WELLTECH WellGate M1 User manual

WellGate M1 Web User Guide
WellGate M1
(Single GSM gateway)
User Guide
Released Date : December-2014
Firmware Version : V.100

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
2 / 58 2014/12/1
Contents
1. Introduction........................................................................................................................4
2. Hardware Overview.........................................................................................................4
2.1 Two RJ-45 Network interface............................................................................4
2.2 One GSM SIM card interfaces..........................................................................4
2.3 LED Indications ......................................................................................................4
2.4 Rear Interface Descriptions...............................................................................4
3. Software Overview..........................................................................................................6
4. Instruction of Web Environment................................................................................7
4.1 Default setting........................................................................................................7
4.2 Network connection..............................................................................................7
4.3 Login VoIP Web page...........................................................................................7
4.4 VoIP main setting page.......................................................................................7
4.5 System Information..............................................................................................9
5. Phone..................................................................................................................................12
5.1 Dial Plan..................................................................................................................12
5.2 GSM setting ...........................................................................................................14
5.3 P2P Call Example.................................................................................................15
6. Network environment...................................................................................................16
6.1 WAN (network setting)......................................................................................16
6.2 DDNS........................................................................................................................18
6.3 VLAN.........................................................................................................................20
6.4 VPN (PPTP/L2TP connection) ..........................................................................21
6.5 NTP............................................................................................................................22
7. NAT ......................................................................................................................................25
7.1 LAN............................................................................................................................25
7.2 DMZ & MAC Clone...............................................................................................27
7.3 Virtual Server........................................................................................................28
8. SIP Setting........................................................................................................................29
8.1 Service (SIP register setting).........................................................................29
8.2 Codec........................................................................................................................30
8.3 Advanced................................................................................................................32
8.4 STUN (STUN & Froce configuration)............................................................37
9. Management (Advanced configuration)................................................................38
9.1 Status Log..............................................................................................................38
9.2 Auto Configuration..............................................................................................40
9.3 Auto Update...........................................................................................................42
9.4 New Firmware.......................................................................................................44
9.5 Advanced................................................................................................................45
9.6 Password.................................................................................................................47
9.7 Tones Setting ........................................................................................................50
9.8 Default.....................................................................................................................54
9.9 Language................................................................................................................55
10. Save & Reboot..............................................................................................................56
10.1 Function................................................................................................................56
10.2 Instruction ...........................................................................................................56

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
3 / 58 2014/12/1
11. Logout..............................................................................................................................57
11.1 Fuction...................................................................................................................57
11.2 Instruction ...........................................................................................................57

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
4 / 58 2014/12/1
1. Introduction
This user’s manual is ATA GSM system for ATA series GSM VoIP terminal adapter. This
user’s manual explains web configuration, and command line configuration for
WellGate M1. Before using this device, some setup procedures are required to make
the M1 GSM gateway work properly. Please refer to the “Instruction of Web
Environment” for further information.
2. Hardware Overview
The WellGate M1 GSM gateway has the following interfaces: Network, GSM SIM card
interface, LED indication, and power connector.
2.1 Two RJ-45 Network interface
These two interfaces support 10/100Mbps Fast Ethernet. You can connect WAN
RJ-45 Fast Ethernet port to the ADSL or Switch, and connect the LAN port to your
computer.
2.2 One GSM SIM card interfaces.
You can connect a GSM SIM card into the card try by pushing SIM card to lock. And
push SIM card again to eject SIM card.
2.3 LED Indications
There are three LED indicators on the GSM ATA to show the Power, GSM system, SIP
domain Register, WAN, and LAN status.
2.4 Rear Interface Descriptions
This is front panel printing and LED indications.
Item
Description
WellGate M1
Device model name.
Power
Power status. Power ON is light.
WAN
Shows device WAN port status. When WAN port connects
successfully, the LED will light up.
LAN
Shows device LAN port status. When LAN port connects
successfully, the LED will light up.
Status
Shows SIP domain account register status. When the SIP account
registed to SIP Server completely, the LED will light up. When this
device was used in P2P mode, this LED is OFF.
GSM
Shows SIM card of GSM gateway status if it connects to GSM Base
Station successfully. Once GSM gateway registered to GSM BTS
completely, the LED will light up.

