Whelen Engineering Company Inner Edge XLP DUO+ 01-0687688-1 Series User manual

Page 1
©2014 Whelen Engineering Company Inc.
Form No.14771C (011819)
Automotive: Lightbars
For warranty information regarding this product, visit www.whelen.com/warranty
• Proper installation of this product requires the installer to have a good understanding of automotive electronics, systems and procedures.
• Whelen Engineering requires the use of waterproof butt splices and/or connectors if that connector could be exposed to moisture.
• Any holes, either created or utilized by this product, should be made both air- and watertight using a sealant recommended by your vehicle
manufacturer.
• Failure to use specified installation parts and/or hardware will void the product warranty.
• If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other vital parts could be damaged
by the drilling process. Check both sides of the mounting surface before drilling begins. Also de-burr the holes and remove any metal shards
or remnants. Install grommets into all wire passage holes.
• If this manual states that this product may be mounted with suction cups, magnets, tape or Velcro®, clean the mounting surface with a 50/50
mix of isopropyl alcohol and water and dry thoroughly.
• Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or located in the air bag deployment
area will damage or reduce the effectiveness of the air bag, or become a projectile that could cause serious personal injury or death. Refer to
your vehicle owner’s manual for the air bag deployment area. The User/Installer assumes full responsibility to determine proper mounting
location, based on providing ultimate safety to all passengers inside the vehicle.
• For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be made. The recommended
procedure requires the product ground wire to be connected directly to the NEGATIVE (-) battery post (this does not include products that use
cigar power cords).
• If this product uses a remote device for activation or control, make sure that this device is located in an area that allows both the vehicle and
the device to be operated safely in any driving condition.
• Do not attempt to activate or control this device in a hazardous driving situation.
• This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a combination of these lights. Do not stare directly into
these lights. Momentary blindness and/or eye damage could result.
• Use only soap and water to clean the outer lens. Use of other chemicals could result in premature lens cracking (crazing) and discoloration.
Lenses in this condition have significantly reduced effectiveness and should be replaced immediately. Inspect and operate this product
regularly to confirm its proper operation and mounting condition. Do not use a pressure washer to clean this product.
• It is recommended that these instructions be stored in a safe place and referred to when performing maintenance and/or reinstallation of this
product.
• FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT OR VEHICLE
AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!
Warnings to Installers
Whelen’s emergency vehicle warning devices must be properly mounted and wired in order to be effective and safe. Read and follow all of Whelen’s written
instructions when installing or using this device. Emergency vehicles are often operated under high speed stressful conditions which must be accounted for
when installing all emergency warning devices. Controls should be placed within convenient reach of the operator so that they can operate the system without
taking their eyes off the roadway. Emergency warning devices can require high electrical voltages and/or currents. Properly protect and use caution around
live electrical connections.Grounding or shorting of electrical connections can cause high current arcing, which can cause personal injury and/or vehicle
damage, including fire. Many electronic devices used in emergency vehicles can create or be affected by electromagnetic interference. Therefore, after
installation of any electronic device it is necessary to test all electronic equipment simultaneously to insure that they operate free of interference from other
components within the vehicle. Never power emergency warning equipment from the same circuit or share the same grounding circuit with radio
communication equipment. All devices should be mounted in accordance with the manufacturer’s instructions and securely fastened to vehicle elements of
sufficient strength to withstand the forces applied to the device. Driver and/or passenger air bags (SRS) will affect the way equipment should be mounted. This
device should be mounted by permanent installation and within the zones specified by the vehicle manufacturer, if any. Any device mounted in the deployment
area of an air bag will damage or reduce the effectiveness of the air bag and may damage or dislodge the device. Installer must be sure that this device, its
mounting hardware and electrical supply wiring does not interfere with the air bag or the SRS wiring or sensors. Mounting the unit inside the vehicle by a
method other than permanent installation is not recommended as unit may become dislodged during swerving; sudden braking or collision. Failure to follow
instructions can result in personal injury. Whelen assumes no liability for any loss resulting from the use of this warning device. PROPER INSTALLATION
COMBINED WITH OPERATOR TRAINING IN THE PROPER USE OF EMERGENCY WARNING DEVICES IS ESSENTIAL TO INSURE THE SAFETY OF
EMERGENCY PERSONNEL AND THE PUBLIC.
