Whirlpool SPOW 407 User manual

Gebrauchsanweisung
Instructions for use
Mode d’emploi
Gebruiksaanwijzing
Istruzioni per l’uso
Brugsanvisning
Bruksanvisning
Käyttöohje
Manual de utilização
Instrucciones para el uso
Instrukcje użytkowania
Használati utasítás
ИнструкциЯза употреба
Návod k použití
Návod na použitie
Instruc∑iuni de utilizare
Инструкции по эксплуатации

3
SPOW 407, SPOW 409, SPOW 412, SPOW 418
ENGLISH Instructions for use Page 4
FRANÇAIS Mode dʼemploi Page 29
РУCCКИЙ Инcтpyкции по экcплyaтaции Cтpaницa 54
УКРАЇНСЬКА Інструкція з експлуатації Сторінка 79
4




 


BEFORE USING THE APPLIANCE
Please ready all instructions carefully before using this product. When using this appliances, should always
follow this instruction to reduce the risk of fire, electric shock, and injury to person.
Please keep this manual. If you deliver the appliance to other users, do handover this manual together.
These instructions shall also be available on website: www.whirlpool.eu.
SAFETY PRECAUTIONS
•The Installation and service/repair
must be performed by a qualified
technician, in compliance with the
producer's instructions and
following local safety norms. Do
not repair or replace any parts of
the appliance unless it is
specifically written in the user
instructions.
•Do not pull the power supply
cord to remove it from the
socket. Do not twist or press the
power supply cord, and make
sure it is not broken.
•Do not touch the power plug,
circuit breaker and emergency
button when your hands are wet.
•Do not insert your fingers or
foreign substances into the air
inlet/outlet of indoor&outdoor
unit.
•Never block the air inlet or outlet
of indoor and outdoor unit.
•Physically or mentally disabled
people, children and people
without any experience with the
product are only allowed to use
the appliance if they have had
specific training on how to
operate the appliance by a person
responsible for their security and
well-being. The appliance is not
intended for use by disabled
people and very young children
without supervision.
•Children should be supervised to
ensure that they do not play with
the appliance (including remote
control).
•This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance in
a safe way and understand the
hazards involved. Children shall
not play with the appliance.
Cleaning and user maintenance
shall not be made by children
without supervision.
4

• This appliance has been made of recyclable or
re-usable material. Scrapping must be carried
out in compliance with local waste disposal
regulations. Before scrapping it, make sure to
cut off the mains cord so that the appliance
cannot be re-used.
• For more detailed information on handling and
recycling of this product, contact your local
authorities who deal with the separate collection
of rubbish or the shop where you bought the
appliance.
SCRAPPING OF PACKAGING
• The packaging can be 100% recycled as
confirmed by the recycling symbol . The
various parts of the packaging must not be
dispersed in the environment, but must be
scrapped in line with local authority regulations.
SCRAPPING OF APPLIANCE
• This appliance is marked according to the
European Directive 2002/96/EC, Waste
Electrical and Electronic Equipment (WEEE).
• By ensuring that this product is disposed of
correctly, you will help to prevent potentially
negative consequences for the environment and
for human health.
• The symbol on the product or on the
documents accompanying the product indicates
that this appliance should not be treated as
household waste, but must be given to the
appropriate local gathering place where electric
and electronic appliances are stored and
recycled.
SAFEGUARDING THE ENVIRONMENT
5
AIR CONDITIONER PRECAUTIONS
Please strictly follow the below
instructions:
•Long and direct exposure to cool
air might be harmful to health. It is
advisable to set the louvers in
order to avoid direct cool air and
deflect it within the room.
•Upon malfunctioning first turn the
appliance off by pressing the
ON/OFF button on the remote
control, then disconnect it from
power supply.
•Always turn off the air conditioner
by remote control first. Do not
use the power supply circuit
breaker or pull off the plug to turn
it off.
•Do not switch the appliance on
and off too often as this can
damage the appliance.
•Do not place any objects on the
outdoor unit.
•Disconnect the air conditioner
from the power supply if it is to
be left unused for a long period of
time or during a thunder/lightning
storm.
•This product contains Fluorinated
Greenhouse Gases covered by the
Kyoto Protocol, the refrigerant
gas being in a hermetically sealed
system. Refrigerant gas: R410a has
a Global Warming Potential
(GWP) 2087.5.

