Whirlpool CGM2745FQ User manual

www.whirlpoolcommerciallaundry.com
W10867001A
W10867002A – SP
TABLE OF CONTENTS
DRYER SAFETY ....................................................................... 2
TOOLS & PARTS ..................................................................... 5
DIMENSIONS/CLEARANCES ................................................ 6
GAS DRYER INSTALLATION REQUIREMENTS .................... 7
ELECTRIC DRYER INSTALLATION REQUIREMENTS ....... 10
DRYER VENTING REQUIREMENTS .................................... 13
GAS SUPPLY CONNECTION ................................................ 15
INSTALLING LEVELING LEGS, COIN SLIDE, AND
COIN BOX............................................................................... 17
ELECTRIC DRYER ELECTRICAL CONNECTIONS ............. 18
LEVELING .............................................................................. 23
COMPLETE INSTALLATION ................................................. 24
REVERSING DRYER DOOR SWING .................................... 25
CHANGING TO A 30- OR 60-MINUTE TIMING CAM .......... 26
MAINTENANCE INSTRUCTIONS ......................................... 27
IF YOU NEED ASSISTANCE ................................................. 27
WARRANTY............................................................................ 28
TABLE DES MATIÈRES
SÉCURITÉ DE LA SÉCHEUSE ........................................... 29
OUTILS ET PIÈCES ............................................................. 32
DIMENSIONS/DISTANCES DE DÉGAGEMENT ................ 33
EXIGENCES D’INSTALLATION POUR LA
SÉCHEUSE À GAZ............................................................... 34
EXIGENCES D’INSTALLATION POUR
LA SÉCHEUSE ÉLECTRIQUE ........................................... 37
EXIGENCES CONCERNANT L’ÉVACUATION
DE LA SÉCHEUSE .............................................................. 39
RACCORDEMENT À LA CANALISATION DE GAZ ........... 41
INSTALLATION DES PIEDS DE NIVELLEMENT,
DE LA GLISSIÈRE À MONNAIE ET DE LA
CAISSE À MONNAIE ........................................................... 43
NIVELLEMENT ..................................................................... 44
ACHEVER L’INSTALLATION ................................................ 45
INVERSION DU SENS D’OUVERTURE DE LA PORTE ...... 46
INSTALLATION D’UNE CAME DE MINUTAGE
DE 30 OU 60 MINUTES ........................................................ 47
INSTRUCTIONS D’ENTRETIEN .......................................... 48
SI VOUS AVEZ BESOIN D’ASSISTANCE ............................ 48
GARANTIE............................................................................. 49
INSTALLATION INSTRUCTIONS
COMMERCIAL DRYER GAS OR ELECTRIC
INSTRUCTIONS D’INSTALLATION
SÉCHEUSE ÀUSAGE COMMERCIAL ÀGAZ OU ÉLECTRIQUE

2
DRYER SAFETY
QIt is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer
smells gas. This information should be obtained from your gas supplier.
QPost the following warning in a prominent location.

3
DRYER SAFETY
IMPORTANT: When discarding or storing your old clothes dryer, remove the door.

4
DRYER SAFETY
QClean dryer lint screen before or after each load.
QDo not use this dryer without the lint screen in place.
QDo not repair or replace any part of the dryer or attempt
any servicing unless specically recommended in this
Installation Instructions or in published user-repair
instructions that you understand and have the skills
to carry out.
QDo not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
QDo not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
QThe nal part of a tumble dryer cycle occurs without
heat (cool-down cycle) to ensure that the articles are left
at a temperature that ensures that the items will not be
damaged.
QWARNING: Never stop a tumble dryer before the end of
the drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated. (Avoids risk of
spontaneous combustion).
QKeep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
QThe interior of the dryer and dryer exhaust vent should be
cleaned periodically by qualied service personnel.
QSee “Electrical Requirements” section for grounding
instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of re, electric shock, or injury to persons when using the dryer, follow basic
precautions, including the following:
SAVE THESE INSTRUCTIONS
QRead all instructions before using the dryer.
QThis dryer is intended only for drying clothes and textiles
that have been washed in water. Do not use for any
other purpose.
QWARNING: If you smell gas, do not use the dryer or any
electrical equipment nearby. Warn other people to clear
the area. Contact the dryer owner immediately.
QDo not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to
a chemical reaction that could cause a load to catch re.
QDo not dry articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other ammable, or explosive
substances as they give off vapors that could ignite or
explode.
QDo not dry unwashed items in the dryer.
QDo not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
QBefore the dryer is removed from service or discarded,
remove the door to the dryer compartment.
QDo not reach into the dryer if the drum is moving.
QDo not open door while dryer is in operation. It will stop.
QDo not install or store the dryer where it will be exposed
to water and/or the weather.
QDo not tamper with controls.

