Whistler Pro-200W User manual

OWNER’S MANUAL
Pro-200W, Pro-400W
POWER INVERTERS
THE WHISTLER GROUP, INC.
CORPORATE HEADQUARTERS
3604 N.W. Frontage Rd.
Bentonville, AR 72712
TEL [phone] FX [phone]
www.whistlergroup.com
CUSTOMER RETURN CENTER
551 N. 13th St.
Rogers, AR 72756
Consumer Relations Tel [phone]
Email: [e-mail]
P/N 401514
© 2010 The Whistler Group, Inc.
pro200-400w.qxp 4/30/2010 9:06 AM Page 1

1
If you have questions concerning the
operation of this Whistler product
please call customer service:
1-800-531-0004
Hours:
Monday - Friday
8:00 am - 5:00 pm CT
or visit www.whistlergroup.com
Please keep the receipt in a safe place.
You may register your product online at
www.whistlergroup.com. If the unit is
returned without a dated proof of
purchase, an out of warranty service
charge applies. Note: Your warranty
period begins at the time of purchase.
The warranty is validated only by your
receipt.
Now is the time to record the serial
number of the unit in the space
provided in the warranty section of the
manual.
INTRODUCTION
Dear Whistler Owner,
For many of us, a vehicle is more than just transportation. It
can be a mobile office, communications or entertainment
center, or simply an expression of our personality. Whistler
products are designed to make the time you spend in your
vehicle more productive, more fulfilling, safer, or just simply
more fun. Our mission is to provide products that improve
your driving experience.
Whistler offers a complete line of DC to AC inverters
ranging from 100 Watts to 3000 Watts. These inverters offer
advanced technology, dependable operation and will
provide years of reliable service when used in accordance
with our operating instructions.
Your new Whistler power inverter allows you to run most AC
appliances right from your car, boat or RV. They’re great for
weekend use and life on the road. They’re also great for
power outages!
To fully acquaint yourself with the operation of this inverter,
we recommend reading this entire manual.
Sincerely,
THE WHISTLER GROUP, INC.
pro200-400w.qxp 4/30/2010 9:06 AM Page 3

A Word About WHISTLER Power Inverters.
WHISTLER inverters convert low voltage, direct current
(DC) to 110 volt alternating household current (AC). The
AC output is called “modified sine wave”. See “Technical
Operating Principles” section for more information.
Depending on the model and its rated capacity,
WHISTLER inverters draw power either from standard 12
volt automobile and marine batteries or from portable
high power 12 volt sources.
WHISTLER FEATURES
Topic Page
Features Summary......................................................................3
Important Information................................................................4
Inverter Basics .......................................................................5 - 7
• Getting Started
• Don’t Push It
Operation ............................................................................8 - 12
• Making the Connection
• Tips
• Recharging Equipment
• Changing the Fuse
• Power Source
Additional Safety Features...............................................13 - 14
• Auto Shut Down
• Thermal Cut Off
• Low Battery Protection
Care & Maintenance ................................................................15
Technical Operating Principles........................................16 - 17
Operation Summary.........................................................18 - 19
Troubleshooting ................................................................20 - 22
Specifications............................................................................23
Warranty Information........................................................24 - 26
TABLE OF CONTENTS
2
1. AC Output Sockets 6. High Speed Cooling Fan
2. On/Off Switch 7. Power Input Terminal Red = Positive
3. USB Power Port 8. Lighter Socket Power Cord
4. Power on LED 9. Battery Clamps
5. Power Input Terminal Black = Negative
3
pro200-400w.qxp 4/30/2010 9:07 AM Page 5

