Westermo Viper 008 User manual

www.westermo.com
Viper 008
Unmanaged 8-port Ethernet Switch

26641-2211

3
6641-2211
General information
Legal information
The contents of this document are provided “as is”. Except as required by applicable law,
no warranties of any kind, either express or implied, including, but not limited to, the
implied warranties of merchantability and fitness for a particular purpose, are made in
relation to the accuracy and reliability or contents of this document. Westermo reserves
the right to revise this document or withdraw it at any time without prior notice.
Under no circumstances shall Westermo be responsible for any loss of data or income or
any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at the following Internet address:
www.westermo.com

4
6641-2211
4
6641-2211
Safety
Before installation:
Read this manual completely and gather all information on the unit. Make sure
that you understand it fully. Check that your application does not exceed the safe
operating specifications for this unit.
This unit should only be installed by qualified personnel.
This unit should be built-in to an apparatus cabinet, or similar, where access is
restricted to service personnel only. The power supply wiring must be sufficiently
fused, and if necessary it must be possible to disconnect manually from all power
supply. Ensure compliance to national installation regulations. This unit relies on
convection cooling. Make sure that it is installed so that the ambient temperature
is within the specified temperature range, e.g. by avoiding obstruction of the
airflow around the unit. Also check chapter EN 45545-2 mounting notes.
The unit has no internal fuse and should be connected via an external fuse. The
fuse should be calculated in accordance with the rated current.
Before mounting, using or removing this unit:
Prevent access to hazardous voltage by disconnecting the unit from all power supply.
WARNING
Do not open connected unit. Hazardous voltage may occur within this unit when
connected to power supply.
Before powering-up, a protective earthing conductor must be connected to the
protective earthing terminal and have a cross-sectional area of at least 1.5 mm².
Note that this unit can be connected to two different power sources.
Be aware of that the surface of this unit may become hot. When this unit is
operated at high temperatures, the External Surface of Equipment may exceed
Touch Temperature Limit according to EN/IEC/UL 60950-1.
To reduce the risk of fire:
1. Use only No. 21 AWG or larger power cable
2. Use only No. 26 AWG or larger telecommunication line cord.
!
!

5
6641-2211
Care recommendations
Follow the care recommendations below to maintain full operation of unit and to fulfill
the warranty obligations:
…This unit must not be operating with removed covers or lids.
…Do not attempt to dissassemble the unit. There are not any user serviceable
parts inside.
…Do not drop, knock or shake the unit. Rough handling above the specification
may cause damage to internal circuit boards.
…Do not use harsh chemicals, cleaning solvents or strong detergents to clean the
unit.
…Do not expose the unit to any kind of liquid (water, beverages, paint etc). The
unit is not waterproof. Keep the unit within the specified humidity levels.
…Do not use or store the unit in dusty, dirty areas, connectors as well as other
mechanical part may be damaged.
…Do not cover or bring mechanical force to the ventilation membrane on the
back of the unit.
If the unit is not working properly, contact the place of purchase, nearest Westermo
distributor office or Westermo Tech support.
Maintenance
No maintenance is required, as long as the unit is used as intended within the specified
conditions.
Product disposal.
This symbol means that the product shall not be treated as
unsorted municipal waste when disposing of it. It needs to
be handed over to an applicable collection point for recy-
cling electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will
help to reduce hazardous substances and prevent potential
negative consequences to both environment and human
health, which could be caused by inappropriate disposal.

6
6641-2211
Agency approvals and standards compliance
FCC Part 15.105 Notice: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
… Reorient or relocate the receiving antenna
… Increase the separation between the equipment and receiver
… Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
… Consult the dealer or an experienced radio/TV technician for help.
Type Approval / Compliance
EMC EN 61000-6-1, Immunity residential environments
EN 61000-6-2, Immunity industrial environments
EN 61000-6-3, Emission residential environments
EN 61000-6-4, Emission industrial environments
EN 50121-3-2, Railway applications - EMC: Rolling stock – Apparatus
EN 50121-4, Railway signalling and telecommunications apparatus
IEC 62236-4, Railway signalling and telecommunications apparatus
Safety EN 60950-1, IT equipment
Environmental EN 50155 Railway applications - Electronic equipment used on rolling stock
Fire protection EN 45545-2, Fire protection on railway vehicles
Simplified EU declaration of conformity
Hereby, Westermo declares that the equipment is in compliance with applicable EU
directives. The full EU declaration of conformity and other detailed information are
available at the respective product page at www.westermo.com.

