Wenglor OPT2408 User manual

INTRODUCTION
UNpaCkINg
DesCRIpTION
This product is packed at the factory using suitable materials for safe transport. To open thepackage, do not use
any cutting blade to avoid damaging the product(s). Please use the delivered accessories ifneeded. (Donot use
any other products or equivalents to replace the delivered accessories). In the event of damage occurring during
shipping, itmust be reported to the carrier at time of delivery (including noting the damage in writing on the delivery
documents). It is also your responsibility to notify wenglorTPL in writing of the damage within 24 hours of receipt of
thepackage. Ifthese instructions are not followed, wenglorTPL reserves theright not to accept requests for return
and exchange of damaged products.
This accessory will WIDEN THE BEAM of your Bar light product.
References available:
nOPT2408 (AC-EBAR-N) : Narrow Beam, ±10°,
nOPT2409 (AC-EBAR-M) : Medium Beam, ±17°,
nOPT2410 (AC-EBAR-W) : Wide Beam, ±25°,
nOPT2411 (AC-EBAR-L) : Line light effect, ±9-16° elliptical,
nOPT2412 (AC-EBAR-N-P1) : Narrow Beam, ±10°, Polarised,
nOPT2413 (AC-EBAR-M-P1) : Medium Beam, ±17°, Polarised,
nOPT2414 (AC-EBAR-W-P1) : Wide Beam, ±25°, Polarised,
nOPT2415 (AC-EBAR-L-P1) : Line light effect, ±9-16° elliptical, Polarised,
nOPT2416 (AC-EBAR-POL1) : Polarised only,
nOPT2417 (AC-EBAR-T) : This is a transparent window. This has no effect on
the illumination angle. It is used to fill in spaces if you are creating multiple
illumination angles along the length of your bar light (eg. Curve effect).
NOTE:1 accessory per 125mm of bar light.
NOTE:This accessory only increase the angle of the light.
They cannot focus the light more than that provided by the embedded lens.
OpT2408
➔
2417
OpeRaTINg INsTRUCTIONs
This Technical User Guide contains warnings and guidance for correct and safe operation of the product. These
instructions must be followed at all times. wenglorTPL will not be held responsible for problems caused by using
theproduct contrary to these instructions and the Warranty will be deemed invalid.
AC-EBAR-N
125mm

HOw TO aTTaCH THe aCCessORY ON THe BaR
HOw TO RemOve THe aCCessORY fROm YOUR BaR
LaRgeR pRODUCTs
click
Features and presentations liable to changes without notice. Ref.WOI-140102-A1, 02/2023 edition.
➊– Put the springs on one side of
theaccessory into the groove on
the side of thewindow on the bar,
➋– Firmly push the 3 springs with your
thumb until they «click» into place*,
➌– The accessory is now secure.
Turn on theillumination to use.
➊– Use a small at head screwdriver as
a wedging tool & place it into the gap
between the spring and the bar light,
➋– Apply a light prising motion topop
the spring out of place,
➌– Repeat for remaining springson
the same side,
➍– Lift out of the bar light.
For larger products, simply start at one end
&add them on in aline. Always check that
all thesprings are secure.
* Double check all springs have clicked in place. The accessory MUST be mounted at for correct operation.
wenglor Straße 3
88069 Tettnang
Germany