the product needs to
be transported in the future, and you can use it to store the product when it is
not in use. In the event that the packaging is to be disposed of, please recycle
all packaging materials where possible.
• Plastic wrapping can be a suffocation hazard for babies and young children,
so ensure all packaging materials are out of their reach and disposed of safely.
• Unwind the cord of the charging cable to its full length and inspect it for
damage. Do not use the product if any part is damaged or not working
properly. In case of damage, contact our after sales support line for advice.
• Read this manual to familiarise yourself with the product. Pay particular
attention to the safety instructions on the previous pages.
Charging the device
• Charge for 5 hours with the supplied USB charging cable before first use.
• The battery indicator on the device will flash during charging.
• Once the indicator stops flashing and lights up green, it indicates that the
device is now fully charged.
• When the battery is low, please charge the device again.
Battery indicator colour
• Green (4 lights are lit up) - battery is fully charged.
• Green (1 light is lit up) - battery is low.
• Green (1 light is flashing) - no battery - device will automatically turn off.
Only use the device:
- On a dry surface of the body, over clothing, by lightly pressing and moving across
the body for approximately 60 seconds per region
- On the body's soft tissue, as desired, without producing pain or discomfort — do
not use it on the head or any hard or bony area of the body
- With the supplied applicators — chose the one that provides the best effect.
Bruising can occur regardless of the control setting or pressure applied. Check
treated areas frequently and immediately stop using the device at the first sign of
pain or discomfort.

9
9
Operation
Interchangeable head attachments
• The device comes with 5 interchangeable head attachments. To change head
attachments, first make sure the device is switched off. Pull out the current
head attachment and insert the desired head attachment.
• Note: for the hot & cold massage head, align the vertical bar of the head onto
the piston notch (see below illustration).
A. Hot & Cold massage head - relaxing whole body
B. Cylindrical head - suitable for deep tissue
C. Spherical head - suitable for larger muscle groups
D. Flat head - suitable for chest, back and flat muscles with a wide surface area
E. U-Shaped head - suitable for neck and spine
• Attaching and detaching the hot & cold
massage head. Ensure the vertical bar of the
head is aligned to the piston notch.
Vertical bar
A
D E
BC
Piston notch

10
10
Using the device
• When the device is off, press any button on the control panel to display the
battery status. The battery/power LED indicator will light up corresponding to
the current battery status.
• Press and hold the button for 3 seconds to start the massage. The default
intensity is set to level 1. The battery/power LED indicator will light up blue.
Press the button again to increase the intensity to level 2, the LED indicator
will now light up purple. Press the again to increase the intensity to level 3,
the LED indicator will now light up red. To stop the massage and turn off the
device, press and hold the button for 3 seconds.
• Press and hold the button for 3 seconds to start the heat massage mode.
The default heat setting is set to level 1 (35°C). The battery/power LED indicator
will light up blue. Press the button again to increase the heat setting to level
2 (40°C), the LED indicator will now light up purple. Press the button again
to increase the heat setting to level 3 (45°C), the LED indicator will now light up
red. To stop the heat massage and turn off the device, press and hold the
button for 3 seconds.
• Press and hold the button for 3 seconds to start the cold massage mode.
The default cold setting is set to level 1 (20°C). The battery/power LED indicator
will light up blue. Press the button again to increase the cold setting to level
2 (15°C), the LED indicator will now light up purple. Press the button again
to increase the cold setting to level 3 (10°C), the LED indicator will now light up
purple. To stop the cold massage and turn off the device, press and hold the
button for 3 seconds.
Notes
• You can switch between the massage modes when the device is on by pressing
the / / buttons.
• For the hot and cold massage, the hot & cold massage head must be
attached, as the other massage heads do not support this function.

11
11
Troubleshooting
If the device does not work, check and ensure that it is fully charged Also check
and ensure that the massage head is properly inserted into the device. If all
connections are correct and the product is still not working, please call our after
sales support centre. Do not attempt to open and repair the product yourself.
Another reason for the device to switch off automatically are the in-built safety
features. One safety mechanism switches the motor off automatically after 15
minutes' continuous operation. Furthermore, an overheat protection mechanism
switches the motor off to prevent overheating after extended use. In such a case,
wait 30 minutes for the device to cool before reuse.
Cleaning and care
• Before cleaning the device, make sure it is disconnected from the charging
stand and power source.
• Use a soft, slightly damp sponge or cloth to wipe the device clean. Dry
thoroughly using a dry cloth.
• Do not immerse the device in water or liquid or allow it to become wet.
Storage
• After use, wipe the device clean with a damp cloth.
• Store the device and the interchangeable massage heads in the original box to
keep dust accumulation to a minimum.
Service and repair
• The product contains no user-serviceable parts. Do not attempt to take it
apart, repair or modify it.
• Do not operate the product if it is damaged or working abnormally. Contact
our after sales support centre if a service is required.
Other Useful Information
Compliance
This appliance has been fully tested and meets all requirements as set out by
standards AS/NZS 60335.2.32 for electrical safety.
The RCM Mark (Regulatory Compliance Mark) indicates that the product
complies with the relevant guidelines of the ACMA as well as corresponding
government requirements for the safety of electrical devices.
E209

12
12
Specifications
Battery capacity Li-ion 10.8V, 2500 mAh
Charging voltage and current 5V 2A
Max. power consumption 35W Max.
Amplitude 10mm
Speed modes Level 1: 1800RPM, Level 2: 2000RPM,
Level 3: 2300RPM
Temperature value Heating: Level 1: 35°C, Level 2: 40°C, Level 3: 45°C
Cooling: Level 1: 20°C, Level 2: 15°C, Level 3: 10°C
Charging time 5-6 hours
Working time 1.5-4 hours (working time varies on selected massage mode
and intensity level)
Auto timer 15 minutes
Weight (device only) 625 g
Dimensions (W x H x D) (mm) 156 x 151 x 59
Responsible disposal
WARNING! This product contains a rechargeable lithium-ion battery. Never throw
the appliance into a fire and do not subject it to high temperatures. There is a risk
of explosion!
At the end of its working life, do not throw this appliance out with your household
rubbish. Electrical and electronic products contain substances that can have
a detrimental effect on the environment and human health if disposed of
inappropriately.
Cut the power cord of the battery charger and remove the lithium-ion battery pack
from the appliance before disposal. Dispose of the appliance and the battery pack
responsibly, observing any local regulations regarding the disposal of consumer
goods and batteries. Contact your local authorities for advice on battery disposal
and recycling facilities for electrical consumer goods.
For Technical and Warranty Support
1300 886 649
tempo.org/support
Distributed by Tempo (Aust) Pty Ltd,
PO Box132, Frenchs Forest NSW 1640

13
13
Notes

14
14
Notes

15
15
Notes

16
Warranty returns
Should you for any reason need to return this product for a warranty
claim, make sure to include all accessories with the product.
Product does not work?
If you encounter problems with this product, or if it fails to perform
to your expectations, make sure to contact our After Sales Support
Centre on (AU) 1300 886 649 or (NZ) 0800 836 761 for advice.
Distributed by Tempo (Aust) Pty Ltd ABN 70 106 100 252
PO BOX 132 Frenchs Forest, Australia NSW 1640
Customer Helpline:
(AU) 1300 886 649 (NZ) 0800 836 761
Email: tempo.org/support