Whispbar K870W User manual

K870W
Fitting Kit
EN Fitting Instructions for Basic Carrier
ES Instrucciones de montaje para el sistema
de transporte
FInstructions de montage pour Basic Carrier
x 2 x 2 x 4 x 1
x 4 x 4 x 4 x 4
x 1
Revision No: 1A 1

Fitting Kit K870W
MAX kgs (lbs)
W/P WHD
Dodge
Grand Caravan , 5dr MPV Jan 11-+ US 68 kgs (149 lbs) 68 kgs (149 lbs)
Chrysler
Grand Voyager , 5dr MPV Jan 11-+ EU 68 kgs (149 lbs) 68 kgs (149 lbs)
Town and Country , 5dr MPV 11-+ US 68 kgs (149 lbs) 68 kgs (149 lbs)
Voyager , 5dr MPV Jan 11-+ CN 68 kgs (149 lbs) 68 kgs (149 lbs)
Volkswagen
Routan , 5dr MPV 11-14 US 68 kgs (149 lbs) 68 kgs (149 lbs)
Lancia
Voyager , 5dr MPV Jan 11-+ EU 68 kgs (149 lbs) 68 kgs (149 lbs)
2

Fitting Kit EN
K870W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●This kit fits type A, B, C and D.
●Use keys to remove covers.
3

Fitting Kit EN
K870W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Attaches to factory-fitted mounting points
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
4

Fitting Kit EN
K870W
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
5

Fitting Kit EN
K870W
Fitment
●Remove factory crossbars.
●Open or remove fixed-point covers.
●Locate vehicle's fixed points on inside of
rail.
●Select grubscrews and screw into the
vehicle's fixed points.
●Screw in 10mm, leaving 70mm showing.
●Do not over tighten.
6

Fitting Kit EN
K870W
●Thread the stabilizer brass nut onto the
grubscrew as shown.
●Use wrench provided to tighten brass nut.
●Repeat for all four positions.
●Refer to the underside of the pad for the
part number.
7

Fitting Kit EN
K870W
●Letters refer to the pad part numbers and
position.
●It is important to put the pads in the correct
position on the vehicle.
●Pad Part Number:
A = 233
B = 234
●Place pads over assembly as shown.
●Repeat for all four positions.
●Place crossbars on pads ensuring the pads
fit into the holes underneath the foot and
the grubscrew passes through the hole in
the foot.
8

Fitting Kit EN
K870W
●Place washer over clamp thread as shown.
●Ensure that tab is inserted into clamp
block.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all legs.
9

Fitting Kit EN
K870W
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10