Warnings to Users
Whelen’s emergency vehicle warning devices are intended to alert other operators and pedestrians to the presence and operation of emergency vehicles and
personnel. However, the use of this or any other Whelen emergency warning device does not guarantee that you will have the right-of-way or that other
drivers and pedestrians will properly heed an emergency warning signal. Never assume you have the right-of-way. It is your responsibility to proceed safely
before entering an intersection, driving against traffic, responding at a high rate of speed, or walking on or around traffic lanes. Emergency vehicle warning
devices should be tested on a daily basis to ensure that they operate properly. When in actual use, the operator must ensure that both visual and audible
warnings are not blocked by vehicle components (i.e.: open trunks or compartment doors), people, vehicles, or other obstructions. It is the user’s responsibility
to understand and obey all laws regarding emergency warning devices. The user should be familiar with all applicable laws and regulations prior to the use of
any emergency vehicle warning device. Whelen’s audible warning devices are designed to project sound in a forward direction away from the vehicle
occupants. However, because sustained periodic exposure to loud sounds can cause hearing loss, all audible warning devices should be installed and
operated in accordance with the standards established by the National Fire Protection Association.
Safety First
This document provides all the necessary information to allow your Whelen product to be properly and safely installed. Before beginning the installation and/or
operation of your new product, the installation technician and operator must read this manual completely. Important information is contained herein that could
prevent serious injury or damage.
WARNING: This product can expose you to chemicals including Lead which is known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Installation Guide:
Inner Edge® XLP Low Current DUO+™ Lightbar
(6- & 12-Light)
51 Winthrop Road
Chester, Connecticut 06412-0684
Phone: [phone]
Internet: www.whelen.com
Sales e-mail: [e-mail]
Customer Service e-mail: [email protected]
®
ENGINEERING COMPANY INC.

Page 2
10 X 1" PHILLIPS
PAN HD SHEET
METAL SCREW
(type A) (QTY 1)
#8-32 x 3/8 TORX HD
SCREW (QTY 2)
VISOR
SWIVEL
BRACKET
VISOR CLIP BRACKET
Fig. 2
SHEET METAL
HEADLINER
VISOR CLIP MOUNTING
BRACKET
SHEET
METAL
ROOF
RUBBER SEAL
Lightbar
Side View
WI
N
DS
H
IE
L
D
Side View
DRIVER DOOR
Pry plastic
cover off
VISOR SWIVEL
BRACKET
WINDSHIELD
Remove screw
and visor clip
VISOR
CLIP
MOUNTING CLIP
(remove)
V
I
S
O
R
Fig. 3
WINDSHIELD
Install Faston grommet
into existing hole in roof
that clip snapped into.
Fig. 4Fig. 4
Re-install visor clip over bracket
using supplied #8 X 1" sheet metal screw
Install into Faston grommet using
supplied 1/4 X 1-1/4" PPHSMS
Install into Faston grommet using
supplied 1/4 X 1-1/4" PPHSMS
Install into Faston grommet using
supplied 1/4 X 1-1/4" PPHSMS
MOUNTING
BRACKET
Fig. 5Fig. 5
IMPORTANT! The lightbar should be a minimum of 16" from radio antennas!
Installation / Standard:
1. Loosen (do not remove) the three screws securing the passenger-side visor
swivel bracket to the vehicle.
2. Remove screws securing vehicles visor clip and remove clip and hardware.
3. Secure mounting bracket to Inner Edge housing using hardware provided (Fig. 1).
4. Position the keyed opening of the mounting bracket directly under the location of
the visor clip removed in step 2 and remount the visor clip in its original location
using the original hardware (See Spacer installation in Fig. 1).
5. Firmly tighten any hardware loosened in this procedure.
6. Repeat this procedure for the driver-side assembly.
7. When rubber seal is in full contact with vehicle windshield and roof preventing
light output from entering passenger compartment tighten mounting hardware.
8. Route the lightbar cable down the vehicle A-pillar to your control head. Make all
wiring connections using the information in the wiring diagram.
Installation / Caprice:
1. Secure the mounting bracket to the Inner Edge housing using the two
#8 - 32 X
3/8 TORX
HEAD SCREWS
provided (Fig. 2).
2. Loosen (do not remove) the
screws securing the passenger-side visor
swivel bracket to the vehicle.
3. Slide the outside end of the mounting bracket under the visor swivel bracket (Fig.
2). At the same time slip the rectangular hole in the other end of the mounting
bracket over the visor clip bracket. With the mounting bracket in position retighten
the visor swivel bracket hardware.
4. Using the screw hole in the mounting bracket as a guide, drill a pilot hole into the
sheet metal behind the headliner and secure other side of mounting bracket using
the supplied #10 X 1” PHILLIPS PAN HEAD SHEET METAL SCREW.
