Whirlpool R1011 Product information sheet

ROOMAIRCONDITIONER
InstallationInstructionsand
Use&CareGuide
R

Contents
Page
Important Safety Instructions ........................ .2
Electrical Requirements .................................. 3
Installation Instructions .................................. 8
Window installation - A .................................. 9
Window installation - B ................................ 12
Through-the-wall installation ........................ 17
Operating Instructions .................................. 20
Starting your air conditioner ........................ .20
The ENERGY SAVER settings ................... .20
The exhaust control ..................................... .21
Changing air direction .................................. 22
Cleaning Instructions ................................... .22
Cleaning front panel and filter ...................... 22
Maintenance Instructions ............................. 23
Annual maintenance .................................... 23
Oiling the fan motor ...................................... 25
Energy saving tips ........................................ 25
If You Need Service Or Assistance ............. .28
Thank you for buying this appliance. Please
complete the form below. Have this information
ready if you need service or call with a question.
l Copy model and serial numbers from label (see
diagram below) and purchase date from sales
slip.
l Keep this book and sales slip together in a
handy place.
Model Number
Serial Number
Purchase Date
Service Company Phone Number
I
seri Model and al number
label
ImportantSafety
Instructions
To reduce the risk of fire, electrical shock
Dr personal injury when using your air
conditioner, follow these basic precau-
tions:
bRead all instructions before using your
air conditioner.
mComplete the installation requirements
as described in “Installation Instructions”
on pages 8-l 9.
l Never allow children to operate or play
with the air conditioner.
l Do not operate the air conditioner with
the front panel removed.
. Never clean air conditioner parts with
flammable fluids. The fumes can create a
fire hazard or explosion.
l FOR YOUR SAFETY ’
DO NOT STORE OR USE GASOLINE OR
OTHER FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF THIS OR ANY
OTHER APPLIANCE. THE FUMES CAN
CREATE A FIRE HAZARD OR EXPLOSION.
It is your responsibility to be sure your air
conditioner:
l Is installed in a window or wall that will hold
the weight, and is secured according to the
Installation Instructions.
l Is connected only to the proper kind of
outlet, with the correct electrical supply and
grounding. (See “Electrical Requirements”
on pages 3-7.)
l Is the correct size for the area you want to
cool.
l Is used only for the job it was designed to
do.
l Is not used by children or anyone unable to
operate it properly.
l Is properly maintained.
Also, remove Energy Label and Buy Guide.
Use a damp cloth to take off any glue residue.
Do not use sharp instruments, flammable
fluids or abrasive cleaners. These can
damage the material.
- SAVE THESE INSTRUCTIONS -
2

ElectricalRequirements
Below are electrical plug variations, choose the
one which matches the ampere rating of your
unit. Your model’s ampere rating is printed on the
model and serial number label, attached to the
unit, behind the front panel. (See diagram on
we 2.1
OBSERVE ALL LOCAL CODES AND ORDI-
NANCES.
DO NOT USE AN EXTENSION CORD WITH
THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES,
REMOVE THE POWER SUPPLY CORD
GROUNDING PRONG.
Electrical Shock and Fire Hazard
) Check with a qualified electrician if you
are in doubt as to whether the appliance
is properly grounded. Do not modify the
power supply cord plug - if it will not fit
the outlet, have a proper outlet installed
by a qualified electrician. Improper
connection of the equipment-grounding
conductor can result in a risk of electrical
shock.
* Do not use an extension cord with this
appliance. Such use may result in fire,
electrical shock or other personal injury.
l Do not have a fuse in the neutral or
grounding circuit. This could result in a
risk of electrical shock.
ELECTRICAL REQUIREMENTS SEE PAGE
115 volt models with amperes up
through 12.0
230 and 230/208 volt models with
amperes up through 12.0
230 and 230/208 volt models with
amperes up through 16.0
230 and 230/208 volt models with
amperes up through 24.0
4
55
6
7

