Whalen WMFP48FH-10-KD User manual

Media Fireplace Console
Stock # WMFP48FH-10-KD
# WMFP48FH-10-KG
# WMFP48FH-10-KW
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2018-03-15 Rev. 0001-B

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Media Fireplace Console
MADE IN CHINA
How to adjust the European adjustable hinges on doors
Shipping may cause doors to go out of alignment. If you find that the doors need to be adjusted
slightly, turn the appropriate screw, as illustrated.
1. TO ADJUST DOOR FORWARD OR BACKWARD.
2. TO ADJUST DOOR TO RIGHT OR TO LEFT.
3. TO ADJUST DOOR UP OR DOWN.
MAXIMUM LOAD 50 lb. (22.6 kg)
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT
LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR
EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTER OF THE UNIT; THE
BASE OF THE TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE
UNIT WITHOUT OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR
FLAT PANEL TVS INCLUDING OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND
WEIGHT LIMITS COULD FALL OFFOR BREAKTHE UNIT, CAUSING POSSIBLE SERIOUS INJURY.
1
2
MAXIMUM RECOMMENDED WEIGHT LOADS
FITS UP TO MOST 55” FLAT PANEL TVs
MAXIMUM LOAD 100 lb. (45.3 kg)
PLACE TV BEHIND THE STOPPER

3
Important
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the fireplace.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel ( Qty. 1 ) B- Upper Side Panel ( Qty. 2 ) C- Upper Front Panel ( Qty. 2 )
D- Upper Partition Panel ( Qty. 1 ) E- Center Shelf ( Qty. 1 ) F- Left Lower Side Panel ( Qty. 1 )
G- Right Lower Side Panel H- Left Lower Partition Panel I- Right Lower Partition Panel
( Qty. 1 ) ( Qty. 1 ) ( Qty. 1 )
J- Lower Back Panel ( Qty. 2 ) K- Center Crossbar ( Qty. 1 ) L- Middle Stile (Qty. 2)
M- Bottom Panel (Qty. 1) N- Bottom Back Stretcher (Qty. 1) O- Bottom Front Stretcher (Qty. 1)
P- Bottom Front Molding Q- Upper Back Panel R- Door S- Adjustable Shelf
(
Qty. 1 ) ( Qty. 1 ) ( Qty. 2 ) ( Qty. 2 )

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
T- Stop Rail ( Qty. 1 ) Fireplace Insert (Qty. 1) Remote Control with Battery (Qty. 1)
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 51+2 extra) (Qty. 51+2 extra) (Qty. 64+2 extra)
(4) Straight Metal Bracket (5) M4 x 38 mm Screw (6) M3 x 15 mm Flat Head Screw
(Qty. 2) (Qty. 12+1 extra) (Qty. 12+1 extra)
(7) M3.5 x 15 mm Washer Head Screw (8) Shelf Support (9) Cam Lock Cover
(Qty. 16+1 extra) (Qty. 8+1 extra) (Qty. 24+1 extra)
(10) Knob (Qty. 2) (11) 25 mm Handle Bolt (Qty. 2) (12) Rubber Bumper (Qty. 4+1 extra)
(13) Triangle Metal Plate (Qty. 2) (14) Floor Leveler (Qty. 2) Glue (Qty. 1)
Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (Qty. 2)
(Included in plastic bag)
Tools required: Phillips screwdriver and rubber mallet (not provided).

6
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely crew the Cam Bolts (2) into the designated small holes on the Top Panel (A), Bottom Panel
(M), Lower Side Panels (F and G) and Upper Front Panels (C) using a Phillips screwdriver.
Cam Bolt
(26 used in this step)
②
A
M
F
G
C
C

7
Assembly Instructions
3. Securely screw seventeen Cam Bolts (2) into the designated small holes on the Center Shelf (E) on both
sides.
E
E
2
Cam Bolt
(17 used in this step)
②

8
Assembly Instructions
4. Securely screw the Cam Bolts (2) into the designated small holes on the Lower Partition Panels (H and
I).
Cam Bolt
(8 used in this step)
②
H
H
I
I
2

9
Assembly Instructions
5. Attach the Middle Crossbar (K) to the Center Shelf (E) with two Wood Dowels (3) and three Cam
Locks (1) (Refer to page 3 on Cam Lock system operation supplement).
NOTE: Make sure that you use a small amount of glue with both ends of all dowels.
Cam Lock
(3 used in this step)
①
M8 x 30 mm Wood Dowel
(2 used in this step)
③
E
K
3
1