5. Repeat this procedure for the driver-side assembly.
6. The rubber seal should be in full contact with the windshield and the rear of the
lightbar should be in contact with the roof to prevent light from entering the
passenger compartment. When this has been achieved, tighten all mounting
hardware firmly to maintain contact (Fig. 2).
7. Route the lightbar cable down the vehicle A-pillar to your control head and make
all wiring connections using the information in the wiring diagram.
Installation 2013 Ford Fusion:
Figures 1 thru 3 show the driver side of the interior, looking up at the roof.
1. On the driver side visor swivel bracket, carefully pry the plastic cover off of the
front of the bracket (Fig. 3). The lightbar mounting bracket will sit in the space that
the cover occupied. NOTE: Pry the cover off using two flat blade screwdrivers
on each side to avoid braking the cover. The cover will not be used here but
should be saved in case you wish to remove the lightbar in the future.
2. Remove the swivel bracket mounting clip (located under the cover you removed in
step 1) and lift the swivel bracket assembly out. Install the supplied fastex
grommet into the hole in the roof sheet metal which the clip snapped into. Reinsert
the swivel bracket assembly (Figs. 3 & 4).
3. On the vehicle visor clip, remove the screw holding on the clip (The supplied #8 X
1" sheet metal screw will replace this screw) and remove the clip. (Figs. 3 & 4).
4. Secure the mounting bracket to the lightbar and position the bracket where it will
mount on the vehicle (Fig. 1 side view). NOTE: The rubber seal should be in full
contact with the windshield and the rear of the lightbar should be in contact
with the roof to prevent light from entering the passenger compartment
5. Secure the lightbar bracket to the swivel mount using the supplied 1/4 X 1-1/4”
Phillips Pan Head Sheet Metal Screw. This screw will thread into the fastex
grommet you installed in step 2 and the bracket sits where the cover was (Fig. 6).
6. Line the rectangular hole in the other end of the lightbar bracket, up with the visor
clip and install the visor clip
over the lightbar bracket using
the supplied #8 X 1” Sheet
Metal Screw (Fig. 5).
7. Make sure all mounting
hardware is tightened firmly
and repeat procedure for the
passenger side of the vehicle.
8. Extend the cables and connect
to power. Refer to the lightbar
manual for wiring and fusing
information.
Fig. 6
1/4 X 1-1/4"
PPHSMS
GROMMET
HEADLINER
VISOR SWIVEL
BRACKET
ROOF SHEET METAL
The Tahoe and Silverado have a retainer
which holds the headliner to the visor
clip that must be replaced
with the supplied spacer.
PASSENGER
SIDE
Under visor
swivel bracket Under
visor clip
Fig. 1
HEADLINER
VISOR CLIP
side view
VISOR CLIP
side view
VISOR CLIP
side view
SPACER
Explorer bracket
shown for example
Mounting
Bracket
ROOFROOF
#8-32 x 3/8 Torx
Hd Screw (2)
R
U
BBER
S
EAL
Lightbar Side ViewLightbar Side View
WI
N
DS
H
IE
L
D
SPACER
HEADLINER
BRACKET

Page 3
Warning
Warning
1 - 42
1 - 40
1 - 40
1 - 40
1 - 40
1 - 42
1 - 33
1-33
1 - 33
1 - 33
1 - 33
1 - 33
OFF
WARNING
FLASHING TAKEDOWN
FLASHING TAKEDOWN & WARNING alternate
TAKEDOWN
TAKEDOWN
TAKEDOWN
TAKEDOWN
WARNING OVERRIDE (#12 is the Default Pattern)
WARNING OVERRIDE (#12 is the Default Pattern)
FLASHING TD & WARNING OVERRIDE alternate
FLASHING TD & WARNING OVERRIDE alternate
TAKEDOWN & WARNING OVERRIDE alternate
TAKEDOWN
TAKEDOWN
TAKEDOWN
Flashing
TakeDown
Flashing
Takedown
Warning &
Flashing TD
Takedown
Warning
Override
Takedown
Warning
Override
FUNCTION
AVAILABLE PATTERNSSWITCH POSITIONS
off
ON
ON
ON
ON
ON
ON
ON
ON
off
ON
ON
ON
ON
ON
ON
ON
ON
off
ON
ON
ON
ON
ON
ON
ON
ON
off
ON
ON
ON
ON
ON
ON
ON
ON
Wiring and Operation:
WARNING! All customer supplied wires that connect to the positive terminal of
the battery must be sized to supply at least 125% of the maximum operating
current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT
BREAKERS WITH THIS PRODUCT!