Electrical Requirements
Continued
115volt modelswith amperes
-
upthrough12.0
Receptacle wiring
Receptacle wiring should be a minimum of
14 gauge. Use copper wire only. It is the respon-
sibility of the consumer to provide proper and
adequate receptacle wiring, installed by a
qualified electrician. Observe National Electrical
Code and all local governing codes and ordi-
nances.
Electrical requirements
A 115 volt (103.5 min., 126.5 max.), 60 Hz, AC
only, 15 ampere fused electrical supply is
required (time delay fuse or time delay circuit
breaker required). For models with serial plate
amperes of 7.6 through 12, it is required that a
separate circuit, serving only this appliance, be
provided.
Electrical connection
II Electrical ground is required on this appliance.
Recommended grounding method:
3prong
For your personal safety, this appliance must be
grounding
grounded. This air conditioner is equipped with a
Plug
%v-
8
!’
power supply cord having a 3-prong grounding
prong. To minimize possible shock hazard, the
cord must be plugged into a mating 3-prong
Grounding
grounding type wall receptacle, grounded in
prong
4
3prong
accordance with the National Electrical Code and
grounding
type wall
local codes and ordinances. If a mating wall
receptacle
receptacle is not available, it is the responsibility
of the customer to have a properly grounded
Power
W$lY
3-prong wall receptacle installed by a qualified
electrician.

230and230/208volt models
with amperesupthrough12.0
Receptacle wiring
Receptacle wiring should be a minimum of
14 gauge. Use copper wire only. It is the respon-
sibility of the consumer to provide proper and
adequate receptacle wiring, installed by a
qualified electrician. Observe National Electrical
Code and all local governing codes and ordi-
nances.
Electrical requirements
A 230 volt (207 min., 253 max.), 60 Hz, AC only,
15 ampere fused electrical supply is required
(time delay fuse or time delay circuit breaker
required). It is required that a separate circuit,
serving only this appliance, be provided.
OR
A 230/208 volt (197.6 min., 253 max.), 60 Hz, AC
only, 15 ampere fused electrical supply is
required (time delay fuse or time delay circuit
breaker required). It is required that a separate
circuit, serving only this appliance, be provided.
Electrical connection
d-prong
grounding
type wall
receptacle
Electrical ground is required on this appliance.
Recommended grounding method:
For your personal safety, this appliance must be
grounded. This air conditioner is equipped with a
power supply cord having a 3-prong grounding
prong. To minimize possible shock hazard, the
cord must be plugged into a mating 3-prong
grounding type wall receptacle, grounded in
accordance with the National Electrical Code and
local codes and ordinances. If a mating wall
receptacle is not available, it is the responsibility
of the customer to have a properly grounded
3-prong wall receptacle installed by a qualified
electrician.
prong
3-prong
grounding
plug

Electrical Requirements
Continued
230and230/208volt models
with amperesupthrough16.0
Receptacle wiring
Receptacle wiring should be a minimum of
12 gauge. Use copper wire only. It is the respon-
sibility of the consumer to provide proper and
adequate receptacle wiring, installed by a
qualified electrician. Observe National Electrical
Code and all local governing codes and ordi-
nances.
Electrical requirements
A 230 volt (207 min., 253 max.), 60 Hz, AC only,
20 ampere fused electrical supply is required
(time delay fuse or time delay circuit breaker
required). It is required that a separate circuit,
serving only this appliance, be provided.
OR
A 230/206 volt (197.6 min., 253 max.), 60 Hz, AC
only, 20 ampere fused electrical supply is
required (time delay fuse or time delay circuit
breaker required). It is required that a separate
circuit, serving only this appliance, be provided.
Electrical connection
Power
SuPPlY 3-prong
grounding
type wall
Electrical ground is required on this appliance.
Recommended grounding method:
For your personal safety, this appliance must be
grounded. This air conditioner is equipped with a
power supply cord having a 3-prong grounding
prong. To minimize possible shock hazard, the
cord must be plugged into a mating 3-prong
grounding type wall receptacle, grounded in
accordance with the National Electrical Code and
local codes and ordinances. If a mating wall
receptacle is not available, it is the responsibility
of the customer to have a properly grounded
3-prong wall receptacle installed by a qualified
electrician.