INVERTER BASICS
Getting Started
Power equipment and appliances which operate with motors
or tubes require an initial surge of power to get them up and
running. This power surge is referred to as the "starting load"
or "peak load." (By comparison, electrical devices such as
standard light bulbs do not require a large starting load).
Once the equipment or appliance has been powered up, it
settles down to a slower pace and requires far less electrical
power to operate. This lower power requirement is referred
to as the "continuous load."
In order to ensure that the capacity of your WHISTLER
inverter is sufficient to meet the required start up load, you
must first determine the power consumption of the
equipment or appliance you plan to operate.
Power consumption is rated either in wattage or amperes,
and information regarding the required "watts" or "amps"
generally is stamped or printed on most appliances and
equipment. If this information is not indicated on the
appliance or equipment, check the owner’s manual. Contact
the appliance or equipment manufacturer to determine
if the device you are using (TV’s, battery charger,
computer, medical equipment, etc.) is compatible with a
modified sine wave.
If the power consumption is rated in amps, multiply the
number of amps by 110 (AC voltage) to determine the
comparable wattage rating. Induction motors, as well as
some televisions, may require 2 to 6 times their wattage
rating for startup.
For further information on the fundamental operating
principles of WHISTLER inverters and related technical
data, see "Technical Operating Principles."
5
IMPORTANT INFORMATION
Important Information About Your New WHISTLER
Inverter.
This manual will provide you with directions for the safe
and efficient operation of your WHISTLER inverter. Read
the manual carefully before using your new WHISTLER
inverter and keep the manual on file for future reference.
Notes:
Your WHISTLER inverter is designed to operate from a 12
volt power source only. Never attempt to connect your
Whistler inverter to any other power source, including any
AC power source.
•The length of the supplied cables is matched for the
current needed by the inverter. Making this cable longer
will make the inverter less efficient and may cause the
cables to heat up.
•Do not attempt to lengthen the supplied power cables.
•110 volts can be lethal. Improper use of your WHISTLER
inverter may result in property damage, personal injury or
loss of life.
•Do not connect the inverter’s output to any other power
source.
•Not recommended for use with medical equipment.
Check with the appliance manufacturer for compatibility
with modified sine wave inverters. Some appliances may
not work well, not at all or be damaged. For more
information on compatibility issues, please visit our inverter
FAQ page.
4
pro200-400w.qxp 4/30/2010 9:07 AM Page 7

INVERTER BASICS
Don’t Push It.
Although your WHISTLER inverter has the capacity to
provide power output (excess current) equal to
approximately two times its rated wattage capacity for a
very brief period, it is designed to operate equipment and
appliances with start up load wattage ratings no higher than
its own maximum continuous wattage rating.
For example, the Pro-400W watt model has a maximum
continuous rating of 400 watts. Although this model has the
capacity to briefly provide more than its continuous power
(that is, excess current), it is designed to operate equipment
and appliances with start up load requirements of 400 watts
or less.
Consequently, if the start up load rating of your equipment
or appliance is slightly higher than the maximum continuous
rating of the inverter, the inverter will attempt to start loads
above the continuous rating for up to 10 seconds.
The inverter is designed to shut down automatically in the
event of a power overload. Testing appliances and
equipment with start up load ratings comparable to your
inverter wattage rating will not damage the inverter.
However, make sure the appliance you are testing is
compatible with modified sine wave inverters. See page 4
for more information.
7
INVERTER BASICS
6
If a piece of equipment or an appliance will not operate, first
confirm that the inverter has been properly connected to
the 12 volt power source (See "Making The Connection"). If
all connections have been properly made, turn the inverter
rocker switch ON (l), OFF (O) and ON (l) again in quick
succession. If this procedure is unsuccessful, it is likely that
the inverter does not have the required start up capacity to
operate the equipment or appliance in question.
Note:
•Most heat generating appliances require start up loads
in excess of 1000 watts and this inverter will not operate
such appliances as coffee makers, irons, hair dryers or
heaters.
•The inverter’s USB Port does not support data
communications.
•USB power is always on and independent of the
inverter’s on/off switch.
pro200-400w.qxp 4/30/2010 9:07 AM Page 9

