WELLTECH Wellgate 26xx Series User manual

Wellgate 26xx Series
VoIP Gateway
User Manual
1. Introduction ...................................................................................................... 3
1.1 26xx Telephony Gateway.................................................................................. 3
1.2 Benefits .......................................................................................................... 3
1.3 Physical Interface............................................................................................. 3
1.4 Specification.................................................................................................... 4
1. Setting and maintenance..................................................................................
1.6 Environmental .................................................................................................
2. Appearance ....................................................................................................... 6
2.1 Front Panel: LED Indicators............................................................................ 6
2.2 Rear Panel: LED Indicators............................................................................. 8

26xx Technical Manual EN-V108
1
3. Environment Setup and IP Connection ................................................................ 9
3.1 Configuration................................................................................................... 9
3.2 Network Configuration ................................................................................... 12
3.2.1 WAN Setting ............................................................................................... 12
3.2.1.1 WAN Setting --Static IP.........................................................................................17
3.2.1.2 WAN Setting --DHCP............................................................................................18
3.2.1.3 WAN Setting --PPPoE ...........................................................................................19
3.2.2. LAN Setting ............................................................................................... 20
3.3 General configuration..................................................................................... 22
3.3.1 PABX Mode (Just use 2644 only).................................................................. 22
3.3.2.1 SIP Setting............................................................................................... 24
3.3.3 SIP Advanced Setting .................................................................................. 27
3.3.4 Payload Type Setting ................................................................................... 31
3.3. Line Setting ................................................................................................ 32
3.3.6 Qos Setting................................................................................................. 3
3.3.7 Speed Dial Setting....................................................................................... 37
3.3.8 Caller ID Setting ......................................................................................... 38
3.3.9 CDR Setting ................................................................................................ 40
3.3.10 Syslog Setting ........................................................................................... 42
3.4 Advanced Configuration ................................................................................. 44
3.4.1 System setting ............................................................................................ 44
3.4.2 SNTP Setting .............................................................................................. 49
3.4.3 Codec Setting ............................................................................................. 0
3.4.4 Voice Setting............................................................................................... 2
3.4. Tone Setting ............................................................................................... 4
3.4.6 Phone Setting ............................................................................................. 6
3.4.7 Digit Manipulation ....................................................................................... 8
3.4.8 Dial Plan..................................................................................................... 60
3.4.9 Call routing Editor ....................................................................................... 62
3. Management ................................................................................................. 64
3. .1 Provision Server .......................................................................................... 64
3. .2 Save-Reload setting..................................................................................... 67
3. .3 Voice File.................................................................................................... 68
3. .4 Upgrade Firmware....................................................................................... 69
3. . Reset to Default.......................................................................................... 70
3. .6 Network Status ........................................................................................... 71
3. .7 Version Info. ............................................................................................... 72
3. .8 Port Status ................................................................................................. 73

26xx Technical Manual EN-V108
2
3. .9 Password....................................................................... 錯誤
錯誤錯誤
錯誤! 尚未定義書籤
尚未定義書籤尚未定義書籤
尚未定義書籤。
。。
。
3. .10 Account .................................................................................................... 74
3.6 Rebooting the system .................................................................................... 7
Appendix A: How to set the P2P all ...................................................................76
Appendix B: How to use Http and Ftp provision............................................ 92

26xx Technical Manual EN-V108
3
1. Introduction
1.1 26xx Telephony ateway
The Wellgate 26xx is an 4 to 8-ports FXS/FXO VoIP gateway whi h in ludes
1-WAN/4-LAN 10/100 base-T NAT router to meet the urrent network
environment. Field-proven quality of Voi e ommuni ation and Fax transmission
over IP broadband a ess network to makes Wellgate 26xx series to be an
ex ellent solution for various VoIP appli ations.
1.2 Benefits
Ideally suited for Enterprise use, ri h-feature designed to inter-work with
IP-PBXs for small and middle enterprises.
Carrier-grade features are supported and tested to be fully interoperable with
leading Soft-Swit hes.
Provide CDR for all shop appli ation.
Superb devi e for apartment VoIP servi e.
1.3 Physical Interface
Ethernet port (RJ-45, 10/100 base-T)
1-WAN port, for onne t to router, ADSL modem (ATU-R), or swit h hub
dire tly.
4-LAN port, for PC or other network devi es onne ting.
Telephony port (RJ-11) --- depending on different models
8-FXS ports, to onne t with analog phone
8-FXO ports, to onne t with PSTN
4-FXO/4FXS ports, to onne t with PSTN and analog phone
4 FXO ports, to onne t with PSTN
4 FXS ports, to onne t with phone
Reset button (Fa tory Default)
AC power Ja k
Status indi ated LED
Indi ates Ethernet, FXS, and SIP system status

