Weslo Cadence5.8 Treadmill User manual

USER'S MANUAL
Serial
Number
Decal
Model No. WLTL27308.0
Serial No.
QUESTIONS?
As a manufacturer, we are commit-
ted to providing complete customer
satisfaction. f you have questions,
or if parts are missing, PLEASE DO
NOT CONTACT THE STORE;
please contact Customer Care.
IMPORTANT: You must note the
product model number and ser-
ial number (see the drawing
above) before contacting us:
CALL TOLL-FREE:
1-866-699-3756
Mon.–Fri. 6 a.m.–6 p.m. MST
Sat. 8 a.m.–4 p.m. MST
ON THE WEB:
www.wesloservice.com
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
V
Write the serial number in the
space above for future reference.

TABLE OF CONTENTS
WARNNGDECALPLACEMENT ..............................................................2
MPORTANTPRECAUTONS .................................................................3
BEFOREYOUBEGN .......................................................................5
ASSEMBLY ...............................................................................6
OPERATONANDADJUSTMENT ............................................................13
HOWTOFOLDANDMOVETHETREADMLL ..................................................18
TROUBLESHOOTNG ......................................................................20
EXERCSEGUDELNES ...................................................................22
PARTLST ...............................................................................23
EXPLODEDDRAWNG .....................................................................24
ORDERNGREPLACEMENTPARTS ..................................................BackCover
LMTEDWARRANTY...............................................................BackCover
WESLO is a registered trademark of CON P, nc.
2
This drawing shows the locations of the warning
decals. If a decal is missing or illegible, call the
telephone number on the front cover of this
manual and request a free replacement decal.
Apply the decal in the location shown. Note:
The decals may not be shown at actual size.
WARNING DECAL PLACEMENT
(Placed on
wire harness)

3
WARNING: To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
IMPORTANT PRECAUTIONS
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over age 35 or persons with
pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under age 12 and pets away
from the treadmill at all times.
8. The treadmill should not be used by persons
weighing more than 250 lbs. (113 kg).
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes; never use the treadmill with bare feet,
wearing only stockings, or in sandals.
11. When connecting the power cord (see page 13),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 13. To purchase a surge suppressor, see
your local WESLO dealer or call the telephone
number on the front cover of this manual and
order part number 146148, or see your local
electronics store.
13. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 20 if the treadmill is
not working properly.)
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
page 15).
17. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. Never leave the treadmill unattended while it
is running. Always remove the key, unplug the
power cord, and switch the reset/off circuit
breaker to the “off” position when the tread-
mill is not in use. (See the drawing on page 5
for the location of the reset/off circuit breaker.)

4
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6 and HOW TO FOLD
AND MOVE THE TREADMILL on page 18.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
21. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
22. Do not change the incline of the treadmill by
placing objects under the treadmill.
23. Inspect and properly tighten all parts of the
treadmill regularly.
24. Never drop or insert any object into any
opening on the treadmill.
25. DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
SAVE THESE INSTRUCTIONS

5
Thank you for selecting the new WESLO®CADENCE
CT 5.8 treadmill. The CADENCE CT 5.8 treadmill of-
fers a selection of features designed to make your
workouts at home more effective. And when youʼre not
exercising, the unique CADENCE CT 5.8 treadmill can
be folded up, requiring less than half the floor space of
other treadmills.
For your benefit, read this manual carefully before
using the treadmill. f you have questions after read-
ing this manual, please see the front cover of this man-
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.wesloservice.com/registration.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
BEFORE YOU BEGIN
Handrail
Storage Latch
Console
Key/Clip
Reset/Off
Circuit Breaker
Power Cord
ncline Pin/Leg
Walking Belt
Motor Hood
Wheel
Foot Rail
dler Roller
Adjustment Bolts
Accessory Tray

6
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This does not affect treadmill performance. f there is lubricant
on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own Phillips screwdriver ,
adjustable wrench , and wire cutters .
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART L ST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached
to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assem-
bly. Extra hardware may be included.
M10 x 110mm Bolt (1)–2
M10 x 80mm Bolt (4)–2
M10 x 58mm Bolt (2)–4
M10 Star
Washer (11)–2
M8 x 52mm Bolt (8)–2
M4.2 x 19mm
Screw (5)–6
M5 x 16mm
Screw (9)–2
M10 Nut
(15)–2
M5 Star
Washer (13)–2
M8 Nut
(16)–2
M8 Washer
(10)–4
M10 Washer
(12)–2
M8 x 16mm
Bolt (3)–6
M4.2 x 19mm
Tek Screw (6)–6
5/16" Star
Washer (14)–6
#10 x 1" Tek Screw
(7)–2