7
6641-2211
Type tests and environmental conditions
Phenomena Test Description Test levels
ESD EN 61000-4-2 Enclosure contact ± 6 kV (crit A)
Enclosure air ± 8 kV (crit A)
RF field AM modulated IEC 61000-4-3 Enclosure 20 V/m 80% AM (1 kHz),
80 – 2500 MHz (crit A)
Fast transient EN 61000-4-4 Ethernet ports ± 2 kV (crit A)
Earth port ± 2 kV (crit A)
Surge EN 61000-4-5 Fault port ± 2 kV line to earth (crit A)
Ethernet ports ± 2 kV line to earth (crit A)
Power port ± 2 kV line to earth, ± 2 kV line to line
(crit A)
RF conducted EN 61000-4-6 Ethernet ports 10 V 80% AM (1 kHz), 0.15 – 80 MHz
(crit A)
Power port 10 V 80% AM (1 kHz), 0.15 – 80 MHz
(crit A)
Power frequency magnetic
field
EN 61000-4-8 Enclosure 1000 A/m 50 Hz
300 A/m 16.7 Hz, 60 Hz, DC (crit A)
Pulse magnetic field EN 61000-4-9 Enclosure 300 A/m (crit A)
Voltage dips and interruption EN 50155 DC power ports 10 ms interruption, 100 ms ±40% voltage
variation
Radiated emission CISPR 16-2-3
ANSI C63.4
(FCC part 15)
Enclosure Class B (30 – 6000 MHz)
Conducted emission CISPR 16-2-1 DC power port &
Ethernet ports
Class B
Dielectric strength EN 50155 Ethernet ports to other
isolated ports
707 VDC 1 min
Power & Fault port to
other isolated ports 2121 VDC 1 min
Temperature EN 60068-2-1
EN 60068-2-2
Operating –40 to +70ºC
Storage & Transport –40 to +70ºC
Humidity EN 60068-2-30 Operating 5 to 95% relative humidity
Storage & Transport 5 to 95% relative humidity
Altitude Operating 2000 m / 70 kPa
Reliability prediction (MTBF) MIL-C217F2 Operating Ground Benign:
150 years @ 20 ºC
147 years @ 40 ºC
135 years @ 60 ºC
Ground Mobile:
9,87 years @ 20 ºC
9,85 years @ 40 ºC
9,79 years @ 60 ºC
Ground Fix:
28,54 years @ 20 ºC
28,43 years @ 40 ºC
27,95 years @ 60 ºC
Service life Operating 10 year
Vibration, random simulated
long life
IEC 60068-2-64,
Cat. 1 class B
(EN 61373)
Not Operating Vertical: 7.9 m/s2
Transverse: 7.9 m/s2
Longitudinal: 7.9 m/s2
3 x 5 h
Vibration, random functional IEC 60068-2-64,
Cat. 1 class B
(EN 61373)
Operating Vertical: 1.0 m/s2
Transverse: 1.0 m/s2
Longitudinal: 1.0 m/s2
3 x 10 min

8
6641-2211
Phenomena Test Description Test levels
Shock, half sine pulses IEC 60068-2-27,
Cat. 1 class B
(EN 61373)
Operating Vertical: 50 m/s2
Transverse: 50 m/s2
Longitudinal: 50 m/s2
30 ms, 3 x 6 shocks
Shock, sawtooth IEC 60068-2-27,
Cat. 1 class B
(IEEE1478-2001)
Operating Vertical: 100 m/s2
Transverse: 100 m/s2
Longitudinal: 100 m/s2
11 ms, 3 x 6 shocks
Enclosure UL 94 Nickel coated zinc Flammability class V-1
Dimension W x H x D 175 x 100 x 53,4 mm
Weight 0.9 kg
Degree of protection IEC 529 Enclosure IP 65 when all ports are protected/
connected else IP 40
Cooling Convection
Mounting DIN Rail or wall mounted

9
6641-2211
Description
Functional description
Viper 008 is a unmanaged switch developed for rail and industrial applications. To meet
the environmental requirements from rail and harsh industrial applications the switch
has rugged M12 Ethernet connectors and full metal housing. The IP65 sealed metal case
make it robust and allows for the surrounding air temperature to be between –40 to
+70°C. There are no sensitive or fragile components, hardening the product against
shock and vibration making these units suitable for rolling stock usage. The power supply
operates over a wide input range from 24 to 110 VDC.
Interface specifications
Power and fault relay port PWR
Rated voltage 24 to 110 VDC
Operating voltage 16.8 to 143 VDC (14.4 to 154 VDC for 100 ms)
Rated current 110 mA @ 24 VDC
33 mA @ 110 VDC
Rated frequency DC
Inrush current, I2t Max 0.02 A2s @ 24 – 110 VDC
Polarity Reverse polarity protected
Startup current* 300 mA @ 16.8 VDC
Redundant power input No
Isolation to Connections X1 – X8 and to ground, 1500 VAC.
Fault relay belongs to the same isolation group as the power
supply lines (fault relay signals are also contained within
PWR).
Connection 4 pin male M12 connector with A-code
Connector size M12, recommended cable area 0.5 mm2 recommended
(minimum 0.25 mm2), cable dimensions depend on choice of
M12 connector
Shielded cable Not required, twisted pair is recommended
Fault relay resistance < 10 Ω
* If external power supply is used it must meet specified startup current.
M12 A-Coded
Power
Connector
Position Direction Description
1 U+ Positive supply voltage
2 Out Alarm relay (status) +
30 V Negative supply voltage
4 Out Alarm relay (status) –
Housing Shield Chassis of product (ground)

10
6641-2211
Fault Contact
The Viper switch is equipped with a potential free normally closed fault contact. The
fault contact is a solid state component (relay) that requires power to work and it is
transient protected. Additionally, the fault contact is opened when any of the following
conditions is met:
• No voltage on the power supply pin, a voltage level outside the legal voltage range
or current limitation on the voltage source is applied on the power input.
Description of how connection to the fault contact could be done is shown below. The
relay is closed when the unit is OK and open at failure. The relay is of semiconductor
type (no moving parts). It is specified for max current 250 mA continuous, 500 mA
peak (10 ms), operational voltage up to 110 V, protected by a 150 VDC-varistor,
ON-resistance less than 10 Ohm, and leakage current max 1 µA.
External relay
+24/48 VDC +
1 kΩ
0V
Viper
2 2
4 4
Viper
To logic input
Input on PLC
Service port
The Service Port should not be used by non other than the Westermo Technical Support
team. Do not connect any device or cable to the Service Port.