OPERATION
Making the Connection.
This inverter is designed to connect to your 12 volt battery
using the lighter socket plug or by the supplied battery
cables (for appliances over 150 watts, 400 watt model only).
1. Make certain that the inverter rocker switch is in the
OFF (O) position.
2. Connect the lighter plug or hardwire cables to the
power input terminals at the rear of the inverter and
tighten the screws to make a secure connection.
Do not use tools to tighten these screws.
Steps 3 - 5 are used when any appliance requires
over 150 watts. Step 6 is for appliances under 150
watts.
3. Connect the cable from the (BLACK) Negative (-)
terminal on the inverter to the Negative (-) terminal on
the 12 volt power source. Make certain the
connection is secure.
4. Confirm that the cable you have just installed is
properly connected. Specifically, make certain that
the cable is connected to the Negative (-) terminals on
both the inverter and the 12 volt power source.
5. Connect the cable from the (RED) Positive (+) terminal
on the inverter to the Positive (+) terminal on the
power source.
9
OPERATION
6. Remove the lighter and insert the adapter plug firmly into
the cigarette lighter socket.* (Make certain both the
socket and adapter plugs are clean.)
Note:
•If the equipment or appliance you intend to operate
requires more than 150 watts of continuous power, this
inverter should be connected directly to the power
source using the Hard Wire Cables (400 watt model).
Failure to do so may result in serious damage to the
power cord or to the cigarette socket lighter wiring.
•Loose connections can result in a severe decrease in
voltage which may cause damage to the wires and
insulation.
•Failure to make proper connection between the inverter
and the power source will result in reverse polarity.
Reverse polarity will blow the internal fuse(s) and may
cause permanent damage to the inverter. Damage
caused by reverse polarity is not covered under the
WHISTLER warranty.
•Making the connection between the Positive terminals
may cause a spark as a result of current flowing to the
capacitors in the inverter. This is a normal occurrence.
Due to the potential for sparking, however, it is extremely
important that both the inverter and the 12 volt battery
be well removed from any possible source of flammable
fumes or gases.
Failure to heed this warning could result in fire or
explosion.
*Some vehicle lighter sockets may only supply 10 amps or approximately 100 watts. If so,
use the hardwire cables. Check vehicle’s owner’s manual for lighter socket fuse rating.
8
pro200-400w.qxp 4/30/2010 9:07 AM Page 11

•The use of an extension cord from the inverter to the
appliance or equipment being operated will decrease the
power being delievered to the load. For best operating
results, the extension cord should be no more than 50 feet
long.
•Check frequently to ensure that the input and output
connections are secure. Loose connections may damage
the inverter or the power source or may generate
excessive heat.
Important Information on Battery Chargers
Using your inverter with battery chargers for power tools,
flashlights, video cameras and laptop computers may cause
damage to the inverter or the charging unit. Check with the
appliance manufacturer for compatibility with modified sine wave
inverters if you’re unsure.
Although we advise against it, if you attempt to use a charging
unit, monitor the temperature of the charging unit for
approximately 10 minutes. If the charging unit becomes unusually
warm, disconnect it from the inverter immediately.
Don’t Blow A Fuse.
This inverter is equipped with an internal spade type fuse(s). With
reasonable care, it should not be necessary to replace the fuse(s)
in your inverter.
Most blown fuses are the result of reverse polarity or a short circuit
within the appliance or equipment being operated. If the fuse(s)
OPERATION
•Pro-400W watt model - If the supplied cables are too
short to allow for placement of the inverter in a
desired location, the inverter may be connected to
the power source using a #8 wire, up to 12’. Use #4
wire for longer lengths. The steps outlined for making
the connection and the related safety precautions
remain unchanged.
7. Turn the inverter rocker switch to the ON (I) position.
The LED Indicator Light should glow GREEN
confirming that there is power running to the inverter.
8. Turn the inverter rocker switch to the OFF (O) position.
(The GREEN LED Power Indicator light may “blink”
briefly and/or the internal audible alarm may make a
momentary “chirp”. This is normal).
9. Confirm that the equipment or appliance to be
operated is turned off. Plug the equipment or
appliance into one of the AC receptacles on the front
panel of the the inverter.
10. Turn the inverter to the ON (I) position. Turn on the
equipment or appliance.
11. Plug the USB powered device into the inverter’s USB
power port.
Note:
•As indicated in Step 7 above, the audible alarm may
make a momentary “chirp” when the inverter is
turned OFF (O). The same alarm may also sound
when the inverter is being connected to or
disconnected from the 12 volt power source.
11
OPERATION
10
pro200-400w.qxp 4/30/2010 9:07 AM Page 13