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
5 / 58 2014/12/1
This is back panel connection port and indication.
Item
Description
Antenna
Antenna connector. Before using this GSM gateway, Please install
detachable Antenna at back panel. You can install dual bank
(1800/1900 MHz) shorter antenna, or quad band
(850/900/1800/1900 Mhz) longer antenna.
SIM Card Reader
Insert SIM card in tray. To remove SIM card from tray, simply press
SIM card to eject.
Reset
Reset to default by hardware. Press it and hold on 5 seconds then
release it. This device will run reset function and reboot by itself.
LAN
Connect personal computer.
WAN(PoE)
Connect ADSL or Cable Modem device. (If this device has PoE
feature, use this port to connect PoE switch.). Note: PoE is an
optional feature.
DC 9~12V
(Internal-Positive;
External-Negative)
Connect AC/DC power adaptor. Input voltage is 100 to 240 Vac.
Note. Please don’t remove the SIM Card from SIM Card reader when this device is still in
power on. Make sure to power off first before you remore SIM card. If you removed the
SIM Card and want to insert it in SIM Card reader again when power is ON, You need to
reboot the ATA_GSM device from its webpage configuration.

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
6 / 58 2014/12/1
3. Software Overview
Network Protocol Tone
•SIP v1 (RFC2543), v2 (RFC3261)
•IP/TCP/UDP/RTP/RTCP
•IP/ICMP/ARP/RARP/SNTP
•TFTP Client/DHCP Client/ PPPoE Client
•Telnet/HTTP Server
•DNS Client
•NAT/DHCP Server
•Ring Tone
•Ring Back Tone
•Dial Tone
•Busy Tone
•Programming Tone
GSM Function
Codec
•TX/RX Volume Adjustment
•SIM card PIN code PUK unlock
•Max call out time
•G.711: 64k bit/s (PCM)
•G.726: 16k / 24k / 32k / 40k bit/s (ADPCM)
•G.729A: 8k bit/s (CS-ACELP)
•G.729B: adds VAD & CNG to G.729
•G.723.1
•GSM
IPAssignment
•Static IP
•DHCP
•PPPoE
Voice Quality
•VAD: Voice activity detection
•CNG: Comfortable noise generator
•LEC: Line echo canceller
•Packet Loss Compensation
•Adaptive Jitter Buffer
Security
•HTTP 1.1 basic/digest authentication for Web setup
•MD5 for SIP authentication (RFC2069/ RFC 2617)
QoS
Call Function
•ToS field
•Call Forward
•Caller ID NAT Traversal
•STUN
Configuration
DTMF Function
•Web Browser
•Telnet
•In-Band DTMF
•RFC2833
•SIP Info Firmware Upgrade
SIPServer
•Registrar Server Account
•TFTP
•
HTTP

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
7 / 58 2014/12/1
4. Instruction of Web Environment
4.1 Default setting
4.1.1 Default network setting
Netwrok Mode: Default NAT Mode
WAN Port: DHCP Client Mode
LAN Port: DHCP Server Enable, IP Address: 192.168.123.1
4.1.2 Web login
VoIP Web Login default link, http://192.168.123.1:9999
Account Login :
Administrator: Login Account: root, Password: test
System: Login Account: system, Password: test
Normal: Login Account: user, Password: test
4.2 Network connection
Please connect PC Ethernet cable to LAN port, and set up PC to DHCP mode. Default IP
address is 192.168.123.150 at your computer.
4.3 Login VoIP Web page
Provide login system management page.
User Name
Input user’s name, it can be numeral or letters.
Password
Input password, it can be numeral or letters.
Login [button]
Login activate.
4.4 VoIP main setting page
4.4.1 Function instructions
Provide below function [Information (system information), Phone (phone environment),
Network (network environment), NAT (local network), SIP (SIP parameter setting),
Management (enhance setting), Save & Reboot , Logout ].

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
8 / 58 2014/12/1
4.4.2 Function descriptions
Item
Description
ATA GSM
Device type (WellGate M1).
Status
Current device information list table.
Phone
Provide GSM and Dial Plan function.
Network
Network setting provide [WAN , DDNS, VLAN , VPN (PPTP/L2TP),
NTP (Time sync)] function.
NAT
NAT provide [LAN, DMZ & Mac Clone, Virtual Server] function.
SIP
SIP provide [Service (SIP registeration), Codecs, Advanced,
STUN (STUN & Fource setting)] function.
Management
Management item provide [Status Log, Auto Provision, Auto
Update, Firmware, Advanced, Password, Tones, Default (reset to
default), Language] function.
Save & Reboot
Save and Reboot function.
Logout
Logout system.

