Whirlpool SCO-2433 User manual

ELECTRIC BUILT-IN
SINGLE & DOUBLE OVENS
MODELS (singles):
KESO- 14OSIl45SIl7OS/176S
SW-1243/2433/1273/2733
M0DEL.S (doubles):
KELI0-240SE/245SS/270SEl276SS
SC02243124431227312743
INSTALLATION
INSTRUCTIONS
INSTALLER: FIMAL CHECK LIST
IMP0 RTANT:
LEAVE THESE INSTRUCTIONS FOR LSE BY LOCAL ELECTRICAL INSPECTOR
PLACEMENT OF UNIT
0 1. Properly positioned-level, aligned and ;quare with cabinet opening.
0 2. Anchored securely to cabinet.
0 3. Installation debris removed.
ELECTRICAL
0 1. Oven properly grounded.
0 2. Separate 120/240 volt or 120/208 voh, 60 hertz, single phase branch of proper
ampacity and protected by a fuse or circuit breaker with approved rating.
0 3. All connections made in accordance with local and/or National Electrical Code.
OPERATIONAL
0 1. Oven racks installed and slide freely ir all positions.
0 2. Knobs securely in place and rotate fre ?ly without rubbing edges of control panel glass
holes.
0 3. All lights function properly.
0 4. Clock timer buzzer operates.
0 5. Doors properly adjusted, open and clcse smoothly.
0 6. Selector switch functions in all modes
0 7. Unless instructed to leave for owner, remove all tags, labels and internal packing
materials.
0 8. Oven has been wiped clean to remove fingermarks and other smudges.
THANK YOlI INSTALLER:
1. Complete Installat on Check List.
2. Leave all literature for customer.
3. Notify dealer that installation is completed.
FOR DETAILED INSTRUCTIONS. FOLLOW METHODS DESCRIBED IN THIS FOLDER.

IMPORTANT: Read Before Installing to Save Time, Work,
assure proper performance, and owner’s warranty protection.
INSTALLATION INSTRUCTIONS
CABINET CONTRUCTION
The first item for the installation of the oven will be to secure an appropriate cabinet or provide a properly
framed opening in the wall. Refer to Illustration and T;lbles below for the correct location and dimensions
to use. A solid bottom or runners, spaced on 19% cent’?rs are required in the opening to support the oven.
The front of the cabinet must be at right angles to the supports as well as level. If the oven is not
installed level, it will not cook properly.
- 24” -
to inslde of
cabinet back
------- A
31%”
to top of
oven support
I
- 24” -
to inside of
cabinet back
1
,;r - --
to top of
oven support
36”
-9 MIN-
%” to lower
cab. doors
61 ‘; MI N
2%” MIN
to upper
cab. doors
-A MIN-
.
*
t
- 8%”
! I
-
Junction Box
r -,
/
Furnished by
L’j _-
-7
Ins1
taller
-
-B MIN-
A
61” MIN
SINGLE OVENS
Model No. I A I B
Min. Cabinet Min. Cut Out
KESO-170
KESO-176
SCO-1273 27”
SCO-2733
24’/”
DOUBLE OVENS
Model No. A
Min. Cabinet
Width
KEDO-240
KEDO-245
SCO-2243 24”
SCO-2443
B
Min. Cut Out
Width
22%”
KEDO-270
KEDO-276
SCO-2273 27”
SCO-2743
24%”
-2-