5
Tools Needed:
8" (203 mm) 8" (203 mm) or 10" (254 mm) Flat-Blade Screwdriver Phillips Screwdriver
or 10" (254 mm) Adjustable Wrench
Pipe Wrench that opens to 1" (25 mm)
Torx®† T-20 Security 1" (25 mm) Hex-Head 5⁄16" (8 mm) Socket Wrench Pliers (that open to
Screwdriver or Bit Socket Wrench 19/16" [39 mm])
Level Utility Knife 1/4" (6 mm) Nut Driver 27" (686 mm)
Wood Block
Caulk Gun and Caulk Vent Clamps Pipe-Joint Compound Putty Knife
(for installing new exhaust vent) Suitable for Gas Type
Flashlight (optional) 1" (25 mm) Ruler or Measuring Tape
Open-End Wrenches
TOOLS & PARTS
†® TORX and T25 are registered trademarks of Acument Intellectual Properties, LLC.
Parts Supplied:
Foot Boots (4) Leveling Legs (4) Security Cone
(on some models) Service Door Lock Assembly
(on some models)
Coin Slide Decal Kit
(on some models)
6-Pin 30-Minute Timing Cam
(on some models)
3-Pin 60-Minute Timing Cam
(on some models)
5/16" Hex Head –
18 x 2½" Security Bolt
(on some models)
252525
25252525
2525252525
25 2525252525
25 25 2525252525
25 25 252525252525
$2.00
$1.75
$1.50
$1.25
$1.00
$0.75

6
DIMENSIONS/CLEARANCES
Side View Back View
Dimensions
Clearances
291/4"
(743 mm)
35"
(889 mm)
81/4"
(210 mm)
1"
(25 mm)
26"
(660 mm)
31/4"
(83 mm)
71/2"
(191 mm)
0"
(0 mm)
0"
(0 mm)
15"
(381 mm)
14" max
(356 mm)
0"
(0 mm)
11/2"
(38 mm)
51/2"
(140 mm)
10
3/4
"
(273 mm)
371/2"
(953 mm)
(gas models)
41"
(1042 mm)
131/2"
(343 mm)
Electric
Gas
27"
(686 mm)
31/4"
(83 mm)
36"
(914 mm)
(electric models)
4" dia
(102 mm)
131/2"
(343 mm)
Front View, Recessed Opening Side View, Recessed In Closet
0"
(0 mm)
14" max
(356 mm)
0"
(0 mm)
1"
(25 mm)
3"/3"
(76 mm)
3"/3"
(76 mm)
48"2/48"2
(310 cm2)
24"2/24"2
(155 cm2)
15"
(381 mm)
Closet Door to
Front of Dryer

7
Your dryer can be installed in a basement, laundry room, or
recessed area.
This dryer is not intended for installation in a mobile home.
Companion appliance location requirements should also be
considered.
IMPORTANT: Do not install or store the dryer where it will be
exposed to water and/or the weather. Proper installation is your
responsibility.
You will need:
QA grounded electrical outlet located within 6 ft. (1.8 m) of
where the power cord is attached to the back of the dryer.
See “Electrical Requirements.”
QA level oor with a maximum slope of 1" (25 mm) under
entire dryer. Installing the dryer on soft oor surfaces,
such as carpets or surfaces with foam backing, is not
recommended.
Gas dryer installation clearances
QThe location must be large enough to allow the dryer door to
be fully opened.
QAdditional spacing should be considered for ease of
installation and servicing. The door opens more than 180°.
QAdditional clearances might be required for wall, door, and
oor moldings.
QAdditional spacing of 1" (25 mm) on all sides of the dryer is
recommended to reduce noise transfer.
When installing a gas dryer:
IMPORTANT: Observe all governing codes and ordinances.
QCheck code requirements: Some codes limit or do not
permit installation of clothes dryers in garages, closets, or
sleeping quarters. Contact your local building inspector.
QMake sure that lower edges of the cabinet, plus the back
and bottom sides of the dryer, are free of obstructions to
permit adequate clearance of air openings for combustion
air. See “Recessed Area and Closet Installation Instructions”
below for minimum spacing requirements.
Location Requirements
GAS DRYER INSTALLATION REQUIREMENTS
Recessed Area and Closet Installation Instructions
This dryer may be installed in a recessed area or closet. For
recessed area and closet installations, minimum clearances
can be found on the warning label on the rear of the dryer
or in “Dimensions/Clearances.”
The installation spacing is in inches and is the minimum
allowable. Additional spacing should be considered for ease
of installation, servicing, and compliance with local codes and
ordinances.
If closet door is installed, the minimum unobstructed air
opening in the top and bottom is required. The unobstructed
opening needs to be 1 square inch per 1,000 Btu (252 kcal)
of gas burner output. Output on North American gas dryers
is typically 22,000 Btu; however, Canadian dryers may have
lower output. Louvered doors with equivalent air openings are
acceptable.
The dryer must be exhausted outdoors.
No other fuel-burning appliance may be installed in the same
closet as the dryer.
24 in.2
(155 cm
2)
48 in.2
(310 cm2)3"
(76 mm)
3"
(76 mm)
Closet
door
Front
View
Closet
Door
Front
View