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
9 / 58 2014/12/1
4.5 System Information
4.5.1 Function description
There are network information, firmware version, GSM register, and SIP register status.
Item
Description
WAN Information
Shows the current status of WAN Port.
Link Status
Shows the network connected Speed.
Active
Shows the network connected type.
IP Address
Shows IP address of the device.
Subnet Mask
Shows the subnet mask.
Default Gateway
Shows the default gateway.
Primary DNS
Shows the primary DNS server.
Second DNS
Shows the secondary DNS server.
MAC Address
Shows the MAC ID.
System
Information
Shows the status of System.
Model Name
Show device model name.
Version
Show device firmware version.
Firmware Version
Shows the firmware version for software control.
DSP Version
Shows the DSP version.
AC: AC97
WM: Winbound
LE: Legeeity
NV:Nuvoton
Current Time
Shows the current time.
Update Date
Shows the date of updating system.

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
10 / 58 2014/12/1
Item
Description
System Up Time
Shows the system running time.
Netwrk Link Up
Time
Shows the network running time.
SIM Card
information
Shows the SIM Card information.
Status
SIM Card status
No SIM Card : This device can’t detect SIM card or read SIM card
failed.
PIN Code Error : PIN code is wrong.
Registered : SIM Card connect GSM BTS network successfully.
Signal Strength
GSM signal strength which was detected by this device.
Reference GSM system standard.
Current Call Out
Time
Shows the GSM system connection running time.
Maximum Call
Out Time
The maximum outgoing call time limit.
Register
Information
Shows the status of SIP register.
Status
Shows register state.
Display Name
Shows register number.
4.5.2 System Information example
Figure 1: LAN Mode: Bridge (Ethernet Switch mode)
(Figure 1)

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
11 / 58 2014/12/1
Figure 2: LAN Mode: Router (NAT Router)
(Figure 2)

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
12 / 58 2014/12/1
5. Phone
This item provides GSM settings and Dial plan.
5.1 Dial Plan
5.1.1 Function description
Provide advanced Setting: Add number and Drop number or Speed Dial function rules.
5.1.2 Parameter description
Item
Description
Page
Default is 1. Select pages, Provide drop-down options: 1~5.
Total have five pages.
Index
Shows the serial number. There are 200 entries in total from
Phone 0~139. One page provides 40 entries.
Rule
Set up Add / Drop code or Speed Dial rules. User can enter
numbers or symbols (only support: 0~9, *, #, -, x, [, ], ; ).
Maximum length is 32 bytes.
Data format: PATTERN;PREFIX;DIALCUT; The “;” is entered as
location separator. It is always needed in this rule.
PATTERN:
Enter Add / Drop code or Speed Dial rules (only
support: 0~9, *, #, -, x, [, ], ; ); maximum length is 20 bytes.
When the dial number meet dialing rules field, user doesn’t need

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
13 / 58 2014/12/1
Item
Description
to dial end of dial [#] key. The device will dial the phone number
automatically.
PREFIX: Enter the phone numbers which you want to Add code,
(only support: 0~9, *, #), or keep null. The maximum length is
20 bytes.
DIALCUT: Enter the phone numbers which you want to to drop
code 『quantity』, (only support: 0~9), or keep null; maximum
length is 2 bytes.
Example 1: Rule: [2345679]xxxxxx;02;; .
Example 2: Rule: 800[0-9]xxxx;;;
Example 3: Rule: #88;0427121234;3;
Submit [Button]
Save the Settings.
5.1.3 Operate examples
Example 1: Index: 1, Rule: [2345679]xxxxxx;02;;
Step 1: In [Dial Plan Setting - Advanced] web page, Setup [Use Dial Plan: Advanced,
Index: 1, Rule: [2345679]xxxxxx;02;;] (See Figure 1).
(Figure 1)
Instruction 1: When dial number is [2+123456], Meet [Rule] field parameter
[2345679]xxxxxx rules, Stop to receive number immediately; Add prefix
code [02] before [2+123456] automatically. Actual sending number is
[02+2+123456] (See Figure 1).
Instruction 2: When dialing content [3+123456] at the beginning, Meet [Rule] field
[2345679]xxxxxx rules, Stop to receive number immediately. Add prefix
code [02] before [3+123456]. Actual sending number is [02+3+123456].
Example 2: Index: 2, Rule: 800[0-9]xxxx;;;
Step 1: In [Dial Plan Setting - Advanced] web page, Setup [Index: 2, Rule:
800[0-9]xxxx;;;] (See Figure 1).
Instruction 1: When dial number is [800+1+2345], Meet [Rule] field 800[0-9]xxxx rules,
Stop to receive number immediately. The device dials phone number
[800+1+2345] automatically.
Instruction 2: When dial number is [800+7+2345], Meet [Rule] field 800[0-9]xxxx rules,
Stop to receive number immediately. The device dials phone number
[800+7+2345] automatically.
Example 3: Index: 3, Rule: #88;0427121234;3;
Step 1: In [Dial Plan Setting - Advanced] web page, Set up [Index: 3, Rule:

