Whelen Engineering Company WeCanX V2V User manual

Page 1
©2020 Whelen Engineering Company Inc.
Form No.14D18A (061720)
Installation Guide:
WeCanX™ V2V Sync Module
®
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: [phone]
Internet: www.whelen.com
Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visit www.whelen.com/warranty
Automotive: Serial Communications
WARNING: This product can expose you to chemicals including Lead which is known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information go to www.P65Warnings.ca.gov.
©2020 Whelen Engineering Company Inc.
Form No.14D18A (061720)
Installation Guide:
WeCanX™ V2V Sync Module
®
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: [phone]
Internet: www.whelen.com
Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visit www.whelen.com/warranty
Automotive: Serial Communications
WARNING: This product can expose you to chemicals including Lead which is known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Mounting the V2V Module
WINDOW
MOUNTING
Mounting to Dash, Rear Deck or other surface:
Mounting to Vehicle:
It is recommended you mount the module to the dashboard or rear deck of the vehicle however it can be mounted to any surface or
window. If mounted to a window it is recommended to use VELCRO® hook & loop tape. The module be mounted face upmust
(side with logo). This is the side that receives the signal. If mounted to a window, the face must point out of the vehicle.
8 X 3/4 Phillips
Pan Head
Sheet Metal
Screw
Mounting Surface
Front (side with logo)
of Module must face up
IMPORTANT: Module must be
mounted inside the vehicle in
a location not exposed to
excessive heat or weather.
It is the responsibility of the
installation technician to
make sure the installation
and operation of this product
will not interfere with or
compromise the operation or
efficiency of any other vehicle
equipment!
IMPORTANT!
Before returning the vehicle
to active service, visually
confirm the proper operation
of this product, as well as all
vehicle components or
equipment.
Mounting the V2V Module
WINDOW
MOUNTING
Mounting to Dash, Rear Deck or other surface:
Mounting to Vehicle:
It is recommended you mount the module to the dashboard or rear deck of the vehicle however it can be mounted to any surface or
window. If mounted to a window it is recommended to use VELCRO® hook & loop tape. The module be mounted face upmust
(side with logo). This is the side that receives the signal. If mounted to a window, the face must point out of the vehicle.
8 X 3/4 Phillips
Pan Head
Sheet Metal
Screw
Mounting Surface
Front (side with logo)
of Module must face up
IMPORTANT: Module must be
mounted inside the vehicle in
a location not exposed to
excessive heat or weather.
It is the responsibility of the
installation technician to
make sure the installation
and operation of this product
will not interfere with or
compromise the operation or
efficiency of any other vehicle
equipment!
IMPORTANT!
Before returning the vehicle
to active service, visually
confirm the proper operation
of this product, as well as all
vehicle components or
equipment.

Page 2
RED
GRN
GRY
BLK
GRY
BLK/WHT
GRN
J18
Core Main Box
1
2
3
(+)
Battery
Fuse @
1 AMP
(-)
S ecificationsp:
Input Voltage: +12 VDC
Current Draw: 30 mA
Wire as shown installing a
customer supplied fuse into
the power wire. Plug the
connector into J18 of Core
Main Box and operate using
tthe Core system.
V2V Sync Module:
POWERED BY
TM
V2V SYNC MODULE
MOUNT THIS SIDE
FACING TOWARD WINDOW
FOR GPS ACCURACY:
DIAGNOSTIC INDICATOR:
RED: No GPS
GREEN: GPS / Weak Signal
GPS / Strong SignalBLUE:
Bad ConnectionCYCLE R-G-B:
RED
GRN
GRY
BLK
GRY
BLK/WHT
GRN
J18
Core Main Box
1
2
3
(+)
Battery
Fuse @
1 AMP
(-)
S ecificationsp:
Input Voltage: +12 VDC
Current Draw: 30 mA
Wire as shown installing a
customer supplied fuse into
the power wire. Plug the
connector into J18 of Core
Main Box and operate using
tthe Core system.
V2V Sync Module:
POWERED BY
TM
V2V SYNC MODULE
MOUNT THIS SIDE
FACING TOWARD WINDOW
FOR GPS ACCURACY:
DIAGNOSTIC INDICATOR:
RED: No GPS
GREEN: GPS / Weak Signal
GPS / Strong SignalBLUE:
Bad ConnectionCYCLE R-G-B: