Westermo BRD-355 User manual

www.westermo.com
BRD-355
Industrial ADSL/VDSL Router

2
6623-2232

3
6623-2232
General information
Legal information
The contents of this document are provided “as is”. Except as required by applicable law,
no warranties of any kind, either express or implied, including, but not limited to, the
implied warranties of merchantability and fitness for a particular purpose, are made in
relation to the accuracy and reliability or contents of this document. Westermo reserves
the right to revise this document or withdraw it at any time without prior notice.
Under no circumstances shall Westermo be responsible for any loss of data or income or
any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at the following Internet address:
www.westermo.com

4
6623-2232
Safety information
Before installation:
Read this manual completely and gather all information on the unit. Make sure
that you understand it fully. Check that your application does not exceed the safe
operating specifications for this unit.
The unit must be installed by a service person and connected to a protective
earthing contact. Disconnect all telecommunication network connectors and
cable distribution system connectors before disconnecting the protective earthing
contacts.
This unit should be built-in to an apparatus cabinet, or similar, where access is
restricted to service personnel only.
The power supply wiring must be sufficiently fused, and if necessary it must be
possible to disconnect manually from the power supply. Ensure compliance to
national installation regulations.
This unit uses convection cooling. To avoid obstructing the airflow around the unit,
follow the spacing recommendations (see Cooling section).
This unit uses negative earth, therefore the 0 V and protective earth must be
connected to ensure robust functionality.
Before mounting, using or removing this unit:
Prevent access to hazardous voltage by disconnecting the unit from power supply.
Warning! Do not open connected unit. Hazardous voltage may occur within this
unit when connected to power supply.
Care recommendations
Follow the care recommendations below to maintain full operation of unit and to fulfil
the warranty obligations.
This unit must not be operating with removed covers or lids. Do not attempt to
disassemble the unit. There are no user serviceable parts inside. Do not drop, knock
or shake the unit, rough handling above the specification may cause damage to internal
circuit boards. Do not use harsh chemicals, cleaning solvents or strong detergents
to clean the unit. Do not paint the unit. Paint can clog the unit and prevent proper
operation. Do not expose the unit to any kind of liquids (rain, beverages, etc). The unit
is not waterproof. Keep the unit within the specified humidity levels. Do not use or
store the unit in dusty, dirty areas, connectors as well as other mechanical parts may be
damaged.
If the unit is not working properly, contact the place of purchase, nearest Westermo
distributor office or Westermo Tech support.
Maintenance
No maintenance is required, as long as the unit is used as intended within the specified
conditions.
!
!

5
6623-2232
Product disposal
This symbol means that the product shall not be treated as
unsorted municipal waste when disposing of it. It needs to
be handed over to an applicable collection point for recy-
cling electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will
help to reduce hazardous substances and prevent potential
negative consequences to both environment and human
health, which could be caused by inappropriate disposal.

6
6623-2232
Agency approvals and standards compliance
Type Approval / Compliance
EMC EN 61000-6-1, Immunity residential environments
EN 61000-6-2, Immunity industrial environments
EN 61000-6-3, Emission residential environments
EN 61000-6-4, Emission industrial environments
Safety EN 60950-1, IT equipment
Simplified EU declaration of conformity
Hereby, Westermo declares that the equipment is in compliance with applicable EU
directives. The full EU declaration of conformity and other detailed information are
available at the respective product page at www.westermo.com..

7
6623-2232
Type tests and environmental conditions
Phenomena Test Description Test levels
ESD EN 61000-4-2 Enclosure contact ± 6 kV (crit A)
Enclosure air ± 8 kV (crit A)
Radiated RF immunity IEC 61000-4-3 Enclosure 20 V/m (crit A)
(80 – 2700 MHz)
Fast transient EN 61000-4-4 DC power ports ± 2 kV (crit A)
Ethernet ports ± 2 kV (crit A)
Serial port ± 2 kV (crit B)
xDSL ports ± 2 kV (crit B)
Surge EN 61000-4-5 DC power ports ± 2 kV (crit A), 42 Ω
± 500 V (crit A), 12 Ω
Ethernet ports ± 2 kV (crit A), (shielded cable)
xDSL ports ± 2 kV (crit B)
RF conducted EN 61000-4-6 DC power ports 10 V/m, (crit A), (0.15 – 80 MHz)
Ethernet ports 3 V/m, (crit A), (0.15 – 80 MHz)
10 V/m, (crit B), (0.15 – 80 MHz)
xDSL ports 3 V/m (crit A), (0.15 – 80 MHz)
10 V/m (crit B), (0.15 – 80 MHz)
Radiated emission CISPR 16-2-3 Enclosure EN 61000-6-3
Conducted emission CISPR 16-2-1 DC power ports
EN 61000-6-3
CISPR 32 Ethernet ports
xDSL port
Temperature EN 60068-2-1
EN 60068-2-2
Operating –25 to +70°C (–13 to +158°F)
Storage & Transport –40 to +85°C (–40 to +185°F)
Humidity EN 60068-2-30 Operating 0 to 90% relative humidity non
condensing.
Storage & Transport 0 to 90% relative humidity non
condensing.
Altitude Operating 2000 m / 70 kPa
Service life Operating 10 year
Dimension W x H x D 53 x 103 x 97 mm
(2.08 x 4.05 x 3.81 in)
Weight 0.40 kg
Degree of protection IEC 529 Enclosure IP 40
Cooling Convection
Mounting Horizontal on 35 mm DIN-rail