This lightbar is powered and controlled by an 8-conductor cable. The lightbar
operates in 4 basic modes. Take-down, Flashing Take-down, Warning Override
and Warning. You can operate in any one of these modes or combine them.
When you switch on more than one mode they will operate as follows:
• Take-down will override any other mode.
• Flashing Take-down will flash alternately with either Warning Override or
Warning if either is activated when Flashing Take-Down is activated.
• Warning Override will override Warning.
Example: If you switched on all four modes at once, Take-down would run. If you
turn Take-down off, (Leaving Flashing Take-down, Warning Override and Warning)
Flashing Take-down would alternate with Warning Override.
This allows you to run in one mode and then switch to another by only turning off one
switch instead of turning one off and another on. Example: If you activate Take-down
and Warning, you will run in Take-down mode. By switching off Take-down you will
immediately go to Warning (see chart below for other options).
White/Green - Scan-Lock™
The WHITE/GREEN wire allows you to choose from available flash patterns.
You must activate the lighthead to select a pattern:
TO CYCLE THROUGH ALL PATTERNS: To cycle forward, apply +12 VDC to the
WHITE/GREEN wire for less than 1 second and release. To cycle backward, apply
+12 VDC to the WHITE/GREEN wire for more than 1 second and release.
TO SET A PATTERN AS DEFAULT: When the pattern is displayed, allow it to run for
more than 5 seconds. The lighthead will now display this pattern when activated.
TO RESET TO THE FACTORY DEFAULT PATTERN: Turn off power and apply +12
VDC to the WHITE/GREEN wire while turning power on.
A normally open momentary switch is best suited for Scan-Lock operation.
Brown: Hi/Low Power
This feature works for Warning or Warning Override. With low power activated,
you may choose from four light intensities using Scanlock. The type of switch
depends on how you wish Hi/Low to function:
Latching Mode: (momentary switch) Apply positive voltage to the BROWN wire for
less than 1 second and the lightbar is “latched” into low power. Apply positive voltage
for several seconds and release to restore normal operation.
Level Mode: (toggle switch) Applying positive voltage to the wire for more than 1
second holds the lightbar in low power mode until voltage is removed.
Warning Patterns:
1.ActionScan™
2.SignalAlert™ 75 ALT
3.SignalAlert™ 75 ALT/IO/CH
4.CometFlash® 75 ALT
5.CometFlash® 75 ALT/IO/CH
6.DoubleFlash 75 ALT
7.DoubleFlash 75 ALT/IO/CH
8.SingleFlash 75 ALT
9.SingleFlash 75 ALT/IO/CH
10.LongBurst™ 75 ALT
11.LongBurst™ 75 ALT/IO/CH
12.SingleFlash 60 ALT
13.SingleFlash 60 ALT/IO/CH
14.SingleFlash 90 ALT
15.SingleFlash 90 ALT/IO/CH
16.SingleFlash 120 ALT
17.SingleFlash 120 ALT/IO/CH
18.SingleFlash 240 ALT
19.SingleFlash 240 ALT/IO/CH
20.DoubleFlash 120 ALT
21.DoubleFlash 120 ALT/IO/CH
22.ActionFlash™ 75 ALT
23.ActionFlash™ 75 ALT/IO/CH
24.ActionFlash™ 150 ALT
25.ActionFlash™ 150 ALT/IO/CH
26.MicroBurst™ ALT
27.MicroBurst™ ALT/IO/CH
28.PingPong™ 75 ALT
29.PingPong™ 75 ALT/IO/CH
30.FlimFlam ALT
31.FlimFlam ALT/IO/CH
32.Moduflash™ ALT
33.Moduflash™ ALT/IO/CH
34.Cylon 1 Lamp
35.Cylon 2 Lamp
36.Cylon Chaser
37.Eyeballs SYNC
38.Eyeballs IN/OUT
39.2 Eyeballs IN/OUT
40.Eyeballs CRAZY
41.CRUISE - LOW
42.CRUISE - HIGH
