Whispbar K506W Operation and installation manual

K506W
Fitting Kit
EN Fitting Instructions for Basic Carrier
CS Pokyny pro montáž základních nosičů
HU Felszerelési útmutató a
tetőcsomagtartóhoz
SK Pokyny pre montáž základných nosičov
x 2 x 2 x 2 x 2
x 4
Revision No: 5D 1

Fitting Kit K506W
MAX kgs (lbs)
W/P WHD
Audi
A5 Sportback, 5dr Coupe 09-16 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
A5 Sportback, 5dr Coupe 09-16 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
A5 Sportback, 5dr Coupe 09-16 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
A5 Sportback, 5dr Coupe 09-17 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
A5 Sportback, 5dr Coupe 10-17 CN 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K506W
X
A B C 1 2 3
A5 Sportback, 5dr Coupe 09-16 (NZ) -300mm 400mm - 895mm 870mm -
-11 -13/16ths" 15 3/4ths" - 35 1/4ths" 34 1/4ths" -
A5 Sportback, 5dr Coupe 09-16 (ZA) -300mm 400mm - 895mm 870mm -
-11 -13/16ths" 15 3/4ths" - 35 1/4ths" 34 1/4ths" -
A5 Sportback, 5dr Coupe 09-16 (EU) -300mm 400mm - 895mm 870mm -
-11 -13/16ths" 15 3/4ths" - 35 1/4ths" 34 1/4ths" -
A5 Sportback, 5dr Coupe 09-17 (AU) -300mm 400mm - 895mm 870mm -
-11 -13/16ths" 15 3/4ths" - 35 1/4ths" 34 1/4ths" -
A5 Sportback, 5dr Coupe 10-17 (CN) -300mm 400mm - 895mm 870mm -
-11 -13/16ths" 15 3/4ths" - 35 1/4ths" 34 1/4ths" -
3

Fitting Kit EN
K506W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K506W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K506W
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●Cut protective strip as shown.
6

Fitting Kit EN
K506W
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 688A
B = 689A
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
7

Fitting Kit EN
K506W
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-250
B = 11-04-251
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
8

Fitting Kit EN
K506W
●Clamps onto anchor points under rubber
door frame mouldings
●The rubber seal must be peeled back from
the vehicle body to allow the clamp to be
inserted between the vehicle body and the
rubber seal.
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the front of this manual for
information relating specifically to your
vehicle.
9

Fitting Kit EN
K506W
●Press adjusting screw to adjust the leg
positions on the crossbar.
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Tighten locking screw on both legs evenly.
10