Sprang
grounding
type wall
receptacle
230and230/208volt models
with amperesupthrough24.0
Receptacle wiring
Receptacle wiring should be a minimum of
10 gauge. Use copper wire only. It is the respon-
sibility of the consumer to provide proper and
adequate receptacle wiring, installed by a
qualified electrician. Observe National Electrical
Code and all local governing codes and ordi-
nances.
Electrical requirements
A 230 volt (207 min., 253 max.), 60 Hz, AC only,
30 ampere (cartridge type) fused electrical supply
is required (time delay fuse or time delay circuit
breaker required). It is required that a separate
circuit, serving only this appliance, be provided.
OR
A 230/206 volt (197.6 min., 253 max.), 60 Hz, AC
only, 30 ampere (cartridge type) fused electrical
supply is required (time delay fuse or time delay
circuit breaker required). It is required that a
separate circuit, serving only this appliance, be
provided.
Electrical connection:
Electrical ground is required on this appliance.
Recommended grounding method
For your personal safety, this appliance must be
grounded. This air conditioner is equipped with a
power supply cord having a 3-prong grounding
prong. To minimize possible shock hazard, the
cord must be plugged into a mating 3-prong
grounding type wall receptacle, grounded in
accordance with the National Electrical Code and
local codes and ordinances. If a mating wall
receptacle is not available, it is the responsibility
of the customer to have a properly grounded
3-prong wall receptacle installed by a qualified
electrician.
Power
WJdp’Y
7

nstallation nstructions
Unpack the accessory parts that came with your
air conditioner to determine which installation
instructions you should follow. Use the chart
below as a guide.
IF YOU HAVE THESE PARTS FOLLOW THESE INSTRUCTIONS
Gum-type sealer
Qmil
Window lock Top mountino
channel >
-
(38” wi&)
tj qy;-&.
(5) Round-head
wood screws
metal screws EPrPlllC ,113nyj 2”) (#e x 3,d.t)
-OR-
For through-the-wall installation
“Window installation - A” on page 9.
“Window installation - B” on page 12.
“Through-the-wall installation” on page 17
8

Windowinstallation -A
Gum-type sealer
am
To help avoid any installation problems and to
help ensure trouble-free performance of your new
air conditioner, read these installation instruc-
tions, as well as your operating instructions and
electrical requirements before installing your unit.
Personal Injury and Product Damage
Hazard
l Because this air conditioner weighs about
75 to 125 pounds, it is recommended that
you have someone help you install your
new unit and that you both use proper
lifting techniques.
. Inspect the condition of the window
where the air conditioner will be installed.
Be sure it will support the weight of the
unit.
. This appliance must be installed accord-
ing to all applicable codes and ordi-
nances.
l Handle the air conditioner with care.
Watch out for the sharp metal fins on the
front and rear coils.
. Be sure your air conditioner does not fall
during installation.
. Do not use the water collected in unit for
drinking purposes. It is not sanitary.
Failure to follow the above precautions
could result in personal injury or product
damage.
1. Unpack accessory parts before installing
your air conditioner. Make sure you have all
the necessary parts. A normal installation can
be made with a screwdriver, small level,
pocket knife, tape measure, a drill and 3/32”
drill bit.
9

Installation Instructions
Continued
Level
2. Pick the right window. First, decide what
room(s) you want to cool. Then choose a
window that will allow the air-conditioned air to
flow freely and directly into the room(s) you
want cooled. Remember, it’s difficult to move
air around corners. Choose a window that is
also near an electrical outlet. (See “Electrical
Requirements” on pages 3-7 for receptacle
and wiring needs.) Do not use an extension
cord.
The window in which you place your air
conditioner should have an opening of at least
25 inches in width and at least 16 inches in
height. Standard installation parts are supplied
for double-hung sash windows up to 38 inches
in width.
3. Remove front panel by pushing top of panel
down and out. This protects the panel from
damage and makes the air conditioner easier
to handle during installation.
4. Center air conditioner in window. Rear of
unit must be raised slightly to position lower
rail of air conditioner behind and up against
back side of window sill. Firmly lower the
window sash behind the top mounting
channel.
NOTE: Do not block air entry into the side
louvers of the cabinet.
I
Be sure the cabinet
window during installation.
5. Leveling air conditioner is not required in a
normal installation. The proper slope is
designed into the unit. However, be sure you
have approximately l/2 bubble (l/4”) down-
ward tilt to the outside for proper water
drainage. If necessary, reposition or shim
cabinet to provide the proper tilt or side-to-side
leveling.

