WhisperGLIDE RockerGLIDE 700 Series User manual

Introduction & Important Information .......................... Page 2
Tools Required for Installation .................................. Page 3
Fastener Kit Identification ......................................... Page 3
RockerGLIDE Overall Dimensions .............................. Page 4
Assembly Instructions ........................................ Pages 5 to 7
Safety Instructions ....................................................... Page 8
Glider Use Instructions ................................................ Page 8
Maintenance ............................................................... Page 9
Cushion Care ............................................................ Page 10
Warranty .................................................................... Page 11
Contents
America’s Finest Therapeutic Swings!
by WhisperGLIDE Swing Co., LLC
OWNER’S MANUAL
Compact Two-Bench Glider
#700 SERIES MODEL & ACCESSORIES

Introduction & Important Information
Thank you for purchasing a Rocker GLIDE
aproduct of the Whisper GLIDE®Swing Company.
This manual covers its specifications, installation, use
and maintenance. Read this manual to learn how to
operate and care for your Rocker GLIDE. Failure to do
so could result in personal injury or equipment damage.
Do not throw away this manual.
Keep in a safe location for future reference.
All information, illustrations and specifications in this
manual are based on the latest information available at
the time of publication. The right is reserved to make
changes at any time without notice.
For information regarding Whisper GLIDE®Swings
and accessories, contact:
WhisperGLIDE®Swing Company, LLC
P.O. Box 188, Mosinee, WI 54455
s[email protected]
Tel. [phone]
FAX [phone]
www.whisperglide.com
Intended Use of the RockerGLIDE:
The Rocker GLIDE is designed with user safety in mind.
However, as with all mechanical equipment, there are
potential hazards which could result in injury to persons,
and/or structural damage to the equipment, if the glider
is improperly used or improperly supervised. The
Rocker GLIDE is designed for gentle back-and-forth
rocking and gliding motion. It is NOT intended for
rigorous aerobic or cardiovascular exercise. Use only
under adult or caregiver supervision.
The Rocker GLIDE is NOT public playground
equipment. This product is outside the scope of the
U.S. Consumer Product Safety Commission’s (CPSC)
definition of “public” playground equipment and
outside the scope of the American Society of Testing
and Materials (ASTM) Standard Consumer Safety
Performance specification for Playground Equipment for
Public Use. To reduce the potential for misuse of the
Rocker GLIDE as children’s play equipment, and the
potential for any related injuries, DO NOT place the
Rocker GLIDE in or near child play areas where
unsupervised access exists. If the glider is transferred
to another owner, notify Whisper GLIDE Swing Company
at 1-800-944-7737 and make the transferee aware
of the above information.
If the swing is transferred to another owner,
notify Whisper GLIDE at 1-800-944-7737 and make the
transferee aware of the above information.
PA G E T W O
PRIMARY COMPONENTS
The RockerGLIDE Materials
Floor Platform, Floor Support Frame, Seat Assembly Components, Seat Support Frame Aluminum
Seats, Arm Rests, Hand Rail Vinyl coated steel /
Aluminum
Fastener Nuts and Bolts Stainless steel
Table Fiberglass
Powder-coat paint finish Polyester
The RockerGLIDE Cushions Material Comment
WhisperGLIDE Series 600 Fabric - Vinyl-coated Meets flammability
EarthBright, Sea Breeze, Chesterfield, Autumn Fern, polyester rating CS191-53/CA
Elizabeth 117E
WhisperGLIDE Series 600 Fabric - Vinyl-coated olefin
Forest Green, Basketweave
Cushion fill Polyester fiber

Use Inside or Outside
P.O. Box 188, Mosinee, WI 54455
email: [email protected]
FAX: [phone] • www.whisperglide.com
©October 2019, WhisperGLIDE Swing Co.
For Additional Information
Check us out on our Website, or call us!
1-800-944-7737
Experience the Feeling!
AMERICAÕS FINEST THERAPEUTIC SWINGS
Tools Required for Installation
NOTE: USE ONLY HAND WRENCHES
DO NOT USE ELECTRIC WRENCHES, OR AIR-POWERED WRENCHES FOR SWING ASSEMBLY.
Use for Hand-Rails and Table:
One 1/2" wrench and one 9/16" wrench
or adjustable wrenches
Use for Platform base bolts:
One 9/16" wrench
or 9/16" socket wrench, or adjustable wrench
B5/16"-18 x 2-1/4" long
A3/8"-16 x 1-1/4" long
Fastener Kit Identification
The fastener kit contains labeled “subkits” for easy assembly of the swing.
Also, you can use the actual size fastener codes, identified below, for cross-reference.
A=Seats to Platform and
Floor Support Frame to Platform (20)
B=Handrail to Floor SupportFrame (2)
with AcornNut (2)
NOTE: In Step Four, you will find the the Acorn Nuts
and Bolts are packaged with the Table Handrails.
In Step Five, the Acorn Nuts and Lock Washers are
already fastened to the imbedded Bolts in the Table.
PAGE THREE

PAGE FOUR
RockerGLIDE Dimensions
Location Considerations – Must be placed on a level surface.
Allow adequate space to assist movement of a person
who uses a walker or wheelchair.
Allow an additional 2 feet on each end of the glider to give ample space when glider is in motion.
RockerGlide – Top View
RockerGlide – Side View
34-1/8"
Platform
Thickness:
1-1/2"
47-1/2"
56-1/4"

PAGE FIVE
Step One: Placement of the Platform
With the assistance of at least two people, place the platform base in the desired location.
Verify that that the placement meets all of the location considerations stated on the previous page.
•Place the floor support frame onto the platform so the holes align with the holes
in the middle of the platform.
•Have one person hold the floor support frame while the other person inserts and
finger tightens the four bolts (A), two on each side.
•Once all four bolts are fully seated into the platform, then tighten each bolt
using a 9/16" wrench or socket wrench.
Step Two: Mounting the Seats
Step Three: Mounting the Floor Support Frame
•Two people are required to lift the seat assembly
and place it onto the platform.
•Align the holes in the seat support base with the
holes at the end of the platform.
• Have one person hold the seat assembly in place while
the other person inserts and finger tightens the eight bolts (A).
•Once all eight bolts are fully seated into the platform,
then tighten each bolt using a 9/16" wrench or
socket wrench.
•Repeat the above steps for the opposite seat.