Whirlpool PORTABLE AIR CONDITIONER Original operating instructions

Copy your Model and
Serial Numbershere...
When you need service or call with a question,
have this information ready:
1.
Complete Model and Serial Numbers (Model
and Serial Numbers are on a plate attached to
the front of the unit. You can see it after
2.
removing the plastic front panel.)
Purchase date from sales slip.
Copy this information in these spaces. Keep
this book. vour warrantv and sales slip toaether
in a handy place, (To remove front panel,
see page 12.)
BEFORE YOU USE YOUR
AIR CONDITIONER
It is your responsibilityto make
surethat your air conditioner:
l Has been properly installed.
l Is the right size for the area you want
to cool.
l Is properly connected to electricity.
l Is properly electrically grounded.
l Is properly used only for the job it was
intended to do.
l Is not used by children or anyone not
able to operate it properly.
l Is properly maintained.
l Also, remove energy label and buy guide.
Use damp cloth to take off any glue
residue. Do not use a sharp instrument
or any harsh or abrasive cleaners.
Energy SavingTips
l Improve home insulation (seal doors,
windows, and close fireplace flue).
l Close blinds or drapes on sunny side of
house; add window awnings.
l Keep air filter clean. Don’t block air flow
with drapes or furniture.
l Ventilate attic (high temperature levels
add to normal cooling load).
l Try not to use heat producing appliances
during the hottest part of the day. Turn
lights, radios, televisions, and other
appliances off when not needed.
l Keep heat registers and cool air returns
closed or blocked off so cooled air won’t
escape.
l Use a vent fan in areas where cooking,
laundry, or bathing is done to pull out
extra heat and moisture near its source.
Contents
page paw
Before You Use Your Air Conditioner .... 2 Cleaning and Caring for Your
Energy Tips ........................ 2 Air Conditioner .................... 12
Electrical Requirements ............... 3 Cooling Load Guide ................. 14
Installation Instructions ............... 7 Self-Service Checklist ................ 15
How to Start and Service Information ................. 15
Use Your Air Conditioner ............ 10
GJl985 Whirlpool Corporation

Electrical Requiremerrts
For Your Air Conditioner
‘i ;* *ppII’rrar-,.~~~~~~,~IIF!~~.~I -eeli. i L i*r,.<
BELOW ARE ELECTRICAL PLUGVARIATIONS.CHOOSE
THE ONE WHICH MATCHES THE AMPERE RATING OF
YOUR UNIT. THE NUMBER OF AMPERES IS PRINTED
ON THE SERIAL PLATE, ATTACHED TO THE FRONT OF
THE UNIT, BEHIND THE FRONT PANEL (SEE PAGE 2).
Chart-A
PLUG TYPE
3-PRONG
GROUNDING PLUG
3- PRONG
GROUNDING
TYPE WALL
RECEPTACLE
POWER SUPPLY CORD
GROVNO PRONG
SEE ELECTRICAL
REQUIREMENTS
For 115 volt models with
serial plate amperes up
through 12.0
For 230 volt and 2301208
volt models with serial
plate amperes up through
12.0
For 230 volt and 2301208
volt models with serial
plate amperes up through
16.0
For 230 volt and 2301208
volt models with serial
plate amperes up through
24.0
ELECTRICAL
REQUIREMENTS
For 115 volt models with serial plate amperes up
through 12.0
OBSERVE ALL LOCAL GOVERNING CODES
AND ORDINANCES
Do not, under any circumstances, remove the
power supply cord ground prong.
RECEPTACLE WIRING
RECEPTACLE WIRING should be at least as
large as 14 cauge. Use copper wire only. It is the
personai responsibility and obligation of the
customer to provide proper and adequate
receptacle wiring installed by a qualified electri-
cian. OBSERVE NATIONAL ELECTRICAL
CODE AND ALL LOCAL GOVERNING
CODES AND ORDINANCES.
Electrical Requirements
A 115 volt (103.5 min., 126.5 max.) 60 hertz AC
only, 15 ampere fused electrical supply is required
(time delay fuse or time delay circuit breaker re-
quired). It is required that a separate circuit, serving
only this appliance, be provided. Do not use an
extension cord.
Electrical Connection
Electrical Ground is Required on this Appliance
RECOMMENDED GROUNDING METHOD
For your personal safety, this appliance must be
grounded. This appliance is equipped with a
power supply cord having a 3-prong grounding
plug. To minimize possible shock hazard, the
cord must be plugged into a mating 3-prong
grounding type wall receptacle, grounded in
accordance with the National Electrical Code
and local codes and ordinances. If a mating wall
receptacle is not available, it is the personal
responsibility and obligation of the customer to
have a properly grounded 3-prong wall receptacle
installed by a qualified electrician. See Figure 1
on page 4.
3