Images in the user instructions are based on external views of standard models, shape and design vary
according to the model.
6
PRODUCT DESCRIPTION
Indoor unit
1. Air Intake
2. Front Panel
3. Display panel
4. Air Outlet
5. Electrical box
6. Filter reset button
7. Vertical Adjustment Louver
8. Horizontal Adjustment Louver
9. Air Filter
10. Remote Control
11. On-off Switch
Outdoor unit
12. Air Intake
13. Pipes and Power Connection Cord
14. Drain Hose
Note: Condensate water drains at COOLING or
DRY operation.
15. Air Outlet
Outdoor unit
Indoor unit

7
CONTROL PANEL DISPLAY INDICATORS
DESCRIPTION
Temperature indicator (1)
Displays set temperature.
It shows "FC" as a reminder to clean the filter.
Running indicator (2)
It lights up during operation.
It flashes during outside unit defrosting.
Timer indicator (3)
It lights up during the set time.
It goes off when timer operation ends.
Sleep indicator (4)
It lights up once sleep mode is set, "Running" indicator will flash for 10 times then the whole display
will light off.
Filter monitor indicator (5)
It flashes when the filter needs to be cleaned.
Filter monitor indicator flashes after 200 hours of usage as reminder to clean the filter.
After filter cleaning, press the filter reset button located on the indoor unit behind the front panel in
order to interrupt the flashing of the filter monitor indicator.

8
REMOTE CONTROL FUNCTIONS
AND INDICATORS
1. ON/OFF BUTTON
Starts and/or Stops the appliance by pressing
this button.
2. MODE BUTTON
Used to select the operation mode.
3. FAN BUTTON
Used to select fan speed in sequence auto,
high, medium or low.
4-5.TEMPERATURE BUTTON
Used to select the room temperature. Used
to set time in timer mode and real time clock.
6. 6TH SENSE BUTTON
Sets or cancels 6th sense operation.
7. SWING BUTTON
Stops or starts horizontal adjustment louver
swinging and sets the desired up/down airflow
direction.
8. SLEEP BUTTON
Sets or cancels Sleep Mode operation.
9. AROUND U BUTTON
Used to set or cancel Around U function.
10. TIMER ON/CLOCK BUTTON
Used to set the current time.
Used to set or cancel the timer on operation.
11 TIMER OFF BUTTON
Used to set or cancel the timer off operation.
12. JET BUTTON
Used to start or stop the fast cooling or
heating.
13. DIM BUTTON
Used to turn on or turn off display light on
indoor unit.
14. POWER SAVE BUTTON
Used to start or stop the power save
operation.
INDICATOR SYMBOLS ON RC DISPLAY
Cooling indicator
Dry indicator
Fan only indicator
Heating indicator
Auto fan speed
High fan speed
Medium fan speed
Low fan speed
6th Sense indicator
Sleep indicator
Around U indicator
Jet indicator
Signal transmission
Display set timer
Display current time
Display set temperature
Power save indicator
OON
OFF

STORAGE AND TIPS FOR USING THE
REMOTE CONTROL
How to insert the batteries
1. Insert a pin and gently press down on the
battery cover and push in the direction of the
arrow to remove, as shown.
2. Insert 2 AAA batteries (1.5V) into the
compartment.
Ensure that "+" and "-" polarity is correctly
positioned.
3. Close the battery cover on the remote control.
How to remove the batteries
Remove the battery cover in the direction of the
arrow.
Press the positive pole of the battery softly with
your fingers, then draw the batteries out of the
compartment. All this should be done by adults,
children are forbidden to remove the batteries
from the remote control in order to avoid danger
of swallow.
Disposal of the batteries
To protect natural resources and to promote
material reuse, please separate batteries from
other types of waste and recycle them through
your local, free battery return system.
Precautions
• When replacing the batteries, do not use new
batteries with old batteries, or different types of
batteries as this may cause the remote control
to malfunction.
• If you do not expect to use the remote control
for some time, take the batteries out to prevent
leakage of battery acid in the remote control.
• Operate the remote control within effective
range. Keep the remote control at least 1 meter
from any TV set or HI-FI equipment.
• If the remote control does not work normally,
take the batteries out and reinstall after 30
seconds. If it still does not work install new
batteries.
• To operate the appliance by remote control,
point the remote control at the receiving device
on the indoor unit, to ensure receiving
sensibility.
• To send a message from remote control, the
symbol will flash for 1 second. On receipt
of the message, the appliance will emit a beep.
• The remote control will operate the air
conditioner at a distance of up to 7m.
• Each time the batteries are replaced in the
remote control, the remote control is pre-set at
Heat Pump mode.
Signal receptor
9