26xx Technical Manual EN-V108
4
1.4 Specification
IP Network onne tion
IPv4 (RFC 791)
MAC Address (IEEE 802.3)
PPPoE Client (RFC 2516)
DNS Client
DHCP Client (RFC 2131)
DHCP Server (RFC 2131)
NAT (RFC 1631)
TCP/UDP (RFC 793/768)
ICMP (RFC 792)
RTP/RTCP (RFC 1889/1890)
SNTP (RFC 2030)
TFTP Client
Telnet Server
HTTP Server
QoS – 802.1Q Virtual LANs
DiffServ (RFC 2475) / ToS (RFC 791/1349)
IP Telephony (VoIP)
SIPv2 (RFC 3261)
-Session Timer (RFC 4028)
-Priva y Me hanism (RFC 3323)
-Outbound proxy setting for in reasing performan e, produ tivity,
and se urity.
-SIP proxy redundan y- Support Primary and Se ondary proxy.
Voi e Code s
-G.711 (a-Law/u-Law): 64k bits (PCM)
-G.723.1: 6.3k/5.3k bits
-G.729A: 8k bits (CS-SCELP)
VAD – Voi e A tivity Dete tion with Silen e Suppression
CNG – Comfortable Noise Generation
E ho Can ellation (G.165/G.168)
Jitter Buffer – Adaptive & Configurable
Pa ket Loss ompensation - in reasing voi e quality
DTMF: In-band, Out-of-band (RFC 2833), and SIP-Info
Caller Generation/Dete tion – FSK, DTMF
FAX transmission

26xx Technical Manual EN-V108
5
-G.711 pass-through
-T.38 Fax relay proto ol
Tone Generation & Dete tion
-Ringing Tone
-Ring Ba k Tone
-Dial Tone
-Programming Tone
Call Features
-Call Hold
-Call Transfer (Blind & onsultant)
-Call Forward (Un onditional / No Answer / Busy)
MWI – Message Waiting Indi ation
PSTN Routing Prefix (2644 and 2644P use)
PSTN Bypass when network or system failure (2644 and 2644P use)
IP line hunting
Call Routing Plan
Digit Manipulation
Adjustable volume level
Se urity
HTTP 1.1 basi /digest authenti ation for WEB a ess
MD5 for SIP authenti ation (RFC 2069/2617)
Password prote ted Admin a ess authority
1.5 Setting and maintenance
Configure & Update method
-Web Browser (HTTP)
-Telnet
-FTP/TFTP
Setting parameter Import /Export
Voi e announ ement of IP address
Syslog Client – Debug & CDR (Call Detail Re ord)
1.6 Environmental
Dimension: 35 × 242 × 160 mm (Desktop)
Weight: 0.935kg (unit)
Operating Temp. & Humidity

26xx Technical Manual EN-V108
6
-Temp.: 0℃～45℃ (32℉～113℉)
-Humidity: 10％～85% relative humidity, non- ondensing
Storage Temp. & Humidity
-Temp.: 0℃～55℃ (32℉～131℉)
-Humidity: 10％～95％ relative humidity, non- ondensing
AC Power Adaptor:
-INPUT: AC100V-240V, 50/60Hz
-OUTPUT: DC 12V, 3.0A
Regulatory Complian e: FCC (Part 15, Class B) & CE
2. Appearance
2.1 Front Panel: LED Indicators
Wellgate 2608
Wellgate 2680
Wellgate 2644
Wellgate 2644P

26xx Technical Manual EN-V108
7
LED Des ription
Power When the power adapter is onne ted, the LED will light up
green.
Ready When system is startup su essfully, the LED will light up
green.
Proxy When the gateway is registered su essfully to a Proxy, this
will light up green.
WAN This will light up green when the gateway’s WAN port is
physi ally onne ted to the publi internet. When data is
transmitted through this port, it will flash green.
The default IP of WAN port is 10.1.1.3.
LAN (1-4) This will light up green when the gateway’s LAN port 1-4 is
physi ally onne ted to a lo al network (Refer to Rear Panel
se tion in page number for lo ation of LAN port 1-4). When
data is transmitted through this port, it will flash green.
The default IP of LAN port is 192.168.123.123.
T1-T8 The status LED for FXS port 1-8, this will light up amber
orange when the onne ted phone’s handset is lifted, or when
the onne ted phone is engaged in a onversation. It will
flash amber orange when there is an in oming all.
L1-L8 The status LED for FXO port 1-8. When there is no PSTN
onne ted, this LED will be ome blinking. When PSTN is
onne ted and no talking, the LED will be off. When a line is
using, the LED will be ome light up.