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
14 / 58 2014/12/1
#88;0427121234;3;] (See Figure 2).
(Figure 2)
Instruction 1: When dialing number is [#88], Meet [Rule] field #88 rules, Stop to receive
number immediately. Delete 3 numbers (#88). Then add number [0427121234],
Actual sending number is [0427121234].
Example 4: Index: 4, Rule: #87;0427121234;2;
Step 1: In [Dial Plan Setting - Advanced] web page, Setup [Index: 4, Rule:
#87;0427121234;2;] (See Figure 2).
Instruction 1: When dialing number is [#87], meet [Rule] field #87 rules. Stop to
receive number immediately. Delete 2 numbers (#8). Then add prefix number
[0427121234] before [7]. Actual sending number is [0427121234+7].
5.2 GSM setting
5.2.1 Function
Provide GSM system parameter, Tx/Rx volume and call route forward.
5.2.2 Instructions
Item
Description
Tx Volume
Default is 8. Set up the size of the volume to hear the other side.
Provide options: 0 to 10.
Rx Gain
Default is 8. Set up the size of the volume to hear by caller.
Provide options: 0 to 10.
SIM Card PIN
Enter SIM card’s PIN code. This column can only enter numbers;

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
15 / 58 2014/12/1
Item
Description
Code
maximum length is 8 bytes.
Forward Number
Set up the GSM incoming call forward number. This column can
only enter numbers; maximum length is 16 bytes.
In P2P mode, please fill in receiver device IP address and port
number. For instance, 192.168.1.10:5060
In Proxy mode, please fill in SIP account number for SIP Server
or IP-PBX server to transit this call to remote receiver.
Maximum Call
Out Time
Default is 0. Shows maximum call out time. Set up outgoing call
time limit. The data range 0~6500 seconds. 0=No time Limit.
Current Call Out
Time
Shows outgoing call time already used.
Submit [button]
Save the configuration.
Reset Timer
[button]
Reset Current Call Out Time data.
5.3 P2P Call Example
Suppose there are one Wellgate M1 (IP: 192.168.1.2) and one ATA172plus (IP:
192.168.1.3) and ATA172plus SIP port is 5060. They are workin in P2P mode to call each
other. Here are configuration tips on both devices.
1. WellGate M1 has GSM incoming call to remote port 2 of ATA172plus via P2P call.
At GSM M1 gateway Forward Number configure at 192.168.1.3:5062. Since
ATA172plus SIP port is 5060 which is used for port1, port 2 uses 5062. If ATA172plus
SIP port is 8088, then port 2 SIP port should be 8090. When there is an GSM
incoming call at Wellgate M1, it will ring to port 2 of ATA172plus automatically.
2. ATA172plus wants to make a call to GSM network at 0933123456 via WellGate M1.
At ATA172plus, go to Phone book of webpage to configure. Put Name field as 301 and
Number field as 0933[email protected].1.2.
At WellGate M1 gateway, go to webpage: SIP Advanced Only Accept Trustred
Certificate Disable, to allow accepting P2P incoming call.
Dial 301 from ATA172plus will send this number 0933123456 to GSM network
automatically. ATA172plus has 140 records of phone book to be used for P2P call.
WellGate M1 only provides one-stage P2P outgoing call to GSM BTS network.

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
16 / 58 2014/12/1
6. Network environment
Provide [WAN, DDNS, VLAN, VPN, SNTP] function setting.
6.1 WAN (network setting)
6.1.1 Function
Provide WAN port configuration.
6.1.2 Instruction
Item
Description
Type
Default is DHCP Client and provides Fixed IP, DHCP (gains IP
Address automatically) and PPPoE: ADSL Dialing method.
IP Address
Current IP Address list or any IP Address (IPv4 format). If you
would like to change IP Address, please set up IP Type as “Fixed
IP” first. Maximum length is 15 digits.
Subnet Mask
Current Subnet list. A
subnetwork, or subnet, is a logically
visible subdivision of an IP network. The format is
xxx.xxx.xxx.xxx. Maximum length is 15 digits.
Default Gateway
Current default gateway list. Gateway is a node (a router) on a
TCP/IP network that serves as an access point to another
network. The format is xxx.xxx.xxx.xxx. Maximum length is 15
digits.
DNS Type
Default is Auto. Define DNS server mode to be Fixed and Auto.
Fixed: Manual set DNS server.
Auto: Network server provides DNS. It only supports in Type:
DHCP Client and PPPoE.
DNS Server1
Default: 168.95.192.1. It can be IP address or Domain Name.
Format: xxx.xxx.xxx.xxx. Maximum length is 15 digits.
DNS Server2
Default: 168.95.1.1. It can be IP address or Domain Name.
Format: xxx.xxx.xxx.xxx. Maximum length is 15 digits.
MAC ID
Display MAC address information.