10
OPERATING MODE DESCRIPTION
Operation Modes:
1. Selecting mode
Each time MODE button is pressed, the operation
mode is changed in sequence:
COOLING →DRY →FAN ONLY →HEATING
↑
Heating mode is not available for cooling only air
conditioners.
COOLING mode: used to cool your room to let
you feel cool and comfort in the hot season.
DRY mode: used to remove moisture to let you
feel comfort in a humid climate.
FAN ONLY mode: used to ventilate your room,
the air conditioner operates like a fan.
HEATING mode: used to heat your room to let
you feel warm in the cold season.
Note: In order to prevent cool air blowing, 2-5
minutes are necessary to preheat the indoor unit
at HEATING operation start. The indoor fan will
not work during preheating.
2. Setting fan speed
Each time the "FAN" button is pressed, the fan
speed is changed in sequence:
Auto →High →Medium →Low
↑
At "FAN ONLY" mode, only "High","Medium" and
"Low" are available.
At "DRY" mode, Fan speed is set at "Auto"
automatically, "FAN" button is ineffective in this
case.
3. Setting temperature
Press once to raise temperature setting by 1
raise °C
Press once to lower temperature setting by 1
lower °C
Press these two button and hold consistently,
you can change the number quickly.
*Note: Heating mode is NOT available for
cooling only models.
4. Turning on
Press button, when the appliance receives
the signal, the RUNNING indicator of the indoor
unit lights up.
During mode changes wait a few seconds and
repeat the operation if the unit does not respond
at once.
When selection the heating operation, air flow will
start after 2-5 minutes.
Range of available set temperature
*HEATING, COOLING 18°C~32°C
DRY +/-2°C
FAN ONLY unable to set
4
1 2
3

11
AIRFLOW DIRECTION CONTROL
5. Airflow direction control
Horizontal airflow is automatically adjusted to a
certain angle in accordance with the operation
mode after turning on the unit.
The direction of airflow can be also adjusted to
your own requirement by pressing the "SWING"
button of the remote control.
*Heating mode is only available for heat pump
models.
Horizontal airflow control (using the remote
control)
Use the remote control to set the flow angles.
Swinging airflow
Pressing "SWING" button once, the horizontal
adjustment louver will swing up and down
automatically.
Desired direction airflow
Pressing the "SWING" button again to hold the
horizontal adjustment louver when the louvers
swing to a suitable angle as desired.
Vertical airflow control (by hands)
Turn the control rods of the vertical adjustment
louvers to change vertical air flow as shown.
Note: The shape of the unit may look different
from that of the air conditioner you have selected.
A - Do not turn the horizontal adjustment louvers
manually, otherwise malfunction may occur. If
that happens, turn off the unit first and cut off
the power supply, then restore power supply
again.
B - It is better not to let the horizontal adjustment
louver tilt downward for a long time at
COOLING or DRY mode to prevent
condensed water from dripping.
Operation mode Direction of airflow
COOLING, DRY horizontal
*HEATING, FAN ONLY downward
control rod of vertical
adjustment louvers