10
Assembly Instructions
6. Attach one Front Panel (C) to one Upper Side Panel (B) with one Wood Dowel (3) and two Cam Locks
(1).
7. Repeat the previous step to combine the other Front Panel (C) with the other Upper Side Panel (B)
together.
B
C
3
1
Cam Lock
(4 used in this step)
①
M8 x 30 mm Wood Dowel
(2 used in this step)
③
X 2

11
Assembly Instructions
8. Attach one Middle Stile (L) to the Left Lower Partition Panel (H) with two Wood Dowels (3) and two
Cam Locks (1).
9. Fasten one Lower Back Panel (J) to the Left Lower Partition Panel (H) with three Wood Dowels (3) and
two Cam Locks (1).
10. Repeat the same procedure to attach the other Middle Stile (L) and Back Panel (J) to the Right Lower
Partition (I).
H
J
L
I
L
J
1
3
M8 x 30 mm Wood Dowel
(10 used in this step)
③
Cam Lock
(8 used in this step)
①

12
Assembly Instructions
11. Attach the Bottom Front Stretcher (O) to the Bottom Front Molding (P) with four Wood Dowels (3) and
eight 38 mm Screws (5).
O
P
5
5
5
5
3
3
3
3
M8 x 30 mm Wood Dowel
(4 used in this step)
③
M4 x 38 mm Screw
(8 used in this step)
⑤

13
Assembly Instructions
12. Attach the Bottom Stretchers (N and O) to the Bottom Panel (M) with four Wood Dowel (3) and six
Cam Locks (1).
1
3
M
NOP
Cam Lock
(6 used in this step)
①
M8 x 30 mm Wood Dowel
(4 used in this step)
③

14
Assembly Instructions
13. Attach the Left Lower Partition Panel assembly to the Bottom Panel (M) with four Wood Dowels (3)
and two 38 mm Screws (5).
14. Repeat the same procedure to attach the Right Lower Partition Panel assembly at the opposite end.
M8 x 30 mm Wood Dowel
(8 used in this step)
③
M4 x 38 mm Screw
(4 used in this step)
⑤
5
55
5
M
J
H
I
J

15
Assembly Instructions
15. Attach the Left Lower Side Panel (F) to the Panels (J, M and N) with six Wood Dowels (3) and three
Cam Locks (1).
16. Repeat the same procedure to attach the Right Lower Side Panel (G) at the opposite end.
M8 x 30 mm Wood Dowel
(12 used in this step)
③
Cam Lock
(6 used in this step)
①
1
13
3
H
J
M
N
I
G
J
F

16
Assembly Instructions
17. Attach the Center Shelf assembly to the Panels (F, G, H and I) with twelve Wood Dowels (3) and eight
Cam Locks (1).
F
H
I
J
G
J
E
1
3
M8 x 30 mm Wood Dowel
(12 used in this step)
③
Cam Lock
(8 used in this step)
①

17
Assembly Instructions
18. Attach the Upper Side Panel assemblies to the Center Shelf (E) with four Wood Dowels (3) and four
Cam Locks (1).
19. Fasten the Upper Partition Panel (D) to the Center Shelf (E) with one Wood Dowel (3) and two Cam
Locks (1).
E
B
D
B
1
3
M8 x 30 mm Wood Dowel
(5 used in this step)
③
Cam Lock
(6 used in this step)
①

18
Assembly Instructions
20. Attach the Top Panel (A) to the Panels (B and D) with five Wood Dowels (3) and six Cam Locks (1).
1
3
B
D
B
A
M8 x 30 mm Wood Dowel
(5 used in this step)
③
Cam Lock
(6 used in this step)
①

19
Assembly Instructions
21. Using the pilot holes as a guide, fasten two Triangle Metal Plates (13) at the bottom joints between the
Bottom Front Molding (P) and Lower Side Panels (F and G) using four 15 mm Screws (6) per plate.
6
6
13
F
G
P
M
Triangle Metal Plate
(2 used in this step)
⑬
M3 x 15 mm Flat Head Screw
(8 used in this step)
⑥

20
Assembly Instructions
22. Tightly screw two Floor Levelers (14) into the Triangle Metal Plates (13) and set to the correct height.
14
14
F
G
P
M
Floor Leveler
(2 used in this step)
⑭