Figure 1
3-PRONG
GROUNDING PLUG II
\ 0
\
Q
0 6 !’
GROUND 1
PRONG 3- PRONG
GROUNDING
\ TYPE WALL RECEPTACLE
POWER SUPPLY CORD
ALTERNATE GROUNDING METHOD
If changing and properly grounding the wall
receptacle is impossible and where local codes
permit (consult your electrical inspector), a
temporary adapter may be plugged into the
existing 2-prong wall receptacle to mate with the
3-prong power supply cord. See Figure 2. THIS,
HOWEVER, IS NOT RECOMMENDED.
If this is done, you must connect the grounded
eyelet on the adapter to the wall receptacle
cover plate screw and from this same screw, you
must connect a separate copper ground wire
(#14 minimum) to a grounded cold water pipe.*
See Figure 2. Do not ground to a gas supply
pipe. Do not connect to electrical supply until
appliance is permanently grounded.
GROUND ASSEMBLY
TTACH TO GROUNDED
ELECTRICALLY
GROUNDED MET
COLD WATER PIP
(REMOVE PAINT,
RECEPTACLE
POWER SUPPLY CORD
*Cold water pipe must have metal continuity to
electrical ground and not be interrupted by
plastic, rubber or other electrically insulating
connectors (including water meter or pump)
without adding a jumper wire at these con-
nections.
B
ELECTRICAL
REQUIREMENTS
For 230 volt and 230/208 volt models with serial
plate amperes up through 12.0
Refer to Chart B for specific wiring and receptacle
information to be used.
OBSERVE ALL LOCAL GOVERNING CODES
AND ORDINANCES.
Do not, under any circumstances, remove the
power supply cord ground plug.
ELECTRICAL GROUND IS REQUIRED ON
THIS APPLIANCE.
A three-wire, single-phase 60 hertz AC only
electrical supply is required.
A separate electrical supply is required on a
separately fused circuit. Do not fuse ground-
neutral.
See Chart 6 for receptacle voltage require-
ments, proper fuse size, wire and wiring con-
nections which must conform with rating of
the appliance. Do not use an extension cord.
Chart-B
PLUG AND
RECEPTACLE
DATA
RECEPTACLE
USE TIME-DELAY
FUSE
OR TIME
DELAY CIRCUIT
BREAKER
RATING IN
AMPS
da
@
15
RECEPTACLE
SERIAL PLATE
SERIAL PLATE
OF 230 VOLTS
SERIAL PLATE
MINIMUM
RECEPTACLE
I
TYPE
WIRE SIZE OF BRANCH
CIRCUIT
SEE BELOW
.
1
14 GAUGE
I
SINGLE
OUTLET
USE COPPER ONLY
WIRE ONLY

