Whalen Shelby WSF72SY26C User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2019-04-22 Rev. 0001-A
Shelby 72in Fireplace
Model # WSF72SY26C
# WSF72SY26M
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our website www.whalenfurniture.com
Or e-mail your request to: [e-mail]
LOT NUMBER:
DATE PURCHASE
D
:
/
/

2
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or
replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet
your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to State.
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenfurniture.com
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG : Shelby 72in Fireplace
MODEL #: WSF72SY26C / WSF72SY26M
MADE IN CHINA
M A X I M U M R E C O M M E N D E D W E I G H T L O A D S
Place TV behind the stopper
Fits up to most 203.2 cm / 80 in. flat panel TVs
Maximum load 61.2 kg / 135 lb
Maximum load 22.7 kg / 50 lb
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS.
NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR EQUIPMENT. TO
AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTRE OF THE UNIT; THE BASE OF THE
TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE UNIT WITHOUT
OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS
OR OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS COULD FALL
OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIO
US INJURY.

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH THE DOWELS. EXCESS GLUE CAN BE
WIPED OFF WITH A DAMP CLOTH.
Insert Dowel at least half way by tapping lightly with a rubber mallet (not included), IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the pre-drilled small holes on the panel. Connect both panels together; making sure
the Cam Bolt goes into the pre-drilled hole at the end of the panel with the Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole in the panel. Make sure the arrow on the Cam Lock is
pointed towards the Cam Bolt.
3. Once the Cam Bolt is connected inside the Cam Lock, take a Phillips screwdriver (not included) and
tighten the Cam Lock clockwise.
4. Plug the Cam Lock Cover into the cross slot of the Cam Locks to conceal the cam.
You are now ready to assemble the KD unit.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Fixed Shelf (Qty. 1) C- Bottom Panel (Qty. 1
)
D- Left Side Panel (Qty. 1) E- Right Side Panel (Qty. 1) F- Left Lower Partition (Qty. 1)
G- Right Lower Partition (Qty. 1) H- Upper Partition (Qty. 1) I- Middle Crossbar Assembly (Qty. 1)
J- Middle Left Stile (Qty. 1) K- Middle Right Stile (Qty. 1) L- Base Front Molding (Qty. 1)
M- Left Bottom Molding (Qty. 1) N- Right Bottom Molding (Qty. 1) O- Base Rear Stretcher (Qty. 1)
P- Base Front Stretcher (Qty. 1) Q- Door (Qty. 2) R- Door Glass Insert (Qty. 2)
S- Adjustable Shelf (Qty. 2) T- Upper Back Panel (Qty. 1) U- Lower Back Panel (Qty. 2)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are
present before beginning assembly.
V- Firebox Support (Qty. 1) Fireplace Insert (Qty. 1) Remote control with battery (Qty. 1)
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel (4) #8 x 1-1/2” Screw
(Qty. 39+1 extra) (Qty. 39+1 extra) (Qty. 48+2 extra) (Qty. 32+1 extra)
(5) Acrylic Stopper (6) #8 x 1” Screw (7) #3 x 5/8” Black Screw (8) #3 x 5/8” Washer Head Screw
(Qty. 1) (Qty. 2) (Qty. 4+1 extra) (Qty. 35+1 extra)
(9) #4 x 5/8” Zinc Screw (10) 2” Self-tapping Screw (11) Metal Bracket (12) Cam Lock Cover
(Qty. 24+1 extra) (Qty. 2+1 extra) (Qty. 2) (Qty. 20+1 extra)
(13) Shelf Support (Qty. 8+1 extra) (14) Knob (Qty. 2) (15) 28 mm Knob Bolt (Qty. 2)
(16) Rubber Bumper (Qty. 4+1 extra) (17) Hinge (Qty. 4) Glue (Qty. 1)
Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (Qty. 2)
(Included in plastic bag)
Tools required (not included): Phillips screwdriver, stud finder, power drill, pencil, measure tape, and 3
mm/0.1 drill bit.

6
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (2) into the designated small holes on the Fixed Shelf (B), Bottom Panel
(C), Lower Partitions (F and G) using a Phillips screwdriver, as shown in the illustration.
3. Insert two Wood Dowels (3) into the inner holes of the Middle Crossbar Assembly (I). Tap in with a
rubber mallet, if necessary. Make sure that you use a small amount of glue with both ends of all dowels.
4. Align the drilled holes on the Fixed Shelf (B) with the inserted Wood Dowel (3) on the Middle Crossbar
Assembly (I), and then press them together. Attach the Middle Crossbar Assembly (I) in place by
engaging three Cam Locks (1) (Refer to page 3 on Cam Lock system operation supplement).
B
1
3
I
C
B
G
F
2

7
Assembly Instructions
5. Align and attach the Base Rear Stretcher (O) to the Bottom Panel (C) with three wood dowels (3) and
four cam locks (1), as shown.
6. Align and attach the Middle Left Stile (J) to the Left Lower Partition Panel (F) by using two Wood
Dowels (3) and three Cam Locks (1).
7. Repeat last step to combine the Middle Right Stile (K) with the Right Lower Partition Panel (G)
together.
G
F
J
K
1
3
C
O
1
3

8
Assembly Instructions
8. Glue four Wood Dowels (3) into the inner holes of the Lower Partition Panels (F and G) and attach
them to the Fixed Shelf (B) by engaging four Cam Locks (1).
9. Glue four Wood Dowels (3) into the bottom holes of the Lower Partition Panels (F and G) and position
the Bottom Panel (C) onto the inserted Wood Dowels (3). Attach the Bottom Panel (C) in place with
four 1-1/2” Wood Screws (4).
F
G
C
4
3
3
4
B
F
JG
K
3

9
Assembly Instructions
10. Securely screw the Cam Bolts (2) into the designated small holes on the Left and Right Side Panels (D
and E) using a Phillips screwdriver.
11. Glue three Wood Dowels (3) into the inner holes on the Left Bottom Molding (M) and fasten it to the
Left Side Panel (D) with six 1-1/2” Wood Screws (4).
12. Repeat last step to combine the Right Bottom Molding (N) with the Right Side Panel (E) together.
D
E
2
D
E
M
N
3
4
3
4

10
Assembly Instructions
13. Glue ten Wood Dowels (3) into the large holes on the Bottom Panel (C), Base Rear Stretcher (O) and
Fixed Shelf (B) at both ends.
14. Align the large holes on the Left Side Panel (D) with the inserted Wood Dowels (3). Firmly press them
together and fasten it in place by engaging five Cam Locks (1).
15. Repeat last step to attach Right Side Panel (E) at the other end.
16. Align and attach the Base Front Stretcher (P) to the Bottom Panel (C) with three wood dowels (3) and
four cam locks (1) as shown.
E
D
C
B
O
1
E
D
C
P
1