26xx Technical Manual EN-V108
8
2.2 Rear Panel: LED Indicators
Wellgate 2608
Wellgate 2680
Wellgate 2644 and 2644P
Item Des ription
Reset Press and hold over 5 se onds to reload fa tory default
setting, this will erase all the settings onfigured on the
gateway.
T1-T8 The RJ-11 FXS port 1-8, onne ts analog phone sets, trunk
line in PABX.
L1-L8 The RJ-11 FXO port 1-8, onne t to PSTN
T1/P1-T4/P4 It is a pair of FXO and FXS onne tor. The different is that the
when power off or appli ation is rashed, the FXO and FXS will
be onne ted together automati ally for lo al surviving.
LAN 1-4 10/100 Base-T RJ-45 so ket for LAN port 1-4, onne ts to
lo al area network.
WAN 10/100 Base-T RJ-45 so ket for WAN port, onne ts to wide
area network.
DC 12V The power so ket, input AC 100V~120V; output DC12V.3A

26xx Technical Manual EN-V108
9
3. Environment Setup and IP Connection
First of all, onne t your omputer to Wellgate 26xx’s LAN port by using DHCP.
The IP address assign to your omputer should be 192.168.123.x by default.
On e you an get the IP address from Wellgate 26xx, you an start the
onfiguration as below.
3.1 Configuration
Login to the WELLGATE 26XX web onfiguration menu
1. Open your WEB browser and key in the default IP address of the gateway
(http://192.168.123.123) in the Address box (see figure below).
3. You will see a pop-up window requesting username and password before you
an login to the web onfiguration menu. Username is “root” while password is
“root“(see figure below).

26xx Technical Manual EN-V108
10
2. You will enter the main page of the web onfiguration interfa e after you
keyed in the username and password orre tly (see figure below).

26xx Technical Manual EN-V108
11

26xx Technical Manual EN-V108
12
3.2 Network Configuration
The following instru tions will explain the onfigurations for setting up the WAN
port of the 26xx. There are in total three methods of onne tions: Stati IP,
DHCP and PPPoE.
Note: You an retrieve the IP address of the WAN port by keying #126 on the
phone set that is onne ted to the FXS port of the gateway. You will hear an IVR
announ ing the urrent IP address of the WAN port.
3.2.1 WAN Setting
The table shown below des ribes the onfiguration items for 3 onne tion types
of network (Stati IP, DHCP and PPPoE).

26xx Technical Manual EN-V108
13

26xx Technical Manual EN-V108
14
WAN Setting
Item Des ription Stati IP DHCP
PPPoE
Conne ted mode Sele t the onne tion method
for the WAN port of the 26xx,
you an hoose the following:
Stati IP
DHCP
PPPoE
V V V
Current IP Address Show urrent IP address V V V
DNS server mode Sele t the DNS behavior, you
an hoose the following:
Auto
Manual
“DNS auto” will retrieve the
DNS information sent from
the DHCP server.
“Manual” will look at the
spe ified Primary and
Se ondary DNS address.
V V V
Primary DNS address
Spe ify the address of the
Primary DNS. V V V
Se ondary DNS
address
Spe ify the address of the
Se ondary DNS. V V V
WAN Link Speed Sele t the onne tion speed
for the WAN port of the 26xx,
you an hoose the following:
Auto
100M
10M
V V V
HTTP port for WEB
management
Spe ify the port number for
WEB management, the
allowable range is 80,
1024~65535.
V V V
Remote A ess Web a ess for WAN port:
Disable: no any web a ess is
allowed
http: http a ess only
https: https a ess only
V V V

26xx Technical Manual EN-V108
15
both: http and https a ess
are allowed
HTTPS port for WEB
management
The http SSL port (the default
is 443), 1024~65535. V V V
IP address Spe ify the IP address. V
Subnet mask Spe ify the subnet mask. V

26xx Technical Manual EN-V108
16
WAN Setting
Item Des ription Stati IP DHCP
PPPoE
Default gateway Spe ify the IP address of the
default gateway. V
Remote a ess
restri tion
Restri ts/Blo ks users
onne ting to the WAN port’s
IP remotely, you an
Enable/Disable this option.
V V V
PPPoE userID Spe ify the username of the
PPPoE a ount V
PPPoE password Spe ify the password
asso iated to the PPPoE
a ount above.
V
Reboot after remote
host dis onne tion
When the remote host
(PPPoE) fails, the gateway
will retry 3 times to
re onne t, if there is no reply
from the remote host within 3
tries, then the gateway will
reboot. You an
Enable/Disable this option.
V

26xx Technical Manual EN-V108
17
3.2.1.1 WAN Setting --Static IP
1. Press the “Apply” button (at the bottom) after you finish to save hanges.
2. Press the “Reboot” button to apply the hanges.

26xx Technical Manual EN-V108
18
3.2.1.2 WAN Setting --DHCP
1. Press the “Apply” button (at the bottom) after you finish to save hanges.
2. Press the “Reboot” button to apply the hanges.
P.S. When you are using DHCP in WAN and WAN’s Ethernet able are not
onne ted, you will not able to a ess Wellgate by using WAN port if you
don’t know the DHCP IP address. In this ase, please onne t to LAN
port and a ess it.

26xx Technical Manual EN-V108
19
3.2.1.3 WAN Setting --PPPoE
1. Input PPPoE user ID and password
2. Press the “Apply” button (at the bottom) after you finish to save hanges.
3. Press the “CANCEL” button (next to the Apply button) to lear the values in
the page.
4. Press the “Reboot” button to apply the hanges.