RECEPTACLE WIRING
RECEPTACLE WIRING should be at least as
large as size shown on electrical Chart B. Use
copper wire only. It is the personal responsibility
and obligation of the customer to provide proper
and adequate receptacle wiring installed by a
qualified electrician. OBSERVE NATIONAL
ELECTRICAL CODE AND ALL LOCAL
GOVERNING CODES AND ORDINANCES.
RECOMMENDED GROUNDING METHOD
Chart-C
For your personal safety, this appliance must be
grounded. This appliance is equipped with a
power supply cord having a 3-prong grounding
plug. To minimize possible shock hazard, the
cord must be plugged into a mating 3-prong
grounding type wall receptacle, grounded in
accordance with the National Electrical Code
and local codes and ordinances. If a mating wall
receptacle is not available, it is the personal
responsibility and obligation of the customer to
have a properly grounded 3-prong wall receptacle
installed by a qualified electrician,
PLUG AND
RECEPTACLE
DATA
RECEPTACLE
VOLTAGE
(60 HERTZ
AC IN ALL
INSTANCES)
RECEPTACLE
MODEL WITH
SERIAL PLATE
OF 230 VOLTS
SERIAL PLATE
OF 2301206
For 230 volt and 230/208 volt models with serial
plate amperes up through 16.0
Refer to Chart C for specific wiring and recep-
tacle information to be used.
OBSERVE ALL LOCAL GOVERNING CODES
AND ORDINANCES.
Do not, under any circumstances, remove the
power supply cord ground plug.
ELECTRICAL GROUND IS REQUIRED ON
THIS APPLIANCE.
A three-wire, single-phase 60 hertz AC only
electrical supply is required.
A separate electrical supply is required on a
separately fused circuit. Do not fuse ground-
neutral.
See Chart C for receptacle voltage require-
ments, proper fuse size, wire and wiring con-
nections which must conform with rating of
the appliance. Do not use an extension cord.
FLAT BLADE GROUND
PRONG
SERIAL PLATE
AhlPERES
VOLTS
(197.6 MIN
253 MAX ) I
up
through
16.0
USE TIME-DELAY
FUSE
OR TIME
DELAY CIRCUIT
BREAKER
RATING IN
AMPS
MINIMUM
RECEPTAC
WIRE SIZE
TYPE I
:LE 1 OF BRANCH
CIRCUIT I
I
RECEPTACLE WIRING
RECEPTACLE WIRING should be at least as
large as size shown on electrical Chart C. Use
copper wire only. It is the personal responsibility
and obligation of the customer to provide proper
and adequate receptacle wiring installed by a
qualified electrician. OBSERVE NATIONAL
ELECTRICAL CODE AND ALL LOCAL
GOVERNING CODES AND ORDINANCES.
5

Chart-D
RECOMMENDED GROUNDING METHOD
For your personal safety, this appliance must be
grounded. This appliance is equipped with a
power supply cord having a 3-prong grounding
plug. To minimize possible shock hazard, the
cord must be plugged into a mating 3-prong
grounding type wall receptacle, grounded in
accordance with the National Electrical Code
and local codes and ordinances. If a mating wall
receptacle is not available, it is the personal
responsibility and obligation of the customer to
have a properly grounded 3-prong wall receptacle
installed by a qualified electrician.
ELECTRICAL
REQUIREMENTS
PLUG AND
RECEPTACLE
DATA
RECEPTACLE _
USE TIME-DELAY
FUSE
OR TIME
DELAY CIRCUIT
BREAKER
RATING IN
AMPS
10 GAUGE
,..rnT
rrm,.
SINGLE
TYPE OUTLET
ONLY USE COPPER
30 WIRE ONLY ONLY
. . I
RECEPTACLE
VOLTAGE
(60 HERTZ
AC IN ALL
INSTANCES)
MODEL WITH
SERIAL PLATE
OF 230 VOLTS
(207 MIN,253
MAX.)
MODEL WITH
SERIAL PLATE
OF 230/208
VOLTS
(197.6 MIN-
253 MAX,)
MINIMUM
RECEPTACLE
WIRE SIZE
SEE BELOW
SERIAL PLATE
AMPERES I
“P
--I
through
24.0
OF BRANCH
For 230 volt and 230/208 volt models with
serial plate amperes up through 24.0
Refer to Chart D for specific wiring and recep-
tacle information to be used.
OBSERVE ALL LOCAL GOVERNING CODES
AND ORDINANCES.
Do not, under any circumstances, remove the
power supply cord ground plug.
ELECTRICAL GROUND IS REQUIRED ON
THIS APPLIANCE.
A three-wire, single-phase 60 hertz AC only
electrical supply is required.
A separate electrical supply is required on a
separately fused circuit. Do not fuse ground-
neutral.
See Chart D for receptacle voltage require-
ments, proper fuse size, wire and wiring
connections which must conform with rating of
the appliance. Do not use an extension cord.
RECEPTACLE WIRING
RECEPTACLE WIRING should be at least as
large as size shown on electrical Chart D. Use
copper wire only. It is the personal responsibility
and obligation of the customer to provide proper
and adequate receptacle wiring installed by a
qualified electrician. OBSERVE NATIONAL
ELECTRICAL CODE AND ALL LOCAL
GOVERNING CODES AND ORDINANCES.
RECOMMENDED GROUNDING METHOD
For your personal safety, this appliance must be
grounded. This appliance is equipped with a
power supply cord having a 3-prong grounding
plug. To minimize possible shock hazard, the
cord must be plugged into a mating 3-prong
grounding type wall receptacle, grounded in
accordance with the National Electrical Code
and local codes and ordinances. If a mating wall
receptacle is not available, it is the personal
responsibility and obligation of the customer to
have a properly grounded 3-prong wall receptacle
installed by a qualified electrician.

