Whirlpool LE5720XP User manual

5
AUTOMATIC
DRYER
Electric Model
LE5720XP
and
Gas Model
LG572lXP
rave Ovens. Trash Compactors. Room AN Condltloners. Oehumldlflers. Aulomatlc Washers, Clothes Dryers. freezers, Refngeralor-Freezer

Parts and features
CYCLE CONTROL KNOB
\ TEMPERATURE SELECTOR
RMATION CENTER
START BUTTON
LOADING DOOR
L
Remove the Con-
sumer Buy Guide la-
bel before using
your dryer. It will be
easier to remove.
Wipe out the
dryer drum with a
damp cloth to re-
move dust from stor-
ing or shipping.
Copy your Model and Serial Numbers here
When you need service or call with a
question, have this information ready:
Complete Model Number
1. Complete Model and Serial Numbers
(from-the plate located as shown).
2. Purchase date from sales slip.
Complete Serlol Number
Copy this information in these spaces.
Keep this book, your warranty, sales slip
Purchase Date
and “Dryer Guide” in the Laundry Infor-
mation Center on the back of the dryer
Serwce Company and
console. Telephone Number
There is no warranty registration to return. Proof-of-purchase is oil
that is required for in-warranty service.
Contents
Paw
PARTS AND FEATURES . . . . -2
YOUR RESPONSIBILITIES.
SAFETY FIRST. . . . . . . . i
SELECTING A CYCLE AND
STARTING YOUR DRYER. . . . . 4
Dryer Cycles and Settings
Coal Down Times . :
DRYING TIPS. . . . . . . 7
FLUFFAIR Setting . . . .
TUMBLE PRESS@Setting . :
Drying Times. . . . . 8
Mixed Loads . . , . . . . . B
2 01985 Whirlpool Corporation
Lint Signal . 8
LINT SCREEN . . . 9
LINT REMOVAL . . . . . 9
CARING FOR YOUR DRYER. . 10
Vacation Care. . . . . . . 10
IF YOU NEED SERVICE OR
ASSISTANCE. . . . 11
I. Before Calling for
Assistance . . . . 11
2. If You Need Assistance . . 11
3,IfYouNeedService . . . . . . 11
4. If You Have a Problem . 11
Page

Your
Responsibilities
Read this “Use and Care Guide”
and your “Dryer Guide” carefully for
important use and safety information.
You are personally responsible for
making sure that your dryer..
l is installed by a qualified installer.
l is properly maintained.
l is installed in an area protected
from the weather.
l is properly installed and leveled in
a well ventilated room’ on a floor
that can support the weight.
l is located in an area where the tem-
perature is above 45°F (7.2”C).
l is connected to the right kind of out-
let, electric supply and grounding.*
l is properly connected to fuel and
exhaust systems:
l is used only for jobs normally ex-
pected of home clothes dryers.
l is not run where there may be explo-
sive fumes.
l is not used by children or anyone
unable to operate it properly,
‘See the”lnstallation Instructions” for
complete information.
/ l FOR YOUR SAFETY l
; IFYOUSMELLGAS: i
i 1. OPEN WINDOWS.
i 2. DON’T TOUCH ELECTRI-
t CAL SWITCHES.
i 3. EXTINGUISH ANY OPEN
i FLAME.
! 4. IMMEDIATELY CALL
YOUR GAS SUPPLIER.
t
i l FOR YOUR SAFETY l
DO NOT STORE OR USE
i GASOLINE OR OTHER
i FLAMMABLE VAPORS AND
! LIQUIDS IN THE VICINITY ’

SUGGESTED SUGGESTED
TYPE OF LOAD CYCLE TEMPERATURE
COlTONS - LINENS
EXTRA HEAVY - Bedspreads,
mattress pads, quilts. EX HEAVY
HEAVYWEIGHT FABRICS - Towels, PERMIT
jeans, corduroys, work clothes HEAVY PRESS
MEDIUMWEIGHT COTTONS - HEAVY
Sheets, pillowcases, cotton HIGH
underwear, diapers MEDIUM
LIGHTWEIGHT COTTONS - Batistes,
organdies, lingerie LIGHT
PERMANENT PRESS, SYNTHETICS PERMIT PRESS
AND BLENDS
HEAVYWEIGHT FABRICS -Work clothes, PERMIT
jackets, raincoats _. _, _. 40-50 MINS. PRESS
MEDIUMWEIGHT FABRICS - Shirts, play HEAVY
clothessheetsslacks 30-40 MINS. HIGH
LIGHTWEIGHT FABRICS - Lingerie,
blouses, dresses _. 20-30 MINS.
KNITS PERM’T PRESS
HEAVYWEIGHT - Cottons, rayons, PERM’T PRESS
blends,T-shirtsslacks, shirts _. 40-50 MINS. HEAVY HIGH
LIGHTWEIGHT - Synthetics (polyester, KNITS GENTLE
acrylic, etc.] and blends, lingerie, LOW
blouses, dresses 30-40 MINS.
LIGHTWEIGHT AND DELICATE FABRICS
Sheer Curtains (2 or 3 panels) 20-30 MINS.
PERM’T PRESS KNITS GENTLE
Gauze, lace,etc. _. _. 15-20 MINS. LOW
RUBBER, PLASTIC, HEAT-SENSITIVE PERMIT PRESS
FABRICS
FOAM RUBBER - Pillows, bras,
stuffed toys 20-30 MINS. FLUFF
PLASTIC - Shower curtains, AIR
tablecloths _. _. 20-30 MINS.
RUBBER-BACKED RUGS . . . 40-50 MINS.
OLEFIN. POLYPROPYLENE, SHEER NYLON 15-20 MINS.

