Whispbar K432W User manual

K432W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 4 x 2
x 2
Revision No: 5D 1

Fitting Kit K432W
MAX kgs (lbs)
W/P WHD
Suzuki
Alto, 5dr Hatch 09-+ ZA 25 kgs (55 lbs) 25 kgs (55 lbs)
Alto, 5dr Hatch 09-+ ZA 25 kgs (55 lbs) 25 kgs (55 lbs)
Alto, 5dr Hatch 09-15 EU 25 kgs (55 lbs) 25 kgs (55 lbs)
Alto, 5dr Hatch 09-15 EU 25 kgs (55 lbs) 25 kgs (55 lbs)
Alto, 5dr Hatch Sep 09-+ NZ 25 kgs (55 lbs) 25 kgs (55 lbs)
Alto, 5dr Hatch Sep 09-+ NZ 25 kgs (55 lbs) 25 kgs (55 lbs)
Alto, 5dr Hatch Sep 09-+ AU 25 kgs (55 lbs) 25 kgs (55 lbs)
Alto, 5dr Hatch Sep 09-+ AU 25 kgs (55 lbs) 25 kgs (55 lbs)
2

Fitting Kit K432W
X
A B C 1 2 3
Alto, 5dr Hatch 09-+ (ZA) -200mm 450mm - - - -
-7 -7/8ths" 17 3/4ths" - - - -
Alto, 5dr Hatch 09-+ (ZA) -200mm 450mm - 769mm 709mm -
-7 -7/8ths" 17 3/4ths" - 30 1/4ths" 27 15/16ths" -
Alto, 5dr Hatch 09-15 (EU) -200mm 450mm - - - -
-7 -7/8ths" 17 3/4ths" - - - -
Alto, 5dr Hatch 09-15 (EU) -200mm 450mm - 769mm 709mm -
-7 -7/8ths" 17 3/4ths" - 30 1/4ths" 27 15/16ths" -
Alto, 5dr Hatch Sep 09-+ (NZ) -200mm 450mm - - - -
-7 -7/8ths" 17 3/4ths" - - - -
Alto, 5dr Hatch Sep 09-+ (NZ) -200mm 450mm - 769mm 709mm -
-7 -7/8ths" 17 3/4ths" - 30 1/4ths" 27 15/16ths" -
Alto, 5dr Hatch Sep 09-+ (AU) -200mm 450mm - - - -
-7 -7/8ths" 17 3/4ths" - - - -
Alto, 5dr Hatch Sep 09-+ (AU) -200mm 450mm - 769mm 709mm -
-7 -7/8ths" 17 3/4ths" - 30 1/4ths" 27 15/16ths" -
3

Fitting Kit EN
K432W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K432W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
5

Fitting Kit EN
K432W
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A = Clear
B = Grey
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 583A
B = 584B
6

Fitting Kit EN
K432W
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pad (supplied with crossbar) to
foot.
7

Fitting Kit EN
K432W
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
8

Fitting Kit EN
K432W
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
9

Fitting Kit EN
K432W
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10