13
ADDITIONAL FEATURES
Automatic Shut Down & Related Safety Features.
Each inverter has an unique LED indicator warning light
system which operates in conjunction with the automatic
shut down feature. These indicator lights operate as follows:
GREEN LED: System ready.
RED LED: System overload/automatic shut down.
Your inverter will shut down automatically when any of the
following problems occur:
1. The power input from the battery drops below
10 volts.
2. The power input from the battery exceeds 15.5+/-0.5
volts.
3. The continuous draw of the appliance or equipment
being operated exceeds the design parameters of the
inverter.
The inverters are also equipped with the following additional
safety features:
1. Thermal Cut Off
Automatic shut down if internal temperature exceeds safe
design parameters.
OPERATION
12
does blow, turn off and disconnect the appliance or
equipment from the inverter immediately, repair the related
problem and replace the fuse(s). The internal fuses are
replaceable, however only electronically knowledgeable
people should attempt fuse replacement.
Note:
•Make certain to correct the source of the overload
which caused the blown fuse before turning your
inverter back ON (l).
The Power Source.
When the engine is off, most batteries will provide an ample
power supply to the inverter for one to two hours. The actual
length of time is a function of several variables including the
age and condition of the battery and the power demand
being placed on it by the equipment being operated with the
inverter.
If you are using the inverter while the engine is off, we
recommend you start the engine every hour and let it run for
at least 10 minutes to recharge the battery. We also
recommend that the device plugged into the inverter be
turned off before turning over the engine.
Although it is not necessary to disconnect the inverter when
turning over the engine, the inverter may momentarily cease
operation as the battery voltage decreases. When the inverter
is not supplying power, and is turned on, it draws very low
amperage from the battery (<0.70 A ).
pro200-400w.qxp 4/30/2010 9:07 AM Page 15

2. Low Battery Voltage Alarm/Shutdown Protection
a) When the input voltage from the 12 volt power source
drops below 10.5 volts, an audible tone will be heard.
This is the low battery voltage alarm.
b) The inverter will automatically shut down when the
input voltage drops below 10 volts. This protects the
battery from completely draining.
In the event of automatic shut down or continuous audible
alarm, turn the inverter rocker switch to the OFF (O) position
until the source of the related problem has been identified
and resolved.
Some Powerful Advice.
When driving with the inverter in operation, make certain that
neither the inverter nor the power cords will impede safe
operation of your vehicle. Keep the unit and all cords clear of
the steering wheel, gas, brake and clutch pedals and gear
shift.
14
ADDITIONAL FEATURES CARE AND MAINTENANCE
To maintain your inverter in proper working condition, note
the following important safety precautions:
•MOISTURE. Keep the inverter dry. Do not expose it
to moisture. Do not operate the inverter if you, the
inverter, the device being operated or any other
surfaces that may come in contact with any power
sources are wet. Water and many other liquids can
conduct electricity which may lead to serious injury or
death.
•HEAT. For peak efficiency, the ambient air
temperature should be between 50° and 80° F. Avoid
placing the inverter on or near heating vents,
radiators or other sources of heat. Do not place the
inverter in direct sunlight.
•VENTILATION. In order to disperse the heat
generated while the inverter is in operation, keep it
well ventilated. While in use, maintain several inches
of clearance around the top and sides of the inverter.
•FUMES & GASES. Avoid using the inverter near
flammable materials. Do not place the inverter in
areas such as battery compartments. Where fumes or
gases may accumulate.
In Review.
•Never attempt to operate your WHISTLER inverter
from any power source other than a 12 volt battery or
group of batteries that total 12 volts.
15
pro200-400w.qxp 4/30/2010 9:07 AM Page 17

17
16
OPERATING PRINCIPLES OPERATING PRINCIPLES
The majority of AC voltmeters measure RMS voltage and
assume that the measured waveform will be a pure sine
wave.
Consequently, these meters will not read the RMS modified
sine wave voltage correctly and, when measuring your
WHISTLER inverter output, the meters will read about 20 to
30 volts too low. To accurately measure the output
voltage of your inverter, use a true RMS reading
voltmeter such as a Fluke 87, Fluke 8060A, Beckman 4410,
Triplett 4200 or any multimeter identified as "True RMS."
For more information on inverters see our Inverter FAQ
page.
A true sine wave typical of home AC outlet.
For You Technical Types.
1. Basic Operating Principles:
WHISTLER inverters work in two stages. During the first
stage, the DC to DC converter increases the DC input voltage
from the power source (e.g. a 12 volt battery) to 145 volts DC.
In the second stage, the high voltage DC is converted to 110
volts (60 Hz AC) using advanced power MOSFET transistors
in a full bridge configuration. The result is excellent overload
capability and the capacity to operate difficult reactive loads.
The output waveform resulting from these conversions is a
"quasi-sine wave" or a "modified sine wave" as shown on
below.
This stepped waveform is similar to the power generated by
utilities and has a broad range of applications.
The modified sine wave produced by the Inverter
The modified sine wave produced by your Whistler inverter
has a root mean square (RMS) voltage of 110 volts.
pro200-400w.qxp 4/30/2010 9:07 AM Page 19