ALT = Alternating
ALT/IO/CH = Pattern cycles from
Alternating to IN/OUT to
Checkerboard
Flashing Take-Down
Patterns:
43. SingleFlash 240
44. DoubleFlash 120
45. ActionFlash™ 75
46. ActionFlash™ 150
47. MicroBurst™
48. PingPong™ 75
49. FlimFlam
50. Moduflash™
51. SignalAlert™ 75
52.CometFlash® 75
53. DoubleFlash 75
54. SingleFlash 75
55. LongBurst™ 75
56. SingleFlash 60
57. SingleFlash 90
58. SingleFlash 120
Take-Down
Configurations:
59. ALL
60. INNER
61. OUTER
WHT/ORG
WHT/GRN
ORG
BRN
WHT/BLK
BLU
Warning Override
ScanLock
Warning
Low Power
Takedown
Flashing Takedown
RED +VBAT
Ground (-)
BLK
(+)
Battery
(-)
= Momentary Switch
(Normally Open)
= SP/ST Switch
= Fuse
15A 1A

Page 4
FORD
PART NUMBER KEY
01-0687688- _ _
YEAR/MAKE
2013 - TAURUS/INTERCPTR1-
2013 - EXPLORER/SUV2-
INTERCEPTOR2- 2013 -
2013 - F1503-
2013 - F250-5504-
2013 - EXPEDITION5-
2013 - CHARGER6-
2013 - RAM 15007 -
2013 - DURANGO8-
2013 - CAPRICE PPV9 -
2014 - IMPALAA-
2013 - TAHOE/SUBURBAN/ALL PICKUPSB-
2013 - FUSIONC-
2014 - TAHOE/SUBURBAN/ALL PICKUPSD-
2015 - F150E-
2018 - EXPEDITIONF-
2019 - SILVERADO 1500G-
2020 - EXPLORER/SUV INTERCEPTORH-
VERSION
6 LT1-
12 LT2-
6 LT (CAL STEADY)3-
12 LT (CAL STEADY)4-
2013 - TAURUS/INTERCEPTOR
01-0687688-11
01-0687688-12
11-36E737-107
11-36E737-007
07-287414-123
07-287414-023
11-26E674-007
11-26E674-107
1
1
11
1
1
1
11
COVER, TOPDRVR 12 TAURUS DUO INNER EDGE XLPBLACK
BASE, HOUSING DRVR 12 TAURUS DUO INNER EDGE XLPBLACK
BASE, HOUSING PASS 12 TAURUS DUO INNER EDGE XLPBLACK
COVER, TOPPASS 12 TAURUS DUO INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR TAURUS INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS TAURUS INNER EDGE XLPBLACK
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
14-08228C-06D
2
4
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER DESCRIPTION
QTYQTY
D
E
F
G
A
2013 - EXPLORER/SUV INTERCEPTOR
01-0687688-21
01-0687688-22
11-26E741-107
11-26E741-007
07-287371-123
07-287371-023
11-36E300-007
11-36E300-107
1
1
11
1
1
1
11
BASE, HOUSING DRIVER BLACK 13 FORDSUV INNER EDGE XLP
COVER, TOPDRIVER BLACK 13 FORDSUV DUO INNER EDGE XLP
COVER, TOPPASS BLACK 13 FORDSUV DUO INNER EDGE XLP
BASE, HOUSING PASS BLACK 13 FORDSUV INNER EDGE XLP
BRACKET, VISOR MT DRVR BLK 13 FORDSUV INNER EDGE XLP
BRACKET, VISOR MT PASS BLK 13 FORDSUV INNER EDGE XLP
14-08228C-06D
2
4
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
B
C
ITEM PART NUMBER
DESCRIPTION
QTYQTY
D
E
F
G
A
2013 - F150
01-0687688-31
01-0687688-32
11-26E834-107
11-26E834-007
07-287501-123
07-287501-023
11-36E829-007
11-36E829-107
BASE,HOUSING DRVR 13 FORDF150 INNER EDGE XLPBLACK
COVER, TOPDRVR 13 FORDF-150 DUO INNER EDGE XLPBLACK
COVER, TOPPASS 13 FORDF-150 DUO INNER EDGE XLPBLACK
BASE,HOUSING PASS 13 FORDF150 INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR 13 F150 INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS 13 F150 INNER EDGE XLPBLACK
14-08228C-06D
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
1
1
11
1
1
1
11
2
4
B
C
ITEM PART NUMBER
DESCRIPTION
QTYQTY
D
E
F
G
A
2013 - F250-550
01-0687688-41
01-0687688-42
11-26E849-107
11-26E849-007
07-287511-123
07-287511-023
11-36E848-007
11-36E848-107
1
1
11
1
1
1
11
BASE, HOUSING DRVR 13 F250/350 INNER EDGE XLPBLACK
COVER, TOPDRVR 2013 F250/350 DUO INNER EDGE XLPBLACK
COVER, TOPPASS 2013 F250/350 DUO INNER EDGE XLPBLACK
BASE, HOUSING PASS 13 F250/350 INNER EDGE XLPBLACK