12
MODE AND FUNCTION DESCRIPTIONS
6th SENSE MODE
Press the button, the unit enters 6th sense
mode directly regardless of the unit is on or off.
In this mode, temperature and fan speed are
automatically set based on the actual room
temperature.
Operation mode and temperature are
determined by indoor temperature.
Heat pump models
Button is ineffective in Jet mode.
Note: Temperature, airflow and direction are
controlled automatically in 6th sense mode.
However, a decrease or rise of up to 2°C can be
set with the remote control if you still feel
uncomfortable.
What you can do in 6th sense mode
Indoor
temperature Operation mode Target temperature
21°C or below HEATING 22°C
21°C-23°C FAN ONLY
23°C-26°C DRY
Room
temperature
decrease 2°C
after operating
for 3 minutes
Over 26°C COOLING 26°C
Your feeling button adjustment procedure
Uncomfortable because of unsuitable
air flow volume. Indoor fan speed alternates among High, Medium and Low each time this button is pressed.
Uncomfortable because of unsuitable
flow direction. Press it once, horizontal adjustment louver swings to change horizontal airflow direction. Press it
again, swings stops. For vertical airflow direction
please refer to the chapter "Airflow direction
control".

13
Clock function
You can adjust the real time by pressing TIMER
ON/CLOCK button. Press this button and hold for
over 3 seconds to activate the clock setting, clock
digit will flash, then using and buttons to
get the correct time, press this button again, the
real time is set.
SLEEP mode
SLEEP mode can be set in COOLING,
HEATING or DRY operation mode.
This function gives you a more comfortable
environment with low noise level for sleep.
In SLEEP mode,
• The appliance will turn off automatically after
operating for 8 hours.
• Fan speed is automatically set at low speed.
• Set temperature will rise by max 1°C if the
appliance operates in cooling mode for 1 hour.
• Set temperature will decrease by 3°C at most if
the appliance operates in heating mode for 3
hours.
Note: In cooling mode, if room temperature is
26°C or above, set temperature will not change.
Heating is NOT available for cooling only air
conditioner.
Once sleep mode is set, "sleep" indicator on front
panel display will light up and "Running" indicator
will flash for 10 times, then the whole display will
light off.
JET mode
•JET mode is used to start or stop fast cooling or
Heating.
Fast cooling operates at high fan speed, and set
temperature automatically to 18°C.
Fast heating operates at auto fan speed,changing
set temperature automatically to 32 °C.
•InJET mode, you can set airflow direction or
timer. If you want to quit from JET mode, press
any - JET, MODE, FAN, ON/OFF or
TEMPERATURE SETTING button, the display
will return to the original mode.
Note:
• SLEEP and 6th Sense buttons are not available in
JET mode.
• The appliance will continue working in JET mode
if you don't quit from it by pressing any of the
buttons mentioned.

14
Timer function
It is convenient to set the timer on by pressing the
TIMER ON/CLOCK button to achieve a
comfortable room temperature at the time you get
home.
You can also set timer off by pressing the TIMER
OFF button to enjoy a good sleep at night.
How to set TIMER ON
TIMER ON/CLOCK button can be used to set the
timer programming as wished in order to switch on
the appliance at your desired time.
i) Press TIMER ON/CLOCK button, when "ON
12:00" flashes on the LCD, then you can press the
or buttons to select your desired time for
appliance on.
Press the or button once to increase or
decrease the time setting by 1 minute.
Press the or button for 5 seconds to
increase or decrease the time setting by 10
minutes.
Press the or button for a longer time to
increase or decrease the time by 1 hour.
Note: If you don't see the time in 10 seconds after
you press TIMER ON/CLOCK button, the remote
control will exit the TIMER ON mode
automatically.
ii)
When your desired time displayed on LCD, press
the TIMER ON/CLOCK button and confirm it.
A "beep" can be heard.
"ON" stops flashing.
The TIMER indicator on the indoor unit lights up.
iii) After the time set displayed for 5 seconds the
clock will be displayed on the LCD of the remote
control instead of set timer.
How to cancel TIMER ON
Press the TIMER ON/CLOCK button again, a
"beep" can be heard and the indicator disappears,
the TIMER ON mode has been canceled.
Note: It is similar to set the TIMER OFF, you can
make the appliance switch off automatically at your
desired time.
OON
Increase
Decrease