8
6623-2232
Description
Remote access removes boundaries, eliminates the need for time consuming site visits
and provides a network infrastructure suitable for today's “always-on” society. The BRD-
355 is an industrially designed xDSL (ADSL/VDSL2) broadband router built to cope with
harsh environments and the characteristics of industrial applications. The unit supports a
wide range of xDSL-standards and has support for long lines.
Most devices today comes equipped with an Ethernet port for communications,
therefore the BRD-355 has a built-in two port Ethernet switch. For legacy connectivity
the unit also features one RS-232-port to provide multiple connection possibilities for
both new and legacy replacement installations. Designed to be installed on a DIN-rail
all connectors and LEDs have been positioned in the front of the unit, facing the user
for easy access and fast status feedback. With wide power input range, the unit can be
powered from 10 to 60 VDC and has low power consumption.
The cyber security features of the BRD-355 prevent unauthorized access and secure the
communication for Internet-enabled applications. The easy to use firewall filters incoming
traffic, allowing only approved packets to pass through. To inter-connect units with each
other securely over the Internet multiple VPN technologies are supported, including
IPsec and OpenVPN.
Upgrading legacy solutions to become IP-enabled can prove both costly and tedious
therefore the BRD-355 includes a wide feature set for various legacy applications
including both modem replacement methods as well as serial to Ethernet conversion.
If there are applications that require extra attention Westermo's extensive experience
from over 35 years within industrial data communications and over 5 years of industrial
xDSL expertise will be available to assist you.

9
6623-2232
Interface specifications
Power
Rated voltage 12 – 48 VDC
Operating voltage 10 – 60 VDC
Operational current (max) 450 mA @ 12 VDC
Rated current (max) 1000 mA @ 12 VDC
Rated frequency DC
RS-232
Electrical specification EIA RS-232
Data rate 300 bit/s – 115.2 kbit/s
Data format 7 or 8 data bits, Odd, even or none parity, 1 or 2 stop bits
Protocol Transparent, optimised by packing algorithm
Circuit type SELV
Transmission range 15 m / 49 ft
Connection 9 pin D-sub female
Shielded cable Not required
Conductive housing Ye s
Number of ports 1
Ethernet TX
Electrical specification IEEE std 802.3. 2005 Edition
Data rate 10 Mbit/s, 100 Mbit/s, manual or auto
Duplex Full or half, manual or auto
Circuit type SELV
Transmission range 100 m / 328 ft
Isolation to All other
Connection RJ-45 auto MDI/MDIX
Shielded cable Not required
Conductive housing Ye s
Number of ports 2

10
6623-2232
DSL
Protocol LLC/VC-MUX encap Ethernet, PPPoA, PPPoE, IPoA
Connection 1 x RJ-11
Version Common name Standard Downlink Uplink
ADSL ADSL ANSI T1.413 8 Mbit/s 1.0 Mbit/s
ADSL (G.dmt) ITU G.992.1 8 Mbit/s 1.0 Mbit/s
ADSL (G.lite) ITU G.992.2 1.5 Mbit/s 0.5 Mbit/s
ADSL over POTS ITU G.992.1 Annex A 12 Mbit/s 1.3 Mbit/s
ADSL over ISDN ITU G.992.1 Annex B 12 Mbit/s 1.8 Mbit/s
ADSL2 RE-ADSL ITU G.992.3 Annex L1/L2 5 Mbit/s 0.8 Mbit/s
ADSL2 ITU G.992.3 12 Mbit/s 1.3 Mbit/s
ADSL2 Annex J ITU G.992.3 Annex J 12 Mbit/s 3.5 Mbit/s
ADSL2+ ADSL2+ ITU G.992.5 24 Mbit/s 1.4 Mbit/s
ADSL2+ Annex M ITU G.992.5 Annex M 24 Mbit/s 3.3 Mbit/s
VDSL2 VDSL2 ITU G.993.2* 100 Mbit/s** 100 Mbit/s**
VDSL2 Vectoring ITU G.993.5 G.Vector 100 Mbit/s** 100 Mbit/s**
* Supports profiles 8a, 8b, 8c, 8d, 12a, 12b, 17a, 30a.
** Maximum sustained routing performance over time is around 35 Mbit/s.