BRACKET,VISOR MT DRVR F250/350 INNER EDGE XLPBLACK
BRACKET,VISOR MT PASS F250/350 INNER EDGE XLPBLACK
14-08228C-06D
2
4
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
B
C
ITEM PART NUMBER
DESCRIPTION
QTYQTY
D
E
F
G
A
D
6
2
56
2
1
4
1
B
PASSENGER SIDE BRACKET
F
A
C
814-08228C-06D
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
101-026E763-01
SUB ASSY, LC I/O INNER-EDGE DUO XLP
01-026E756D_3
SUB ASSY, WARNING */WHT DUO INNER-EDGE XLP, DRVR
01-026E756P_3
SUB ASSY, WARNING */WHT DUO INNER-EDGE XLP, PASS
4
1
01-0687688-_1
DUO INNER EDGE XLP, LC 6 LT
238-0546827-14
TRIM, SEAL HOUSING/WINDSHIELD13.600" LENGTH INNER EDGE XLP
1
01-0687688-_2
DUO INNER EDGE XLP, LC 12 LT
SCREW, 4-40 X 1/4 PPHMS 410SS BLACK PASSIVATE
14-040216-04H2614
6
66
8
1
4
1
21
2614
6
66
01-0687688-_3
DUO INNER EDGE XLP, LC 6 LT (CAL STEADY)
01-0687688-_4
DUO INNER EDGE XLP, LC 12 LT (CAL STEADY)
2
ITEM PART NUMBER DESCRIPTION
QTYQTYQTYQTY
5
6
3
4
1
2015 - F150
2013 - EXPEDITION
01-0687688-51
01-0687688-52
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
1
1
11
1
1
1
11
2
4
11-26G042-107
11-26G042-007
07-287845-123
07-287846-023
11-36G031-007
11-36G031-107
BASE, HOUSING DRVR EXPEDITION INNER EDGE XLPBLACK
COVER, TOPDRVR 14 EXPEDITION DUO INNER EDGE XLPBLACK
COVER, TOPPASS 14 EXPEDITION DUO INNER EDGE XLPBLACK
BASE, HOUSING PASS EXPEDITION INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR EXPEDITION INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS EXPEDITION INNER EDGE XLPBLACK
14-08228C-06D
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER
DESCRIPTION
QTYQTY
D
E
F
G
A
01-0687688-E1
01-0687688-E2
11-26G375-107
11-26G375-007
07-287988-123
07-287988-023
11-36G373-007
11-36G373-107
BASE,HOUSING DRVR 15 FORDF150 INNER EDGE XLPBLACK
COVER, TOPDRVR 15 FORDF-150 DUO INNER EDGE XLPBLACK
COVER, TOPPASS 15 FORDF-150 DUO INNER EDGE XLPBLACK
BASE,HOUSING PASS 15 FORDF150 INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR 15 F150 INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS 15 F150 INNER EDGE XLPBLACK
14-08228C-06D
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
1
1
11
1
1
1
11
2
4
B
C
ITEM PART NUMBER
DESCRIPTION
QTYQTY
D
E
F
G
A
2013 - FUSION
01-0687688-C1
01-0687688-C2
21-12081205-3
SCREW GROMMET, FASTEX #212-240602-040101
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
11-26E925-107
11-26E925-007
07-287529-123
07-287529-023
11-36E891-007
11-36E891-107
BASE, HOUSING DRVR 2013 FUSION INNER EDGE XLPBLACK
COVER, TOPDRVR FORDFUSION DUO INNER EDGE XLPBLACK
COVER, TOPPASS FORDFUSION DUO INNER EDGE XLPBLACK
BASE, HOUSING PASS 2013 FUSION INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR FUSION INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS FUSION INNER EDGE XLPBLACK
1
1
11
1
1
1
11
12
21 15-131416-202
SCREW, 1/4 X 11/4 PPHSMS SS TYPEA
21 15-081416-160
SCREW, 8 X 1PPHSMS
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
14-08228C-06D
2
4
B
C
ITEM PART NUMBER
DESCRIPTION
QTYQTY
D
E
F
G
A
H
I
J
2020 - EXPLORER/SUV INTERCEPTOR
1
1
11
1
1
1
11
2
4
B
C
ITEM PART NUMBER
DESCRIPTION
QTYQTY
D
E
F
G
A
11-26J430-107
11-26J430-007
07-288609-123
07-288609-023
11-36J428-007
11-36J428-107
BASE, HOUSING DRVR 2020 UTILITY INNER EDGE XLPBLACK
COVER, TOPDRVR 2020 UTILITY WC INNER EDGE XLPBLACK
COVER, TOPPASS 2020 UTILITY WC INNER EDGE XLPBLACK
