Westin PRO TRAXX 4 User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-3085-RevB ECO #: W16-0069 DATE: 10/7/16
INSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS,
PRO TRAXX 4 & 5 OVAL TUBE STEP BAR
APPLICATION:
2015-+ Chevrolet Colorado / GMC Canyon Extended / Crew Cab
PART NUMBER:
21-24000, 21-24005, 21-24010, 21-24015,
21-54000, 21-54005, 21-54010, 21-54015
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
1,2 2STEP BAR, DRIVER(1) AND PASSENGER(2) 13MM SOCKET
36MOUNTING BRACKETS ALLEN WRENCH
412 M8 HEX CAP SCREW (YELLOW ZINC) SOCKET EXT.
512 M8 FLAT WASHER (YELLOW ZINC) HEX HEY TOOL
612 M8 SPLIT LOCK WASHER (YELLOW ZINC) RATCHET
712 M8 U-CLIP NUT (YELLOW ZINC) TORQUE WRENCH
812 M10 INTERNAL TOOTHED LOCK WASHER (BLACK ZINC)
912 M10 FLAT WASHER (BLACK ZINC)
10 12 M10 BUTTON HEAD SCREW (BLACK ZINC)
11 12 M6 HEX HEAD CAP SCREW (BLACK ZINC)
12 24 M6 FLAT WASHER (BLACK ZINC)
13 12 M6 NYLON NUT (BLACK ZINC)
14 6PLASTIC BRACKET COVER
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
ITEM 3
Pro Traxx 5 Pro Traxx 4
ITEM 3ITEM 14
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim.

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-3085-RevB ECO #: W16-0069 DATE: 10/7/16
2. If vehicle has plastic covers, remove the designated covers where mounts will be placed from the rocker panel, see Figure
1.
3. Install M8 u-clip nuts in the holes where the plastic covers were removed, see Figure 2. Note: See Figure 6 for placement
of all designated u-clips.
4. Loosely install mounting brackets to the previously install M8 u-clips with supplied M8 hardware. Note: The middle
bracket will be closer the front bracket then in comparison to the rear bracket.
5. Locate (1) plastic bracket cover (Item 14) and loosely secure it to the (6) brackets using the provided hardware: (2) M6 hex
head cap screws, (4) M6 flat washers, and (2) M6 nylon nuts. Repeat for every bracket. See Figure 4.
6. Loosely install the Pro Traxx step bar assembly to the previously installed mounting brackets with supplied M10 hardware.
See Figure 5. Note: Driver side step tube will be packaged in a clear poly tube and passenger side will be packaged
in a red poly tube, the Westin logo should face outward when installed.
7. Align and adjust as necessary then torque hardware: M8 to 15-18 ft-lbs., M10 to 30-35 ft-lbs., and M6 to 5-7 ft-lbs.
Install supplied M8 u-clip
nuts in designated areas.
Figure 2
Remove rubber covers.
Figure 1
Install mounting
brackets with sup-
plied M8 hardware.
Figure 3 Front Driver
Side Shown
Figure 4 Pro Traxx 4 Only
Install step bar
with supplied
M10 hardware.
Front Driver Side ShownFigure 5

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-3085-RevB ECO #: W16-0069 DATE: 10/7/16
Care Instructions
 REGULAR WAXING IS RECOMMENDED. DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES.
 STAINLESS STEEL PRODUCTS CAN BE CLEANED WITH MILD SOAP AND WATER. STAINLESS STEEL POLISH SHOULD BE USED TO POLISH SMALL SCRATCHES.
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER.
INSTALLATION COMPLETE
CREW CAB
EXTENDED CAB
Plastic Bracket Covers not shown.
Full View Driver Side
Figure 6
FRONT
REAR

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-3085-RevB ECO #: W16-0069 DATE: 10/7/16
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RESULT IN
PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY:
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product. Us-
er should never exceed the vehicle manufacturers maximum tow and weight rating regardless of
the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS
VEHICLE DAMAGE.
WARNING
AUTOMOTIVE PRODUCTS, INC.