Window rail
seal - Window lock
- bracket
6. Pull out sliding curtains while holding air
conditioner in window. Extend curtains on both
sides until they reach the insides of the
window channels. (Pulling curtains slightly
inward allows for easier sliding.)
Mark and drill a pilot hole (3/32”) in each
curtain handle before installing thumb screws.
NOTE: If space is a problem, use the pre-
drilled holes in the top flanges of the curtains
for the thumb screws.
7. Install window rail seal and window lock
bracket. Press foam window rail seal into
place and cut to proper length. Mark and drill a
pilot hole (3/32”), then install window lock
bracket using the round-head screw. Seal
small openings around installation with gum-
type sealer.
Keep window lock bracket installed at all
times to ensure that unit will not fall out of
the window. Remove window lock bracket
only when you wish to remove air condi-
tioner from window.
8. Attach front panel by placing bottom edge on
clips and pushing top down, then up and in.

Installation Instructions
Continued
Windowinstallation - B
Window lock
$p;;nting
hV^^C^I (2) Side A
Foam
To help avoid any installation problems and to
help ensure trouble-free performance of your new
air conditioner, read these installation instruc-
tions, as well as your operating instructions and
electrical requirements before installing your unit.
Personal Injury and Product Damage
Hazard
l Because this air conditioner weighs about
125 to 200 pounds, it is recommended
that you have someone help you install
your new unit and that you both use
proper lifting techniques.
l Inspect the condition of the window
where the air conditioner will be installed.
Be sure it will support the weight of the
unit.
l This appliance must be installed accord-
ing to all applicable codes and ordi-
nances.
l Handle the air conditioner with care.
Watch out for the sharp metal fins on the
front and rear coils.
l Be sure your air conditioner does not fall
during installation.
l Do not use the water collected in unit for
drinking purposes. It is not sanitary.
Failure to follow the above precautions
could result in personal injury or product
damage.
1. Unpack accessory parts before installing
your air conditioner. Make sure you have all
the necessary parts. A normal installation can
be made with a screwdriver, saw, small level,
pocket knife, tape measure, 7/l 6” socket
wrench, drill and 3/32” drill bit.
(4) RounZ (7) He;-head Plastic drain-cup
head sheet sheet metal spout
metal screws screws (#t 0x12”) haad
(Ml x 3/8”) wood
screws
(#El x 3/4”)
12

Ground wme screw ? Handle
2. Pick the right window. First, decide what
room(s) you want to cool. Then choose a
window that will allow the air-conditioned air to
flow freely and directly into the room(s) you
want cooled. Remember, it’s difficult to move
air around corners. Choose a window that is
also near an electrical outlet. (See “Electrical
Requirements” on pages 3-7 for receptacle
and wiring needs.) Do not use an extension
cord.
The window in which you place your air
conditioner should have an opening of at least
26 inches in width and at least 18 inches in
height. Standard installation parts are supplied
for double-hung sash windows up to 40 inches
in width.
3. Remove front panel by pushing top of panel
down and out. This protects the panel from
damage and makes the air conditioner easier
to handle during installation.
4. Slide unit out of cabinet. First, disconnect
the green ground wire at the left-front corner of
base of unit by removing retaining screw (save
screw for reuse in step 14). Now slide unit out
of cabinet by pulling out on handle at base of
unit.
5. Attach seal strips to cabinet. Place
3/a”-wide self-adhesive seal strip on window
side of bottom flange. Now, starting at the
lower corner of the cabinet, apply 3/8”-wide
seal strips over the center line of the pre-
drilled holes for one of the side mounting
angles, over the center line of pre-drilled holes
for the top mounting channel, and over the
center line of pre-drilled holes for the other
side mounting angle.
13

Installation Instructions
Continued
I
Measure distance from inside
one window channel to inside
L* of the other and subtract 114”
\ Front /
6. Attach side mounting angles to the sides of
the cabinet by using 4 hex-head sheet metal
screws. Insert bottom screws first. Be sure
flange of each side mounting angle faces
inside. Now attach top mounting angle to
cabinet by using 3 hex-head sheet metal
screws. Again, be sure tallest flange is facing
inside.
7. Measure and cut filler board to proper sizes.
First, measure the distance from inside one
window channel to the inside of the other
channel and subtract l/4”. Now subtract the
width of the air conditioner and divide by 2.
This will give you the width to cut each filler
board. Be sure to cut the filler board across
the mid-section of its longest measurement.
Because the filler boards will be equal in
width, they will automatically center your air
conditioner in the window.
8. Apply seal strips and attach filler boards.
Determine which will be your left and right filler
boards. The holes on each board should align
with the holes in the side mounting angles.
Each filler board should also extend about l/2”
above the top edge of the air conditioner
cabinet. Now apply 3/a”-wide seal strips on
the room side of each filler board along the
bottom and window channel edges. Now
attach the filler boards to the side mounting
angles with 4 round-headed sheet metal
screws. Tighten the screws only loosely, so
the filler boards can be moved back and forth.
9. Insert side mounting slides all the way into
the top mounting channel.
14