15
Around U function
When you press this button, will display,
remote control transmits the actual room
temperature around it to the indoor unit, and the
appliance will operate according to this
temperature to let you feel more comfortable.
Please keep the remote control in a location where
it can transmit the signal to the indoor unit
properly.
Press once to set and press again to cancel.
DIM function
Press this button to turn on or turn off display light
on indoor unit control panel.
Press once to turn off the indoor unit display light,
press again or press any other buttons to turn it
on.
If you press the other buttons when the indoor unit
display light is off, press once to turn on the light,
press the second time for activating the function.
POWER SAVE function
POWER SAVE mode can be available in
COOLING, HEATING, DRY and FAN ONLY
operation mode.
When pressing this button, will display on
remote control.
POWER SAVE function under COOLING,
HEATING and DRY mode, the appliance will set
the temperature at 25°C with low fan speed.
POWER SAVE function under FAN ONLY mode:
the appliance will set at low fan speed.
Change mode or press the power save button
again to cancel this function.
Note: Fan speed and temperature can not be
adjusted under this mode.

16
EMERGENCY OPERATION
Under emergency situation or when remote control is
missing, you can control the unit by pressing the on/off
swith located on the indoor unit.
• Turn on the appliance: when the unit is off, press
this button, it will start up and operate in 6th
SENSE mode.
• Turn off the appliance: when the unit is on, press
this button, the unit will stop working.
Note: Do not press this button for a long time as
it will cause malfunction.
Auto-Restart Function
If you want to set auto-restart, switch on the power supply, press the ON/OFF button on the indoor unit
and hold for over 5 seconds, auto-restart is set with buzz sound.
If the auto-restart has been set, press the ON/OFF button on the indoor unit and hold for over 5 seconds,
auto-restart function will be cancelled with a buzz sound and air conditioner is on standby mode.
on/off switch
PROTECTION
Operating condition
The protective device maybe trip and stop the
appliance in the cases listed below.
If the air conditioner runs in COOLING or DRY
mode with door or window opened for a long
time when relative humidity is above 80%, dew
may drip down from the outlet.
Features of protection device
Wait at least 3 minutes before restarting the unit
after operation stops or changing mode during
operation. After connecting to power supply and
turning on the appliance immediately, a delay of 20
seconds may occur before it starts to operate. If all
operation has stopped, press ON/OFF button
again to restart. Timer should be set again if it has
been cancelled.
Features of COOLING mode
Anti-freezing
When the temperature of the indoor heat
exchanger drops to 0° or below, compressor will
stop working to protect the appliance.
Features of HEATING mode
Preheating
In order to prevent cool air blowing, 2-5 minutes
are necessary to preheat the indoor unit at
HEATING operation start. The indoor fan will not
work during preheating.
Defrosting
In HEATING operation the appliance will defrost
(de-ice) automatically to raise efficiency. This
procedure usually lasts 6-10 minutes. During
defrosting, fan stops running and running indicator
flashes.
After defrosting is completeed, it returns to
HEATING mode automatically.
Heating
Outdoor air temperature is over 24°C
Outdoor air temperature is below -7°C
Room temperature is over 27°C
Cooling Outdoor air temperature is over 43°C
Room temperature is below 21°C
Dehumidifying Room temperature is below 18°C

MAINTENANCE
Clean front panel of Indoor Unit
1. Disconnect from the power supply
Turn off the appliance first before disconnecting
from power supply.
2. Remove the front panel
Open the front panel as shown by the arrow
(Fig. A).
Pull the slots at the side of the front panel with
force to take out the front panel (Fig. B).
3. Clean the front panel
Wipe it with a soft and dry cloth. Use lukewarm
water (below 40°C) to clean if the appliance is
very dirty. After cleaning let it dry.
4. Refit and close the front panel.
Refit and close the front panel by pushing it
downward.
Note:
• Do not use substances such as gasoline or
polishing powder to clean the appliance.
• Do not sprinkle water onto the indoor unit
Dangerous! Electric shock!
Clean Air filter
It is necessary to clean the air filter after using it
for about 200 hours.Clean the air filter every two
weeks if the air conditioner operates in an
extremely dusty environment.
1. Disconnect from the power supply
Turn off the appliance first before disconnecting
from power supply.
2. Take out air filter (Fig. C).
1. Open the front panel.
2. Press the handle of the filter gently.
3. Slide out the filter.
3. Cleaning the air filter (Fig. D).
If the filter is very dirty, clean it with a solution
of lukewarm water and neutral detergent.
After cleaning let it dry.
4. Refit the filter, press the filter reset button
(Fig. E) at right side by using a cylinder pin and
close the front panel.
Note:
• To avoid injury, do not touch the fins of
indoor unit with your fingers after
removing the filter.
• Do not attempt to clean the inside of the
air conditioner by yourself.
• Do not clean the filter in washing machine.
Fig. A
Fig. B
Fig. C
Fig. D
17
Fig. E
Filter Reset button

