Whispbar K820W User manual

K820W
Fitting Kit
EN Fitting Instructions for Basic Carrier
CZ Pokyny pro montáž základních nosičů
HU Felszerelési útmutató a
tetőcsomagtartóhoz
SK Pokyny pre montáž základných nosičov
x 4 x 2 x 2 x 4
x 4 x 1 x 4
Revision No: 1A 1

Fitting Kit K820W
MAX kgs (lbs)
W/P WHD
Renault
Clio, 5dr Hatch 05-12 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Clio, 5dr Hatch 05-12 CN 75 kgs (165 lbs) 75 kgs (165 lbs)
Clio, 5dr Hatch 07-10 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Clio, 5dr Hatch 07-12 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Clio, 5dr Hatch 07-14 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K820W
X
A B C 1 2 3
Clio, 5dr Hatch 05-12 (EU) -220mm 480mm - 790mm 745mm -
-8 -11/16ths" 18 7/8ths" - 31 1/8ths" 29 5/16ths" -
Clio, 5dr Hatch 05-12 (CN) -220mm 480mm - 790mm 745mm -
-8 -11/16ths" 18 7/8ths" - 31 1/8ths" 29 5/16ths" -
Clio, 5dr Hatch 07-10 (NZ) -220mm 480mm - 790mm 745mm -
-8 -11/16ths" 18 7/8ths" - 31 1/8ths" 29 5/16ths" -
Clio, 5dr Hatch 07-12 (AU) -220mm 480mm - 790mm 745mm -
-8 -11/16ths" 18 7/8ths" - 31 1/8ths" 29 5/16ths" -
Clio, 5dr Hatch 07-14 (ZA) -220mm 480mm - 790mm 745mm -
-8 -11/16ths" 18 7/8ths" - 31 1/8ths" 29 5/16ths" -
3

Fitting Kit EN
K820W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K820W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K820W
●NOTE: FRONT CROSSBAR ONLY
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
6

Fitting Kit EN
K820W
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-267
B = 11-04-268
7

Fitting Kit EN
K820W
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Place crossbar on vehicle.
8

Fitting Kit EN
K820W
●Clamps onto anchor points under rubber
door frame mouldings
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar.
●Set bars to length (revert to rear of these
instructions).
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Pull back rubber seal to expose fixed points
on vehicle body.
9

Fitting Kit EN
K820W
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Place clamp over the mounting hole
●Fit a fibre washer on each capscrew and
attach clamps to the vehicle body using the
capscrews.
●Use fixed-point rear mounting hole.
●Tighten locking screw on both legs evenly.
10