8
Gas Dryer Grounding
IMPORTANT: The dryer must be electrically grounded in
accordance with local codes and ordinances or, in the absence
of local codes, with the National Electrical Code, ANSI/NFPA
70, latest edition, or Canadian Electrical Code, CSA C22.1.
If codes permit and a separate ground wire is used, it is
recommended that a qualied electrical installer determine
that the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park, Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
QDo not ground to a gas pipe.
QDo not have a fuse in the neutral or ground circuit.
QA 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical
circuit is required. A time-delay fuse or circuit breaker is also
recommended. It is recommended that a separate circuit
serving only this dryer be provided.
QThis dryer is equipped with a power supply cord having a
3-prong grounding plug.
QTo minimize the possibility of shock, the cord must be
plugged into a mating, 3 prong, grounding-type outlet,
grounded in accordance with local codes and ordinances.
If a mating outlet is not available, it is the personal
responsibility and obligation of the customer to have the
properly grounded outlet installed by a qualied electrician.
QIf codes permit and a separate ground wire is used, it is
recommended that a qualied electrician determine that the
ground path is adequate.
QCheck with a qualied electrician if you are not sure the
dryer is properly grounded.
GAS DRYER INSTALLATION REQUIREMENTS
Electrical Requirements
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
■For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualied electrician or service representative
or personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug provided with
the dryer: if it will not t the outlet, have a proper outlet
installed by a qualied electrician.

9
IMPORTANT: Observe all governing codes and ordinances.
This installation must conform with all local codes and
ordinances. In the absence of local codes, installation must
conform with American National Standard, National Fuel Gas
Code ANSI Z223.1/NFPA 54 or CAN/CSA B149.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park, Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
The design of this dryer has been certied by CSA International
for use at altitudes up to 10,000 feet (3048 m) above sea level
at the B.T.U. rating indicated on the model/serial plate. Burner
input adjustments are not required when the dryer is operated
up to this elevation.
When installed above 10,000 feet (3048 m), a four percent
(4%) reduction of the burner B.T.U. rating shown on the model/
serial plate is required for each 1,000 foot (305 m) increase in
elevation. For assistance when converting to other gas types
and/or installing above 10,000 feet (3048 m) elevation, contact
your local service company.
Gas Supply
GAS DRYER INSTALLATION REQUIREMENTS

10
Your dryer can be installed in a basement, laundry room, or
recessed area.
This dryer is not intended for installation in a mobile home.
Companion appliance location requirements should also be
considered.
IMPORTANT: Do not install or store the dryer where it will be
exposed to water and/or the weather. Proper installation is your
responsibility.
You will need:
QA grounded electrical outlet located within 6 ft. (1.8 m) of
where the power cord is attached to the back of the dryer.
See “Electrical Requirements.”
QA level oor with a maximum slope of 1" (25 mm) under
entire dryer. Installing the dryer on soft oor surfaces,
such as carpets or surfaces with foam backing, is not
recommended.
Electric dryer installation clearances
QThe location must be large enough to allow the dryer door
to be fully opened.
QAdditional spacing should be considered for ease of
installation and servicing. The door opens more than 180°.
QAdditional clearances might be required for wall, door, and
oor moldings.
QAdditional spacing of 1" (25 mm) on all sides of the dryer is
recommended to reduce noise transfer.
Recessed Area and Closet Installation Instructions
This dryer may be installed in a recessed area or closet. For
recessed area and closet installations, minimum clearances
can be found on the warning label on the rear of the dryer
or in “Dimensions/Clearances.”
The installation spacing is in inches and is the minimum
allowable. Additional spacing should be considered for ease
of installation, servicing, and compliance with local codes and
ordinances.
If closet door is installed, the minimum unobstructed air
opening in the top and bottom is required. Louvered doors
with equivalent air openings are acceptable.
Location Requirements
The dryer must be exhausted outdoors.
24 in.2
(155 cm
2)
48 in.2
(310 cm2)3"
(76 mm)
3"
(76 mm
)
Closet
door
Front
View
ELECTRIC DRYER INSTALLATION REQUIREMENTS
Closet
Door
Front
View
Electrical Requirements – U.S.A. only
It is your responsibility:
QTo contact a qualied electrical installer.
QTo be sure that the electrical connection is adequate and in
conformance with the National Electrical Code, ANSI/NFPA
70-latest edition and all local codes and ordinances.
QThe National Electrical Code requires a 4-wire power supply
connection for homes built after 1996, dryer circuits involved
in remodeling after 1996, and all mobile home installations.
QA copy of the above code standards can be obtained from:
National Fire Protection Association, One Batterymarch
Park, Quincy, MA 02269.
QTo supply the required 3 or 4 wire, single phase, 120/240
volt, 60 Hz., AC only electrical supply (or 3 or 4 wire,
120/208 volt electrical supply, if specied on the serial/
rating plate) on a separate 30-amp circuit, fused on both
sides of the line. A time delay fuse or circuit breaker is
recommended. Connect to an individual branch circuit.
Do not have a fuse in the neutral or grounding circuit.
QDo not use an extension cord.
QIf codes permit and a separate ground wire is used, it is
recommended that a qualied electrician determine that the
ground path is adequate.