Whittier Wood Furniture 2002 User manual

Assembly Instructions
AEGAC = Glazed Antique Cherry finish; AEGSP = Glazed Spice finish;
AECAF = Caffè finish
2002 48"W McKenzie Alder
Bookcase Door Kit
Production Code:
02/10
P.O. Box 2827
Eugene, OR 97402 USA
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.
Before you begin your project, completely read the
Assembly Instructions.
For normal household use only. Not recommended
for commercial use.
Do not climb, sit or stand on this piece of furniture.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on
a cold and possibly damp cement floor).
Periodically inspect your furniture for any loose
glue joints, screws or any other problem that might
affect the stability of your furniture. Tighten or
repair as needed.
IMPORTANT NOTES:
Service Policy: We will replace any part that is
defective, missing or damaged during assembly.
Please contact Whittier Wood Products customer
service department directly by phone, fax, mail or
email for a replacement part.
To Order: Designate the finish, provide the furniture
model number found in the upper left corner of this page,
the part letter, production code, quantity needed, reason
for replacement, your full name, address and
telephone number.
Parts ship from our Eugene, Oregon factory within one
or two business days from the time we receive your
request. Please allow five to ten business days for delivery.
CALL US FIRST! Do not return this item to the store.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Hours: Our friendly customer service staff can be
reached Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific
Time). You may leave a message 24 hours a day,
seven days a week.

Before you begin to assemble this unit, identify each part and make sure the quantities received match what is on this list.
If you need to replace a part, please refer to the following list for the part name and letter code.
Glazed Antique Cherry finish (AEGAC) &
Glazed Spice finish (AEGSP) & Caffè finish (AECAF)
2002 48"W Door Kit — Parts List
A — Door — Qty. 4
B — Door Knob — Qty. 4 C — #8x1-1/2" Machine
Screw — Qty. 4
F — Pad — Qty. 4
D — Side Panel Hinge — Qty. 4
G — Vertical Panel Hinge — Qty. 4
E — Hinge Plate — Qty. 8
NOTE: The curve is taller on this piece than the Vertical Panel Hinge.
H — Washer — Qty.8
Top view of Side Panel Hinge (D) &
Vertical Panel Hinge (G)
Page 2 — 2002AEGAC_AEGSP_AECAF — 02/10

Tool required: Phillips Screwdriver
Page 3 — 2002AEGAC_AEGSP_AECAF — 02/10
Glazed Antique Cherry finish (AEGAC) &
Glazed Spice finish (AEGSP) & Caffè finish (AECAF)
2002 48" W Alder Bookcase Door Kit
— Assembly Instructions
2. Snap the handle of the Hinge (D or G) down on to each of the Hinge Plates (E or E/H) as seen
in Figures 2 and 2a.
1. Add washers to four of the eight Hinge Plates (E). You will attach the Vertical Divider Hinges (G) to
these Hinge Plates (E)/Washers (H) assemblies. See Figures 1a, 1b and 1c.
E or E/H D or G
Fig. 2 Fig. 2a
Fig. 1a Fig. 1cFig. 1b

Page 4 — 2002AEGAC_AEGSP_AECAF — 02/10
3.
Fig. 3
Fig. 3a
A
Lay two Doors (A) face down on a clean, protected surface. There are predrilled holes in the doors as
shown in Figure 3. This is where you will be inserting the hinge part of the assembly. Insert the Side Panel
Hinge (D) assembly that has the plastic knobs into the predrilled holes in the bottoms and tops of the Doors
(A). See Figures 3 and 3a. You must place both Side Panel Hinges (D) into the Doors before you
attach the doors to the bookcase.
Lay the other two Doors (A) face down on a clean, protected surface. There are predrilled holes in the
doors as shown in Figure 4. This is where you will be inserting the hinge part of the assembly. Insert the
Vertical Divider Hinge (G) assembly that has the plastic knobs into the pre-drilled holes in the bottoms and
tops of the Doors (A). See Figures 4 and 4a. You must place both Vertical Divider Hinges (G) into
the Doors prior to attaching to bookcase.
E
D
4.
Fig. 4
Fig. 4a
A
E/H
G

6.
Page 5 — 2002AEGAC_AEGSP_AECAF — 02/10
Side adjustment
Depth adjustment
To move the door towards the side panel/vertical divider, rotate screw ‘2’ counter-clockwise.
To move it away, rotate screw ‘2’ clockwise.
Loosen screw ‘1’ and adjust door. Re-tighten screw.
Height adjustment Loosen screws ‘3’ and adjust door. Re-tighten screws.
Fig. 6
1
2
3
3
The door may need to be adjusted so that all the spaces between the doors and unit sides are
equal. To make those adjustments, follow the instructions below. See Figure 6.
Fig. 5 Fig. 5a Center Shelf Fig. 5b
Side Panel
5. Attach the door with the Side Panel Hinges (D) to the side panels of the bookcase (see Fig. 5b)
by inserting the screws in the Hinge Plate (E) into the second and third holes up from the bottom of
the bookcase unit. See Figure 5. Attach the second Side Panel Hinge assembly to the same
door/bookcase by inserting screws ino the third and fourth predrilled holes down from the top of the
fixed centered shelf. See Figure 5a. Repeat the steps for other side.
Attach doors with Vertical Divider Hinges (G) and Washers (H) to each side of the vertical divider of
the bookcase in the same manner.
Bottom
Vertical
Divider
Fixed
Center
Shelf

7. Attach the Knobs (B) to the Doors (A) with #8x1-1/2 " Machine Screws (C). See Figure 5.
Door
C
B
8. Attach a Pad (F) to the back of each door where it comes in contact with the adjustable shelf.
F x 4
B x 4
Fig. 7
Page 6 — 2002AEGAC_AEGSP_AECAF — 02/10
C x 4