INSTALLATION INSTRUCTIONS
for Your Air Conditioner
Through-the-wall
Installation Instructions
for installing the unit in a pre-installed cabinet.
1
l Unpack accessory parts (see Figure 3) be-
fore installing your air conditioner.
Figure 3
CAUTION:
l Be sure air conditioner does not fall
during installation.
l Handle the air conditioner with care.
Watch out for the sharp metal fins on
the front and rear coils.
l Do not use the water condensate for
drinking purposes. It is not sanitary.
PLASTIC
DRAIN
SPOUT
USED ON $
MODELS
WITH DRAIN
CUP AND WEATHER
HOLE IN SEAL USED
REAR
CABINET ON 18 3/4”-
RAIL HIGH
CABINETS
ONLY
0
SEAL
STRIP
(Ya” x X”
( Some
Models)
2
l Pick the right wall. First, decide what room(s)
you want to cool. Then choose a wall that
will allow the air-conditioned air to flow
freely and directly into the room(s) you want
cooled. Remember, it’s difficult to move air
around corners. Choose a location that’s
also near an electrical outlet. (Refer to
ELECTRICAL REQUIREMENTS for re-
ceptacle and wiring needed.) Do not use an
extension cord. (CAUTION: DO NOT LOCATE
AIR CONDITIONER WHERE PLASTIC
CABINET FRONT WILL BE EXPOSED TO
A HEAT SOURCE THAT RAISES THE
SURFACE TEMPERATURE IN EXCESS
OF 120” F.)
_
7

.:_ _ -‘a -.:<!za~a <-‘1’ ! ,uw”+we*A-
3
l Choose the type of decorative molding you
want to use around the room side of the
cabinet. Your choice affects the finish frame
alignment with the inside wall. When using a
wood, metal or plastic molding, the finish
frame should almost line up with the inside
wall. If the wall is plastered to the cabinet
and no molding is used, the finish frame
must be set into the wall by l/2” (see Figure 4
for frame construction or Figure 5 for brick
veneer construction). Cut through two studs
for support.
‘IDE I’,,. CLEARANCE
FOR SERVICE CORD
ENTR” ON LEFT SIDE
APPROPRIATE
NEADER IF CONSTR”CTlON “SE ,,*,,a DIMENSION
REOUIRED ON 2,‘,qi CABINET
APPROPRIATE USE ,I’,,. DIMENSION
Figure 5
ON 23’lw CABINET
PRO”,DE I’,,< CLEARAN
FOR SERVICE CO
ENTRY ON LEFT SI RICK VENEER
ONSTRUCTION
APPROPRIATE /
HEADER IF
REOUIRED
4 . Provide an opening through the wall for a
finish frame. Observe all local governing codes
and ordinances. For wall opening dimensions,
use those shown in Figure 6 and add wood
frame thickness (use 1” lumber or heavier).
When determining finish frame thickness,
be sure you do not cover side cabinet louvers.
A 4” minimum clearance between sidecabinet
louvers and adjoining wall allows for proper
airflow into air conditioner.
Figure 6
TNlS DIMENSION
DEPENDS ON WALL
TNICKNESS AND SED
“SE 26% DIMENSION
CABINET 18% HIGH
“SE 17v2 DIMENSION FOR
(INCLUDES ALLOWANCE FOR
‘1.. FLANGE ON BOl7OM OF
..I
CABINET.)
5
l Construct finish frame. Apply creosote or
something equal to the outside exposed
surface.
6
. Install the finish frame in the wall opening.
Square and level frame and nail it securely to
the studs.
7
l Remove front panel by pushing top down and
out. This protects the panel from damage and
makes the air condtioner easier to handle
during installation (see Figure 7).
8
l Slide unit out of cabinet. First, disconnect the
green ground wire at the left-front corner of
base unit by removing retaining screw (save
screw for reuse later). Now slide unit out of
cabinet by pulling on handle at bottom (see
Figure 7).
9
. Insert exterior cabinet through wall opening.
Leave l-3/16” minimum projection into the
room at service cord exit hole in cabinet, after
allowing for trim. For proper outward water
drainage, shim or reposition cabinet to pro-
vide the proper downward tilt to the outside
(l/2” bubble or l/4” and side-to-side leveling.
10 l Fill all spaces between cabinet and finish
frame with insulation.
8