•When operating the inverter with the engine off, start the
engine every hour and let it run for at least 10 minutes to
recharge the battery.
•In the event of automatic shut down, turn the inverter OFF
(O) immediately. Do not restart the inverter until the
source of the problem has been identified and corrected.
• To avoid battery drain, always disconnect the inverter
when not in use.
•Do not expose the inverter to moisture.
• Avoid placing the inverter near sources of heat or in
direct sunlight.
•When in use, make certain that the inverter is properly
ventilated.
•Do not use the inverter near flammable materials,
fumes or gases.
•Always operate the inverter in accordance with the
instructions in this manual. Failure to do so may result
in property damage, personal injury or loss of life.
OPERATION SUMMARY
19
OPERATION SUMMARY
18
•This inverter is designed to be connected to the power
source with the supplied cables or with #8 wire up to 12’
Use #4 wire for longer length. When utilizing the
supplied cables do not attempt to modify or lengthen
them.
•Always make certain that the power cable terminal
connections Negative (-) to Negative (-) and Positive (+)
to Positive (+). Check these connections frequently to
ensure that they are secure.
•Make certain the rated power consumption of the
appliance or equipment you wish to operate is compatible
with the capacity of your inverter.
•If the rated power consumption of the equipment is in the
range of the maximum specified wattage of your
converter, test the inverter to ensure that it will operate
properly.
•This Inverter is not designed to operate heat generating
appliances such as coffee makers, irons, hair dryers,
toasters and heaters.
•Before attempting to use a battery charger see page 11.
•Before attempting to use medical equipment see page 4.
•Use only fuses which conform with the design
specifications outlined in this manual.
pro200-400w.qxp 4/30/2010 9:07 AM Page 21

2120
TROUBLESHOOTING TROUBLESHOOTING
PROBLEM: Low Battery Alarm On All The Time
Problem Solution
Input voltage below Keep input voltage above
10.5 volts. 10.5 volts to maintain
regulation.
Poor or weak battery Replace battery.
condition.
Inadequate power being Use lower gauge wire.
delivered to the inverter (400 watt model)
or excessive voltage drop.
Red LED On
Problem Solution
Equipment has a high Turn inverter power switch
start up surge. OFF (O) and then ON (l)
again until the inverter
powers your appliance.
Repeat as necessary
to get your appliance
"started".
Battery voltage below Recharge or replace
10 volts. battery.
Equipment being operated Use a higher capacity
draws too much power.inverter.
Inverter is too hot (thermal Allow inverter to cool.
shutdown mode). Check for adequate
ventilation. Reduce the
load on the inverter to
rated continuous power
output.
PROBLEM: TV Interference
Problem Solution
Electrical interference from Add a Ferrite data line filter
inverter.on to the TV power cord.
This filter is available at
electronic part stores.
.
PROBLEM: Low or No Output Voltage
Problem Solution
Using incorrect type of Use a true RMS reading
voltmeter to test output meter.
voltage. See "For You Technical
Types" Section of this
manual.
Please visit our Inverter FAQ page on our website
(www. whistlergroup .com), for more troubleshooting
information and FYI topics.
pro200-400w.qxp 4/30/2010 9:07 AM Page 23