BASE, HOUSING PASS 2020 UTILITY INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR 2020 UTILITY INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS 2020 UTILITY INNER EDGE XLPBLACK
14-08228C-06D
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
01-0687688-H1
01-0687688-H2
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT

Page 5
FORD
DODGE
CHEVROLET
2018 - EXPEDITION
01-0687688-F1
01-0687688-F2
11-26J157-107
11-26J157-007
07-288533-123
07-288533-023
11-36J151-007
11-36J151-107
1
1
11
1
1
1
11
BASE, HOUSING DRVR EXPEDITION INNER EDGE XLPBLACK
COVER, TOPDRVR '18 EXPEDITION WC INNER EDGE XLPBLACK
COVER, TOPPASS '18 EXPEDITION WC INNER EDGE XLPBLACK
BASE, HOUSING PASS EXPEDITION INNER EDGE XLPBLACK
BRACKET, VISOR MT DS EXPEDITION INNER EDGE XLPBLACK
BRACKET, VISOR MT PS EXPEDITION INNER EDGE XLPBLACK
14-08228C-06D
2
4
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
B
C
ITEM PART NUMBER
DESCRIPTION
QTYQTY
D
E
F
G
A
2020 - EXPLORER/SUV INTERCEPTOR
01-0687688-H1
01-0687688-H2
11-26J430-107
11-26J430-007
07-288609-123
07-288609-023
11-36J428-007
11-36J428-107
1
1
11
1
1
1
11
BASE, HOUSING DRVR 2020 UTILITY INNER EDGE XLPBLACK
COVER, TOPDRVR 2020 UTILITY WC INNER EDGE XLPBLACK
COVER, TOPPASS 2020 UTILITY WC INNER EDGE XLPBLACK
BASE, HOUSING PASS 2020 UTILITY INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR 2020 UTILITY INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS 2020 UTILITY INNER EDGE XLPBLACK
14-08228C-06D
2
4
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
B
C
ITEM PART NUMBER
DESCRIPTION
QTYQTY
D
E
F
G
A
2013 - CHARGER
01-0687688-61
01-0687688-62
11-26E670-107
11-26E670-007
07-287356-123
07-287356-023
11-36E264-007
11-36E264-107
1
1
11
1
1
1
11
BASE, HOUSING DRVR 12 CHARGER INNER EDGE XLPBLACK
COVER, TOPDRVR 12 CHARGER DUO INNER EDGE XLPBLACK
COVER, TOPPASS 12 CHARGER DUO INNER EDGE XLPBLACK
BASE, HOUSING PASS 12 CHARGER INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR CHARGER INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS CHARGER INNER EDGE XLPBLACK
14-08228C-06D
2
4
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
B
C
ITEM PART NUMBER DESCRIPTION
QTYQTY
D
E
F
G
A
2013 - CAPRICE PPV
01-0687688-91
01-0687688-92
11-26E740-107
11-26E740-007
07-287419-123
07-287419-023
11-36E494-007
11-36E494-107
1
1
11
1
1
1
11
BASE, HOUSING DRVR 12 CAPRICE INNER EDGE XLPBLACK
COVER, TOPDRVR 12 CAPRICE DUO INNER EDGE XLPBLACK
COVER, TOPPASS 12 CAPRICE DUO INNER EDGE XLPBLACK
BASE, HOUSING PASS 12 CAPRICE INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR CAPRICE INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS CAPRICE INNER EDGE XLPBLACK
14-08228C-06D
15-10141B-162
2
4
12
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
SCREW, 10 X 1" PPH SMS TYPE A SS BLACK OXIDE
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
B
C
ITEM PART NUMBER DESCRIPTION
QTYQTY
D
E
F
G
H
A
2014 - IMPALA
01-0687688-A1
01-0687688-A2
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
1
1
11
1
1
1
11
2
4
11-26G262-107
11-26G262-007
07-287946-123
07-287946-023
11-36G260-007
11-36G260-107
14-08228C-06D
BASE, HOUSING DRVR 2014 IMPALA INNER EDGE XLPBLACK
COVER, TOPDRVR 2014 IMPALA DUO INNER EDGE XLPBLACK
COVER, TOPPASS 2014 IMPALA DUO INNER EDGE XLPBLACK
BASE, HOUSING PASS 2014 IMPALA INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR IMPALA INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS IMPALA INNER EDGE XLPBLACK