Select a
1. CYCLE Set TEMPERATURE
2. SELECTOR
Turn the Control Knob either way to
point to the cycle and setting you
want. See page 6 for information on
the cycles.
Push the
3. START Button
The Cycle Control Knob should point to OFF when the dryer is not in use.
5
The dryer will start tumbling when
you push the START Button
To stop and restart
the dryer
To stop the dryer, open the door (or
turn the Control Knob to OFF).
To restart the dryer, close the door,
select cycle, if necessary, and push
START.
I

Operating instructions
Dryer cycles and settings
The PERMANENT PRESS Cycle helps
provide the special care that perma-
nent press and synthetic fabrics
need...a period of heated drying
followed by a 10 minute cool down.
The chart on page 4 suggests time
and temperature settings for different
kinds of loads.
The EX HEAVY, HEAVY, MEDIUM and
LIGHT cycles describe the loads
they are designed to dry The chart
on page 4 tells what is meant by
EX HEAVY, HEAVY, MEDIUM and LIGHT
loads
At each setting, the dryer will run
about long enough to dry the load
described by the setting. Example:
The HEAVY Cycle is designed to be
long enough to dry a load of heavy
fabrics [towels, jeans, corduroys, etc.]
when the Temperature Selector is set
on PERM’T PRESS/HEAVY HIGH.
I
C MORE TIME LESS TIME + I
If the load is not as dry as you want,
set the dial more to the lett the next
time you dry that kind of load.
If the load is dryer than you want.
set the dial more to the right the next
time you dry that kind of load.
6
Cool down times
In all cycles, the heat shuts off
before the dryer stops tumbling. This
codI down time helps:
l keep wrinkles from setting in.
l make handling the hot load items
easier.
I
COOL WWN COOL DOWN I
The PERMANENT PRESS Cycle has
10 minutes of cool down time at the
end of the cycle.
All other cycles have 5 minutes of
cool down time.

Drying tips
The dryer does not heat when the
Temperature Selector is set on FLUFF
AIR. This setting con be used to fluff
bedding, plastic tablecloths, foam
rubber pillows, stuffed toys, snea kers,
etc.
1. Set the Temperature Selector to
FLUFF AIR.
2. Set the Control Knob to the PERMA-
NENT PRESS Cycle and select the
number of minutes you want.
3. Push the START Button.
TUMBLEPRESS@ Setting
The TUMBLE PRESSsetting removes
wrinkles from dry clothing such as
items that may have been packed
rn a suitcase, closet, or items not
removed from the dryer.
1. Set Temperature Selector to PERMIT
PRESS/HEAVY HIGH.
2. Set Control Knob to TUMBLE PRESS.
3. Push START Button.
The load will tumble in heated air
for 5 minutes. The heat shuts off and
the dryer continues to tumble the

Drying times Mixed loads
Drying times will vary depending on:
. amount of moisture in the clothes, When drying a load with different
l type and weight of the fabric. kinds and weights of fabrics, use the
l size of the load. cycle suggested for the lightest
l room temperature around the fabrics. When the dryer stops, remove
dry items and reset the control.
dryer.
l temperature of the wash rinse
water.
l amount of lint in the lint screen.
l dryer temperature selection.
See page 6 in your”Dryer Guide”
for more information.
Lint signal
Clean lint screen before each load. If you
neglect to clean your lint screen, the signal will
sound. The (whistle tone] signal lets you know
the air flow is being restricted Restricted air flow
reduces drying efficiency.
Turn off the dryer and clean the lint screen as
shown on page 9.