SPECIFICATIONS
2322
TROUBLESHOOTING
PROBLEM: TV Does Not Work
Problem Solution
TV does not turn on. Try rocking the ON/OFF
switch of the inverter while
leaving the TV ON
(see page 7).
Contact TV manufacturer
for start-up surge and/or to
find out if TV is compatible
with a modified sine wave.
A larger inverter may be
required.
Pro-200W WATT INVERTER SPECIFICATIONS
Maximum Continuous Power .....................200 Watts
Maximum Surge Capability (Peak Power) 400 Watts *
No Load Current Draw......................................<0.6 A
Waveform....................................Modified Sine Wave
Operating Input Voltage Range.11– 15.5+/-0.5 Volts
AC Receptacle............ Two North American 3 Prong
Fuses .................... (1) 25 Amp (Spade Type-Internal)
USB..................................................5 Volt 500mA Max
Approximate Dimensions 5.15" L x 3.86" W x 1.81" H
Approximate Weight .......................................0.77 lbs
Pro-400W WATT INVERTER SPECIFICATIONS
Maximum Continuous Power .....................400 Watts
Maximum Surge Capability (Peak Power) 800 Watts *
No Load Current Draw......................................<0.7 A
Waveform....................................Modified Sine Wave
Operating Input Voltage Range11 – 15.5+/-0.5 Volts
AC Receptacle............ Two North American 3 Prong
Fuses ......................(2) 25 Amp (Spade Type-Internal)
USB..................................................5 Volt 500mA Max
Approximate Dimensions 5.15" L x 3.86" W x 1.81"H
Approximate Weight .........................................1.0 lbs
*
Under certain conditions your inverter may provide up to
2 times the continuous rating for a brief period.
pro200-400w.qxp 4/30/2010 9:07 AM Page 25

WARRANTY
IMPORTANT:Whistler will not assume responsibility for loss
or damage incurred in shipping. Therefore, please ship your
unit insured with return receipt requested.
2. Include the following clearly printed information:
• Your name and street address (for shipping via UPS),
a daytime telephone number, (No P.O. Box please.) and email
address (if applicable).
• A detailed description of the problem, i.e. Unit powers up but
no AC output.
• A copy of your dated store receipt or bill of sale.
3. Be certain your unit is returned with its serial number. For
reference, please write your unit’s serial number in the following
space: s/n __________________.
Units without serial numbers are not covered under warranty.
IMPORTANT: To validate that your unit is within the warranty
period, make sure you keep a copy of your dated store receipt.You
may register your warranty online at www.whistlergroup.com,
however, for warranty verification purposes, a copy of your dated
store receipt must accompany any unit sent in for warranty work.
25
WARRANTY
Consumer Warranty
This Whistler is warranted to the original purchaser for a
period of two years from the date of original purchase
against all defects in materials and workmanship. This
limited warranty is void if the unit is abused, modified,
installed improperly, had its housing removed, or has a
missing serial number.There are no express warranties
covering this product other than those set forth in this
warranty. All express or implied warranties for this product
are limited to two years. Whistler is not liable for damages
arising from the use, misuse, or operation of this product.
Service Under Warranty
During the warranty period, defective units will be repaired
or replaced (with the same or a comparable model), at
Whistler’s option, without charge to the purchaser when
returned with a dated store receipt to the address below.
Units returned without a dated store receipt will be handled
as described in section “Service Out Of Warranty.”
When returning a unit for service, please follow these
instructions:
1. Ship the unit in the original carton or in a suitable sturdy
equivalent, fully insured, with return receipt requested, and
shipping charges prepaid to:
Whistler Repair Dept.
551 N. 13th St.
Rogers, AR. 72756
Please allow 3 weeks for return.
24
pro200-400w.qxp 4/30/2010 9:07 AM Page 27

WARRANTY
Service Out Of Warranty
Units will be repaired at “out of warranty” service rates
when:
•The unit’s original warranty has expired.
• A dated store receipt is not supplied.
• The unit has been returned without its serial number.
• The unit has been abused, modified, installed
improperly, or had its housing removed.
The minimum out of warranty service fee for your Whistler
200 watt inverter is $15.00 (U.S.) and the 400 watt inverter
is $20.00 (U.S.). If you require out of warranty service,
please return your unit as outlined in the section “Service
Under Warranty” along with a certified check or money
order for the correct amount. Payment may also be made
by MasterCard, VISA and American Express; personal
checks are not accepted. In the event repairs cannot be
covered by the minimum service fee, you will be contacted
by a Whistler technical service specialist who will outline
options available to you. If you elect not to have your unit
repaired/replaced, it will be returned to you along with
your certified check or money order.
IMPORTANT:When returning your unit for service, be
certain to include a daytime telephone number.
Customer Service
If you have questions concerning the operation of your
Whistler inverter, or require service during or after the
warranty period, please call Customer Service at
1-800-531-0004. Representatives are available to answer your
questions Monday - Friday from 8:00 a.m. to 5:00 p.m. (CT).
26 27
pro200-400w.qxp 4/30/2010 9:07 AM Page 29