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
17 / 58 2014/12/1
Item
Description
Host Name
Default: product name. Numbers or strings are both acceptable.
Length: 15 digits.
PPPoE User Name
Provides user’s name of PPPoE Server, it can be numbers or
strings. Length is 32 digits.
PPPoE Password
Provides password of PPPoE Server, it can be numbers or strings.
Length is 32 digits.
PPPoE Service
Name
Define Service Name; It can be IP address or Domain Name.
Length: 32 digits.
NOTE: This name is provided from ISP. If you don’
t know it,
please don’t change anything here.
PPPoE AC Name
Define AC Name; It can be IP address or Domain Name. Length:
32 digits.
NOTE: This name is provided from ISP. If you don’
t know it,
please don’t set anything here.
Submit [button]
Save the configuration.

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
18 / 58 2014/12/1
6.2 DDNS
6.2.1 Function
Dynamic DNS provides a residential user's Internet gateway that has a variable,
often changing IP address with a well known hostname resolvable through standard DNS
queries.
6.2.2 Instruction
Item
Description
Active
Default is Disable. The DDNS function will be enabled when you
set to Enable.
Host name
Enter Host name which can be IP Address or Domain Name.
Format: xxx.xxx.xxx.xxx. Length is 63 digits.
User Name
Enter user’s name for registering to DDNS Server.
Password
Enter the password. Maximum length is 63 digits.
E-mail address
Enter E-mail address. Maximum length is 63 digits.
DDNS Server List
Default is Disable; Configure your service provider here. Provide
option: User input, members.dyndns.rog and www.dtdns.com
mode.
DDNS Server
Enter DDNS Server which can be IP Address or Domain Name.
Format: xxx.xxx.xxx.xxx. Maximum length is 63 digits.
Type
Default is dyndns. Provide 3 options: dyndns, statdns and
customer mode.
Wild Card
Default is Enable. Provides 3 options: Enable, Disable and
Nochg.
NOTE: Please make sure your DDNS provider
supports this
feature when you set it to enable.
BACKMX
Default is Disable; The backup MX function will was activate
when you set it to enable. It provides two options: Disable and
Enable.
NOTE: Please make sure your DDNS provider supports this
feature when you set it to enable.
Off Line
Default is Disable. The Off Line function will be activate when

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
19 / 58 2014/12/1
Item
Description
you set it to enable. It provides two options: Disable and Enable.
NOTE: Please make sure your DDNS provider supports this
feature when you set it to enable.
Submit [button]
Save the configuration.

WellGate M1 Web user guide
Welltech Technology Co., Ltd.
20 / 58 2014/12/1
6.3 VLAN
6.3.1 Function
Provide Network, SIP and RTP VLAN function. This feature needs to work with VLAN
Router.
6.3.2 Instruction
Item
Description
Network (Both
WAN & LAN)
Configure VLAN function of both WAN and LAN ports.
VLAN Packets
Default is Disable. ATA supports VLAN function (accept VLAN
packets) when you set it to enable.
VID (802.1Q/
TAG)
Default: 136. Provide Virtual LAN ID (VLAN or VID) for VLAN
Server. Data range: 3~4097. Maximum length is 4 digits.
User Priority
(802.1P)
Default: 0. Set the user’s priority. Data range: 0 to 7.
SIP & RTP
Define SIP & RTP VLAN feature.
SIP VID
Default is 0 (disable). This feature is to define SIP VLAN ID.
Range is 3~4094. This feature is an independent one which do
not need to Enable [VLAN Packets] if you want to enable this
feature. Data length is 4 digits.
User Priority
(802.1P)
Default is 0 (disable). Define SIP package priority. Range is 0~7.
RTP VID
Default is 0 (disable). Define SIP VLAN ID. Range is 3~4094.
This feature is an independent one which do not need to Enable
[VLAN Packets] if you want to enable this feature. Data length is
4 digits.
User Priority
(802.1P)
Default is 0 (disable); Define RTP package priority. Range: 0~7
Submit [button]
Save the configuration.