Lint screen
Clean the lint screen before each load. A screen blocked by lint con
may be o FIRE HAZARD.
Open the lid and pull the lint screen
straight out. ROLL the lint off the screen
with your fingers.
DO NOT rinse or wash the screen.
Push the screen firmly bock into
place.
Lint removal
Lint con gather inside the dryer and create a fire hazard.This lint
should be removed every 2 to 3 years, or more often, depending on
dryer usage.
ELECTRIC DRYERS GAS DRYERS
Cleaning should be done only by a qualified person.
l Avoid electrfcal shock
hazard - unplug power
supply cord or turn off
electrical power.
l Avoid injury or damage - do not
put hands inside cabinet.
l Make sure dryer is cool.
1. Remove back panel (eleCtriC)
or lower access panel (gas).
2. Avoid damaging wires,
thermostats. funnel or igniter.
3. Remove lint from shaded area -
see art-with a soft brush or
vacuum cleaner.
4. Replace panel; reconnect and
re-level dryer.
9

Caring for your dryer
Remove sharp objects from clothing
before drying - pins, buckles, etc.
Close metal zippers.
Wipe off all spills with a damp, soft Sharp or heavy objects should
cloth. Spills allowed to remain may never be put on or in the dryer.
dull or damage the finish. Check pockets for bolts, nuts, etc
Never leave wet or damp laundry in
your dryer.
Non-colorfast items con stain the
drum. Wipe carefully after drying to
make sure there is no dye to be
transferred to items in the next load.
Vacation care
Some pretreatment products con
damage dials. console and finish. Do
not use these products on or near
your dryer.
Unplug power cord or For gas dryers, close
turn off electrical power. gas valve.
10
Clean lint screen.

If you need service or assistance, we suggest
you follow these four steps:
I. Before calling for assistance.. . 3. If you need service*. ..
Performance problems often re-
sult from little things you con find
and fix yourself without tools of any
kind.
DRYER DOES NOT RUN:
* Is power supply cord plugged in?
l Is door closed tightly?
l Did you push START Button?
l Are fuses blown or a circuit-breaker
tripped?
DRYER DOES NOT HEAT:
l The AIR setting is without heat.
l The lost minutes of heat settings ore
without heat.
l Is gas turned on? If not, turn Control
Knob to OFF-Turn on gas. Wait 5
minutes. Reset controls and start.
l An electric dryer uses a circuit
breaker or 2 fuses. If one fuse is
blown, the dryer may run, but not
heat.
DRYING TIME SEEMS LONG:
l Is the lint screen clean?
l See page 6 in your”Dryer Guide:’
2. If you need assistance*. ..
Call Whirlpool COOL-LINE@ serv-
ice assistance telephone number.
Dial free from:
Continental U.S. . [phone]
Michigan . . . . . . . [phone]
Alaska 6 Hawaii [phone]
and talk with one of ourtrained Con-
sultants. The Consultant con instruct
you in how to obtain satisfactory op-
eration from your appliance or, if
service is necessary, recommend a
qualified service company in your
area.
FSPISa reglstered trademark
0
of Whirlpool Corporatio‘n foe
quality park. Lad< for this
FSP
symbol of quality whenever
you need a replacement part
8 for your Whirlpool appliance
FSPreplacement pork
will fit right and wofk right, because they ore
made to the same exacting specifications
used to build every new Whirlpool appliance
Whirlpool has
a nationwide net-
1 work of franchised
ice technicians ore trained to fulfill
the product warranty and provide
after-warranty service,anywhere in
the United States. To locate TECH-
CARE service in your area, call our
COOL-LINE service assistance tele-
phone number (see Step 2) or look in
your telephone directory Yellow
Pages under:
.PPLI.*cES~HOUSE”clLD ELECTRlCIL.PPLI.NCES-
U.JORSERVICELREPAIR
OR
YIJOI REP.IR,MGI P.mTs
WHiRLP00~APPLIA.WCES W”,RLPOOL*PPuAYcEs
FRAN‘HISIDEC”CARESEWlCI lRlYt”lStDTECHCARESEWICi
\LRV,ChcOYPAV,b\‘ .SERV,(‘E~‘DYPAYlE!
112SEc-aCEco 1”ZSERVICEco
121Maple 9999999 111Y1DM 9s999
OR
WaSIIINGYACHl*ESDR”ERS
L,ROllLRS-SCRWCING
4. If you have a problem*...
Call our COOL-LINE service as-
sistance telephone number (see
Step 2) and talk with one of our Con-
sultants. or if you prefer, write to:
Mr. Robert F.Gunts, Vice President
Whirlpool Corporation
Administrative Center
2000 US-33 North
Benton Harbor, Ml 49022
*If you must call or write, please pro-
vide. model number, serial number,
dote of purchase. and a complete
description of the problem. This in-
formation is needed in order to bet-
ter respond to your request for
assistance.

Maklng your world a little easier.
Part No. 693694
01985 Whirlpool Corporation Printed in U.S.A.
natlc Washers. Clolhes Dryers. Freezers. Refrigerator-Freezers. Ice Makers. Dtshwashers. Bwlt-In Ovens and Surface Un~ls. Ranges. MIC