11
l Drill holes in the cabinet and attach it securely
to finish frame. Use ten #lO x 1” wood
screws (four screws for each side and two
screws for the top; not included). Do not
overtighten screws or cabinet will distort and
provide a poor air seal between cabinet and
unit.
12 l Insert plastic drain-cup spout and metal holder
(on certain models) into hole at rear of cabinet,
as shown in Figure 8. Spout should be facing
downward through hole. OPTIONAL: During
high humidity, condensate may drip from
the outside of your air conditioner onto the
ground below. If your air conditioner is
installed where this is undesirable, you can
direct the water to a more suitable spot by
simply attaching a 5/8” inside-diameter, thin
walled hose to the drain spout at rear of
cabinet (see Figure 9). On models without
plastic drain cup spout, use flashing as needed
to guide water.
Note the type of drain parts you have. Insert
drain cup according to instructions in Figure 8.
Figure 8
1
PLACE PLASTIC
DRAIN INTO HOLE
IN REAR OF
CABINET WITH
SPOUT DOWN
I
r---l
L-Q,
r-l
INTO METAL I
BRACKET AND
INSERT INTO I’ ’
1
CABINET RAIL
SLOTS I
TYPE 1 1 TYPE 2
Figure 9
I
OUTSIDE 4
ROOM
e
SIDE
13
l If you received one adhesive-backed seal strip
(l/4” x l/2”), remove paper backing from
seal and install on air conditioner as shown in
Figure 10.
Fig1
14
l
Insert air conditioner into cabinet. Do not
push against sharp fins and plastic parts.
Attach green ground wire to the left-front
corner of unit base by using retainer screw
(see Figure 11).
Figure 11
SCREW I GROUND WIRE
Figure 12
BOTTOM WEATHER
SEAL -PRESS UPWARD
(Adhesive side on
bottom of base )
15
l For installation of bottom weather seal on unit
with 18 3/4”-high cabinet, see Figure 12.
16
. Attach front, by placing bottom edge on clips
and pushing top down, then in and up.
17
. Caulk all outside wall openings around cabinet.
18 l If needed, install molding around room side
of cabinet.
9

HOW TO START AND USE
YOUR AIR CONDITIONER
To Start Your Air Conditioner
EXHAUST CONTROL
FAN SPEED/
HEAT CONTROL
THERMOSTAT CONTROL
Be sure air conditioner is OFF before plugging
it in.
1
l Set exhaust control (if your unit is so equip-
ped) to OFF for maximum cooling or heating.
2 l Choose a fan speed setting for cooling or
heating.
LO COOL . . . . . . . . . for sleeping comfort
HI COOL . . . . . . for maximum cooling
LO HEAT.. . . . for reduced air movement
with heat
HI HEAT . . . for maximum air movement
with heat
3
0
Turn thermostat control to Number 6 (mid-
setting). You can adjust the air conditioner’s per-
formance by resetting the thermostat control to
a higher number for maximum cooling. Lower the
number setting for less cooling. You will need to
experiment to find the setting which suits you
best.
10