Product Specicaon
IMPORTANT: The luminaire must not be covered by any debris or insulang material. Ensure there is a minimum of 50mm air-
space around the luminaire and control gear. Electrical terminaon must be carried out by a qualied electrician in accordance
with the latest edion of the IEE wiring regulaons BS7671.
PLEASE RETAIN THIS GUIDE FOR FUTURE REFERANCE AND RECYCLE PACKAGING.
Dimensions
Round Wallwasher Square Wallwasher
Square Downlight
Round Downlight
85 mm bezel
Ø79 mm cut-out
85 mm bezel
Ø79 mm cut-out
85x85 mm bezel
79x79 mm cut-out
85x85 mm bezel
79 x79 mm cut-out
Specicaon
Lamp Type:- LED
Supply:-220-240V, 50-60Hz
Power Output:- 8W & 14W
Nominal Lumen Output:- 500 lm to 1000 lm
Colour Temperature:- 3000K & 4000K
Ingress Protecon:- IP44
Trim Colour:- RAL9003 Signal White
50mm
50mm
Airspace around luminaire and driver
50mm
GENERAL INFORMATION
1)A qualied electrician, in accordance with IEE wiring regulaons should carry out connecon to mains wiring.
2) Ensure that the rated voltage and frequency requirements are compable with the available mains supply.
3) Cleaning of reectors and lenses should be carried out using clean, so and lint free cloths and an-stac cleaning uid.
4) Do not carry out high voltage insulaon test, i.e. 500/1000v this may damage internal components.
50mm
ISOLATE MAINS SUPPLY BEFORE COMMENCING INSTALLATION
Ceiling thickness:- MINIMUM 3mm*, MAXIMUM 30mm
*A PATTRESS IS RECOMMENDED FOR CEILING THICKNESS LESS THAN 3mm .
A
C
Feed the driver and control gear into ceiling void,
ensuring it is not covered by debris or insulang
material and is correctly posioned.
D
E1
Reinstate mains
Apply a bead of quick drying grip adhesive to the rear
face of the plaster in frame.
Locate into hole.
Secure frame into hole using plaster in screws (by others)
Once adhesive has cured apply PVA bonding coat and
plaster up edge to frame.
Apply nish to ceiling and allow to dry. Plaster and paint
must be dried completely before installing luminaire
into plaster in frame. Otherwise this may invalidate
warranty.
B2
E2
*IMPORTANT :- To avoid damage to so ceiling types care
must be taken when releasing the spring into the aperture.
Squeeze ceiling springs and push the ng into the
ceiling void. It is important that the springs are held
from behind and only released once the luminaire is
in place. If there is a risk of the heatsink being covered
insert a yellow cap into the top of the luminaire.
Once in place make sure the luminaire is secure in the
ceiling.
Yellow Cap
Yellow Cap
Remove reector and
pull down on
Luminaire
IMORTANT– Align dot on luminaire to dot on frame before
aempng to lock ng into place.
Check the frame is clear of paint and plaster.
Push the ng into the frame. If there is a risk of the
heatsink being covered insert the yellow cap into the
top of the luminaire.
To remove luminaire for maintenance:-
Twist out reector then pull down on luminaire
Specicaon
Lamp Type:- LED
Supply:-220-240V, 50-60Hz
Power Output:- 8W & 14W
Nominal Lumen Output:- 500 lm to 1000 lm
Colour Temperature:- 3000K & 4000K
Ingress Protecon:- IP44
Trim Colour:- RAL9003 Signal White
Wire mains ex into driver according to the applicable
wiring diagram on the back of this leaet.
Connect ex to mains supply.
Round—Cut a 79mm circular hole using a hole saw.
Square– Cut a 79mm square hole .
To avoid damage to the ceiling les it is not recommended to remove the luminaire once installed into so ceiling types . The luminaire
and driver can be maintained from the adjacent ceiling le or by removing the whole le with luminaire aached.
Push
IMPORTANT: When installing wall wash type
luminaires the plaster in frame must be installed with
the dot facing the wall to be illuminated.
Remove Packaging
Push down on Luminaire to remove from the
plaster in frame.
B1
PLASTER IN ONLY
PLASTER IN ONLY METAL PAN / SOFT CEILING
TYPES* / PLASTER BOARD