ELECTRICAL
It is necessary to provide an appropriate junction box as shown on the previous page. The installation ot
this junction box and the wiring connecting it to the hollse wiring should be done by a qualified electrician.
All wiring must be done in accordance with the Natioral Electrical Code and/or any other applicable local
codes or ordinances.
The power supply to the junction box must be 120/240 volt or 120/208 volt, 60 hertz A.C. single phase, 3
wire. Do not connect the oven to a D.C. power suppllr as serious damage to the components will result.
Refer to TABLE 1 for fuse or circuit breaker size for the model being installed. Remember that the oven
must have a separate circuit. Do not operate other electr cal equipment on the same cirucit.
TABLE 1
Model No.
KESO-140/170
KESO-145/176
SCO- 1243/l 273
SCO-243312733
Maximum Wattage
3.8KW@;40V
Fuse or Breaker
Size Required
30 AMPS
KEDO-2401270
SCO-224312273
KEDO-245/276
SCO-244312743
6.0 KW@ 240 V
7.5 KW @ 240 V 40 AMPS
UNPACKING THE UNIT
The oven should be left on the carton base until it is ready to
put into the cabinet. It is also recommended that the patls over
the door(s) be left in place. These precautions will reduce the
possibility of damage to the front of the unit and the bot om of
the front frame.
Prior to installation, test the electrical service to assure that it
agrees with the specifications on the oven data plate.
Remove all cords, tape and wire used to hold various p3rts in
position during shipment. Remove oven racks from the inide of
the oven and put to one side while oven is being insta led in
cabinet. Take broiler pan and grid from packing on top If the
oven and keep with literature packet in a location when: they
will be retained by the owner.
To Remove Oven Rack8
Slide rack forward until bar on back of rack
touches first stop.
Lift front of rack until rear portion of rack
slides out between front two stops.
ELECTRICAL CONNECTION
WARNING: ELECTRICAL AND GROUNDING CONhECTlONS MUST COMPLY WITH THE APPLI-
CABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL
CODES.
WARNING: DISCONNECT ELECTRICAL POWER SU’PLY AND PLACE A TAG AT THE DISCON-
NECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT.
Connect the conduit from the oven to the junction box jnd properly connect to the power supply leads.
Bare to ground, black to L2, red to Ll, white to neutral or according to local code.)
GROUNDING -THE OVEN MUST BE GROUNDED.
Do not work on the oven wiring until the oven has been pc sitively grounded.
The oven frame is grounded through the bare groundiny wi-e. Connect it to ground in accordance with local
codes. Connect the white neutral to the service neutral win at the junction box.
-3-

INSTALLING THE UNIT IN CABINET
The doors should be removed to decrease the weight 0.’ the oven and provide a better hand hold on the
oven while lifting it into the cabinet,
A. To Remove Doors (See Fig. 1)
Use caution! Oven door is heavy.
1. Open door completely.
2. Depress finger tab in oven door hinge area. Push tab toward
oven. Lift tab away from door liner and slide toward top of
oven door.
3. Repeat step 2 for other side of door.
4. Close door until approximately 5 inches from Fully closed
position.
5. Slide door off the hinge arm assemblies.
6. Repeat steps 1 through 5 for other door on dcuble ovens.
Be sure that phenolic spacers at either side of oven are in place to
provide proper air flow between cabinet and oven.
When oven has been place into cabinet, the bottom trim strip is
placed on lower edge of front frame. This is done by lcosening the
three screws at the bottom of the front frame. Slide tl-e trim strip
under the screw heads until the strip meets the lower ccrners of the
front frame (See Fig. 2). Tighten screws to hold to front frame.
Secure oven to cabinet with # 8 screws provided. Do not over-tighten
screws. Edge of front frame should be parallel to cabinet. Disregard
any excess screws that are left after all screw holes in front frame
have been used. I
B. Replace Oven Racks in Oven Cavity.
C. Reinstall The Door(s) (See Fig. 1)
1. Slide door hinge arms until firmly seated.
2. Lower door to full open position.
3. Push finger tabs to back. Depress the tabs and slide forward.
4. Close and reopen door slowly to make sure it has been
replaced properly.
5. Repeat steps 1 through 4 for other door on double oven.
DOOR ADJUSTMEblT CHECK
A
NEWSPAPER STRIPS
TOP OF DOOR
NEWSPAPER !tTRIPS
SIDE OF I OOR
NEWSPAPER STRIPS
BOTTOM OF DOOR
w ADJUST IN i
ADJUST UP OR DOWN3
TO ALIGN DOOR
Place 2” x 18” strips of newspaper in lo-
cations indicated by illustration. Allow one
end of the paper to extend into the oven
cavity. Pull gently at each piece of paper. If
door is properly adjusted, each piece of
paper will offer firm resistance when pulled.
When door is out of adjustment. slide unit
out far enough to expose hinges on each
side. Loosen screws and move bottom of
door to a proper fit. After completing ad-
justment tighten all screws in hinges.
Specifications Subject to Change Without Notice
FORM 15922A
q 17-n 8J
PRINTED IN U.S.A.