Installation Instructions
Continued
The foam blocks provided are to hold
filler board tight against window
channel. Cut block l/4” wilder than
channel and wedge into place.
, Window channel
must be installed on
both sides
10. Place cabinet in window by turning cabinet
to one side to get one filler board into window
channel. Now maneuver other filler board into
window channel. Reaching through window
opening, push filler boards from outside as far
toward you as they will go. Extend the side
mounting slides outward into the window
channels on both sides. Pull the cabinet
toward you to position the side mounting
slides as far forward in the window channels
as possible. Now, mark and drill a pilot hole
(3/32”) in each side mounting slide for the
wood screws. The screws are used to secure
the side mounting slides into the window
channels. Be sure to use the foam blocks that
are provided.
I
Be sure the cabinet does not fall out of
window. I
11. Lower window and level air conditioner.
Lower the window firmly behind window
gasket. Leveling the cabinet is not required in
a normal installation since the proper slope is
designed into the product. However, be sure
you have approximately a l/2 bubble (l/4”)
downward tilt to the outside for proper water
drainage. If necessary, reposition or shim
cabinet to provide the proper tilt or side-to-
side leveling. Now, tighten all 4 filler board
screws. Be sure cabinet bottom flange is
against rear of window sill for proper seal.
Finally, make 2 pilot holes (3/32”) into the
window sill, using the holes in the cabinet as
a guide. Use 2 wood screws to secure the
bottom of the cabinet to the window sill.
15

Installation Instructions
Continued
12. Install window rail seal and window lock
bracket and drain cup. Press foam rail seal
into place and cut to proper length. Make a
mark and drill a pilot hole (3/32”), then install
lock bracket using a wood screw. Seal small
openings around installation with gum-type
sealer.
Window lock bracket must be installed at
all times to be sure air conditioner does
not fall out of window. Remove only when
you wish to remove air conditioner from
window.
13. Install plastic drain-cup spout into hole
at rear of cabinet. Spout should be facing
downward through hole.
OPTIONAL: During high humidity, condensate
may drip from the outside of your air conditioner
onto the ground below. If your air conditioner is
installed where this is undesirable, you can direct
the water to a more suitable spot by simply
attaching a 5/V inside-diameter, thin walled hose
to the drain spout at rear of cabinet.
14. Insert air conditioner into cabinet. Slide
unit all the way into the cabinet. Do not push
against sharp fins and plastic parts. Attach
green ground wire to the left-front corner of
unit base by using ground wire screw.
Electrical Shock Hazard
Keep wire connected whenever air condi-
tioner is in cabinet. Failure to do so could
result in electrical shock during operation
and maintenance.
15. Attach front panel by placing bottom edge on
clips and pushing top down, then in and up.
16

Through-the-wallinstallation
It is the responsibility and obligation of the
customer to have this product installed by a
qualified technician familiar with through-the-wall
installation.
OR
If you choose to install the air conditioner
yourself, read all installation instructions, as well
as the electrical requirements and operating
instructions before installing your unit. This will
help to avoid any installation problems and will
help ensure trouble-free performance of your new
air conditioner.
Personal Injury and Product Damage
Hazard
l Because this air conditioner weighs about
125 to 200 pounds, it is recommended
that you have someone help you install
your new unit and that you both use
proper lifting techniques.
l Inspect the condition of the wall where
the air conditioner will be installed. Be
sure it will support the weight of the unit.
l This appliance must be installed accord-
ing to all applicable codes and ordi-
nances.
l Handle the air conditioner with care.
Watch out for the sharp metal fins on the
front and rear coils.
l Be sure your air conditioner does not fall
during installation.
l Do not install air conditioner where
plastic cabinet front will be exposed to a
heat source that raises the surface
temperature above 120°F.
l Do not use the water collected in unit for
drinking purposes. It is not sanitary.
Failure to follow the above precautions
could result in personal injury or product
damage.
1. Pick the right wall. First, decide what room(s)
you want to cool. Then choose a wall that will
allow the air-conditioned air to flow freely and
directly into the room(s) you want cooled.
Remember, it’s difficult to move air around
corners. Choose a location that is also near an
electrical outlet. (See “Electrical Require-
ments” on pages 3-7 for receptacle and wiring
needs.) Do not use an extension cord.
17