18
TROUBLESHOOTING
Trouble Analysis
Does not run
• Is the protection device or fuse blown?
• Please wait for 3 minutes and start again, protection device may be preventing
unit to work.
• Are the remote control batteries low?
• Is the plug not properly plugged?
No cooling or
heating air
• Is the air filter dirty?
• Are the intakes and outlets of the air conditioner blocked?
• Is the temperature set properly?
• Are doors or windows open?
Ineffective control • Has there been a strong interference (from excessive static electricity discharge, power supply voltage abnormality)? Note that operation will be abnormal, in this
case unplug from the power supply and re-plug after 2-3 seconds.
Does not operate
immediately • 3 minute delay will occur when changing mode during operation.
Peculiar smell • This smell may come from another source such as furniture, cigarette etc, which
is sucked in the unit and blown out with the air.
A sound of running
water • Normal behaviour caused by the flow of refrigerant in the air conditioner. • Defrosting sound in heating mode.
Cracking sound • The sound may be generated by the expansion or contraction of the front panel
due to temperature changes.
Mist sprays from
the outlet
• Mist is present in the room with low temperature? Normal behaviour due to
cool air discharged from indoor unit during COOLING or DRY operation
mode.
Running indicator
flashes but indoor
fan stops.
• The unit is shifting from heating mode to defrost. The indicator will light off and
return to heating mode.
Operation problems are often due to minor causes, please check and refer to the
following chart before contacting the service. This may save time and unnecessary
expenses.
Note: If the problems still have, turn off the appliance and disconnect from power supply,
then contact the nearest Whirlpool Authorized Service Center. Do not attempt to move,
repair, disassemble, or modify the appliance by yourself.

INSTALLATION INSTRUCTIONS
Installation diagram
NOTE: The figure above is only a simple presentation of the unit, it may not match the external
appearance of the product you purchased. Installation must be performed in accordance with the national
wiring standards by authorized service people only.
Distance from wall
should be over 50mm
Distance from ceiling
should be over 200mm
Distance from floor
should be over 2500mm
Distance from the wall
should be over 50mm
Air intake distance from
the wall should be over
250mm
Air intake distance from
the wall should be over
250mm
Air outlet distance from the wall
should be over 500mm
Over 250mm
19
Outdoor unit
Indoor unit

20
INSTALLATION SERVICE
Before installation
1. Please read this manual carefully
before installation.
2. The appliance must be installed
according to national wiring rules
and according to this manual by
qualified technicians.
3. Any change of installation
position must be handled by
professionals;
4. Check the product to verify that
it has not been damaged before
installation.
5. Mount with the lowest moving
parts of indoor unit at least 2.5m
above floor or grade Level.
6. After installing, the consumer
must operate the appliance
correctly according to this
manual, keep a suitable storage
for maintenance and move of it
in the future.
SAFETY PRECAUTION
1. The power supply must be of
rated voltage with special
circuitry for the appliance. The
normal operating range of voltage
is 90%~110% of rated voltage.
The diameter of the power cord
must comply with requirements.
2. The user power supply shall have
a reliable grounding terminal. It is
prohibited to connect the
grounding wire to the following
items:
1) Water Supply Pipe
2) Gas Pipe
3) Sewage Pipe
4) Other positions that are
considered unsafe.
3. Ensure safe grounding and a
grounding wire connected with
the special grounding system of
the building, installed by
professionals. The appliance must
be fitted with electrical leakage
protection switch and an auxiliary
circuit breaker with sufficient
capacity. The circuit breaker
must also have a magnetic and a
thermal tripping function to
ensure protection in case of
short-circuit and overload.
Typ e Model Required Capacity
of air break switch
Split On/off 7/9K 10A
12/18K 16A