7
1. Make sure that the power cord is unplugged.
Attach the six Base Feet (90) to the bottom of
the Base (91) with six M4.2 x 19mm Tek Screws
(6).
3. Have a second person hold the Base (91) in the
position shown.
dentify the Right Upright (87), which has a large
hole near the lower end. Orient the Right
Upright as shown. Attach the Right Upright to
the Base (91) with two M10 x 58mm Bolts (2).
Do not tighten the Bolts yet.
Attach the Left Upright (86) to the Base (91)
in the same way. Orient the small holes as
shown.
91 6
6
90
90
1
6
6
6
90
90
90
2. Attach each Wheel (92) to the Base (91) with an
M10 x 80mm Bolt (4) and an M10 Nut (15).
92
4
2
4
15
15
3
87
Small
Holes
2
92
Large
Hole
91
86
2
91

8
5. Have a second person lift and hold the front end
of the Frame (61). Hold an Upright Spacer (88)
between the Right Upright (87) and the Frame.
Attach the Right Upright to the Frame with an
M10 x 110mm Bolt (1), an M10 Washer (12), and
an M10 Star Washer (11). Do not tighten the
Bolt yet.
Repeat this step on the left side of the tread-
mill.
5
61
1
87
88
12
11
4. With the help of a second person, raise the
Uprights (86, 87) so the Base (91) is flat on the
floor as shown. Next, position the front of the
Frame (61) between the Uprights.
See the inset drawing. Locate the wire tie in-
side of the lower end of the Right Upright (87).
Secure the wire tie to the Wire Harness (83).
Then, pull the upper end of the wire tie until the
end of the Wire Harness is extending from the
upper end of the Right Upright.
4
91
87
61
86
83 8387
Wire
Tie

9
6. dentify the Left Handrail Cover (80) and the
Right Handrail Cover (81). nsert the end of the
Left Handrail (79) through the large hole in the
Left Handrail Cover, and insert the end of Right
Handrail (82) through the large hole in the Right
Handrail Cover.
Attach the Handrail Covers (80, 81) to the
Handrails (79, 82) with two M4.2 x 19mm
Screws (5) in the locations shown.
5
81
Hole
Hole
5
80
82
79
6
7. Set the Console (94) face down on a soft sur-
face to avoid scratching the Console. Hold the
Right Handrail (82) near the Console as shown.
nsert the console wire into the large hole in the
side of the Right Handrail and out of the hole in
the top as shown.
82
7
Large
Hole
94
Console
Wire

10
8. Attach the Right Handrail (82) to the Console
(94) with an M5 x 16mm Screw (9), an M5 Star
Washer (13), and two M4.2 x 19mm Screws (5).
Make sure that no wires are pinched. Start all
three Screws before tightening any of them.
Tighten the M5 x 16mm Screw and then
tighten the M4.2 x 19mm Screws. Do not
overtighten the Screws.
Attach the Left Handrail (79) to the other side
of the Console (94) in the same way. Note:
There are no wires on the left side of the
Console.
Remove the plastic ties from the Right Handrail
(82) and the Left Handrail (79). f necessary,
press the M8 Cage Nuts (41) into place.
89
9
5
94
82
79
13
13
5
5
5
83
9
9. Have a second person hold the Console (94)
near the Right Upright (87) and the Left Upright
(not shown).
Connect the Wire Harness (83) to the console
wire. See the inset drawing. The connectors
should slide together easily and snap into
place. f they do not, turn one connector and try
again. IF THE CONNECTORS ARE NOT CON-
NECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS
TURNED ON. Remove the wire tie from the
Wire Harness. nsert the connectors and excess
wire into the Right Upright (87).
Next, insert the brackets on the Right Handrail
(82) and the Left Handrail (not shown) into the
Right Upright (87) and the Left Upright (not
shown). Make sure that no wires are pinched. 87
83
Console
Wire
94
41
41
Wire
Tie
Console
Wire
82