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER DESCRIPTION
QTYQTY
D
E
F
G
A
2014 - TAHOE/SUBURBAN/ALL PICKUPS
01-0687688-D1
01-0687688-D2
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
-
1
-
-
1
11
1
1
1
11
2
4
11-26F653-107
11-26F653-007
07-287726-123
07-287726-023
11-36F641-007
11-36F641-107
14-08228C-06D
BASE, HOUSING DRVR 14 TAHOE INNER EDGE XLPBLACK
COVER, TOPDRVR 2014 TAHOE DUO INNER EDGE XLPBLACK
COVER, TOPPASS 2014 TAHOE DUO INNER EDGE XLPBLACK
BASE, HOUSING PASS 14 TAHOE INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR TAHOE INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS TAHOE INNER EDGE XLPBLACK
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER DESCRIPTION
QTYQTY
D
E
F
G
A
2013 - DURANGO
01-0687688-81
01-0687688-82
11-26F188-107
11-26F188-007
07-287616-123
07-287616-023
11-36F186-007
11-36F186-107
BASE, HOUSING DRVR 13 DURANGO INNER EDGE XLPBLACK
COVER, TOPDRVR DODGE DURANGO DUO INNER EDGE XLPBLACK
COVER, TOPPASS DODGE DURANGO DUO INNER EDGE XLPBLACK
BASE, HOUSING PASS 13 DURANGO INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR DURANGO INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS DURANGO INNER EDGE XLPBLACK
14-08228C-06D
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
1
1
11
1
1
1
11
2
4
B
C
ITEM PART NUMBER DESCRIPTION
QTYQTY
D
E
F
G
A
2013 - TAHOE/SUBURBAN/ALL PICKUPS
01-0687688-B1
01-0687688-B2
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
1
1
11
1
1
1
11
2
4
11-26E761-107
11-26E761-007
07-287449-123
07-287449-023
11-36E644-007
11-36E644-107
14-08228C-06D
BASE, HOUSING DRVR 12 TAHOE INNER EDGE XLPBLACK
COVER, TOPDRVR 2012 TAHOE DUO INNER EDGE XLPBLACK
COVER, TOPPASS 2012 TAHOE DUO INNER EDGE XLPBLACK
BASE, HOUSING PASS 12 TAHOE INNER EDGE XLPBLACK
BRACKET, VISOR MT DRVR TAHOE INNER EDGE XLPBLACK
BRACKET, VISOR MT PASS TAHOE INNER EDGE XLPBLACK
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER DESCRIPTION
QTYQTY
D
E
F
G
A
2019 - SILVERADO 1500
01-0687688-G1
01-0687688-G2
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
1
1
11
1
1
1
11
2
4
11-26J272-107
11-26J272-007
07-288558-123
07-288558-023
11-36J270-007
11-36J270-107
14-08228C-06D
BASE, HOUSING DRVR SILVERADO 2019 INNER EDGE XLPBLK
COVER, TOPDRVR 19 SILVERADO WC INNER EDGE XLPBLK
COVER, TOPPASS 19 SILVERADO WC INNER EDGE XLPBLK
BASE, HOUSING PASS SILVERADO 2019 INNER EDGE XLPBLK
BRCKT, VISOR MT DRV SILVERADO 2019 INNER EDGE XLPBLK
BRCKT, VISOR MT PAS SILVERADO 2019 INNER EDGE XLPBLK
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
B
C
ITEM PART NUMBER DESCRIPTION
QTYQTY
D
E
F
G
A
2013 - RAM 1500
01-0687688-71
01-0687688-72
FINAL, DUO INNER EDGE XLP, 6 LIGHT
FINAL, DUO INNER EDGE XLP, 12 LIGHT
BASE, HOUSING DRVR RAM 1500 INNER EDGE XLPBLACK
BASE, HOUSING PASS RAM 1500 INNER EDGE XLPBLACK
COVER, TOPDRVR DODGE RAM 1500 DUO INNER EDGE XLPBLACK
COVER, TOPPASS DODGE RAM 1500 DUO INNER EDGE XLPBLACK
11-26E882-107
11-26E882-007
07-287518-123
07-287518-023
11-36E862-007
11-36E862-107
BRACKET,VISOR MT DRVR RAM 1500 INNER EDGE XLPBLACK
BRACKET,VISOR MT PASS RAM 1500 INNER EDGE XLPBLACK
14-08228C-06D
SCREW, 8-32X 3/8" PAN TORX HDROLOK SS BLACK OXIDE
1
1
11
1
1
1
11
2
4
15-081416-160
SCREW, 8 X 1PPHSMS
12
B
C
ITEM PART NUMBER DESCRIPTION
QTYQTY
D
E
F
G
A
H