Installation Instructions
Continued
Appropriate
header if
required \
E louvers
Plast
Alternate 1 ; \\‘\A\ ‘1 Finish
I frame
Do not
block
thickness
Provide 1 %6
Appropriate ’ \ Use 11 ,9/~6”
header if required CONSTUCTION
dimensionon
23 ‘/ie” cabmet
Appropriate Use 11 %6”
header if dimension on
required \ / 23 ‘/rs” cabinet
for plaster
Provide 1 VIS”
clearance for service
cord entry on left
side /- 81
_I RICK VENEER
/ L.ONSTRUCTION
Appropriate /
header if reauired
(includes allowance for ‘/16” flange
on bottom of cabinet.)
2. Choose the type of decorative molding you
want to use around the room side of the
cabinet. ‘tour choice affects the finish frame
alignment with the inside wall. When using a
wood, metal or plastic molding, the finish
frame should almost line up with the inside
wall. If the wall is plastered to the cabinet and
no molding is used, the finish frame must be
set into the wall by l/2”. (See top figure at left
for frame construction. See middle figure at
left for brick veneer construction.) Cut through
two studs for support.
3. Provide an opening through the wall for a
finish frame. Observe all local governing
codes and ordinances. For wall opening
dimensions, use those shown at left and add
wood frame thickness (use 1” lumber or
heavier). When determining finish frame
thickness, be sure you do not cover side
cabinet louvers. A 4” minimum clearance
between side cabinet louvers and adjoining
wall allows for proper airflow into air condi-
tioner.
4. Construct finish frame. Apply creosote (or an
equivalent) to the outside exposed surface.
5. Install finish frame in the wall opening.
Square and level frame and nail it securely to
the studs.
6. Remove air conditioner front panel by
pushing top down and out. This protects the
panel from damage and makes the air
conditioner easier to handle during installation.
18

Ground wire screw F
Screw I Ground wire
7. Slide unit out of cabinet. First, disconnect
the green ground wire at the left-front corner
of base unit by removing retaining screw
(save for reuse in step 12). Now slide unit out
of cabinet by pulling on handle at base of
unit.
8. Insert exterior cabinet through wall
opening. Leave l/2” minimum overhang into
the room at top of cabinet, after allowing for
trim. For proper outward water drainage, shim
or re-position cabinet to provide the proper
downward tilt to the outside (l/2 bubble or 1”)
and side-to-side leveling.
9. Fill all spaces between cabinet and finish
frame with insulation.
10. Drill holes in the cabinet and attach it
securely to finish frame. Use IO #I 0 x 1”
wood screws (4 screws for each side and 2
screws for the top - screws are not included).
Do not overtighten screws or cabinet will
distort and provide a poor air seal between
cabinet and unit.
11. Inset-t air conditioner into cabinet. Do not
push against sharp fins and plastic parts.
12. Attach green ground wire to the left-front
corner of unit base by using retainer screw.
Electrical Shock Hazard
Keep wire connected whenever air condi-
tioner is in cabinet. Failure to do so could
result in electrical shock during operation
and maintenance.
13. Attach front panel by placing bottom edge
on clips and pushing top down, then in and
up.
14. Caulk all outside wall openings around
cabinet.
15. If needed, install molding around room side
of cabinet.
16. OPTIONAL: During high humidity, conden-
sate may drip from the outside of your air
conditioner onto the ground below. If your air
conditioner is installed where this is undesir-
able, you can direct the water to a more
suitable spot by simply attaching a 5/8”
inside-diameter, thin walled hose to the drain
spout at rear of cabinet (see figure at left). On
models without plastic drain-cup spout, use
flashing as needed to guide water.
NOTE: Now refer to “Electrical Requirements” on
pages 3-7 and “Starting your air conditioner” on
page 20.
19