Whittier Wood Furniture 2091AFGSPb User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 07/13
Model #
2091AFGSPb;
2091AFCAFb
64"W Pacific
Sound Bar Console
AFGSP = Glazed Spice finish
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Do not climb, sit or stand on this piece of furniture.
Do not overload the drawers.
Unload items before you move this unit.
Before you load or move this unit, tighten all screws and supports.
Handle the glass plates with care. Glass is fragile.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Serious or fatal crushing injuries can occur from furniture tip-over. Use of
tip-over restraints may only reduce but not eliminate the risk of tip-over.
To help prevent tip-over:
Place heaviest items in the bottom drawers.
Unless specifically designed to accommodate, do not set TVs or other
heavy objects on top of this product.
Never allow children to climb or hang on drawers, doors or shelves.
Never open more than one drawer at a time.
Warning: At least one tipping restraint kit was included with your piece of
Whittier Wood Furniture. When you receive your furniture, be sure to find
and properly install the tipping restraint(s). If you cannot locate the
restraint(s), please contact us immediately for replacement.
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

2091AFGSPb; 2091AFCAFb 64"W Pacific Sound Bar Console
Parts List
2091AFGSPb_2091AFCAFb —Page 2 —07/13
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
A
Top (attached)
1
B
Adjustable Shelf (attached)
4
Cb
Case
1
D
Removable Back (installed)
2
E
Door Frame (installed)
2
F
Door Glass (attached)
2
Ga
Speaker Door (attached)
1
H
Small Drawer Box (inserted)
2
I L
Small Drawer Face (installed)
2
J M
Large Drawer Box (inserted)
3
K
Large Drawer Face (installed)
3
L
Glass Retainer (inserted)
1
M
Shelf Bracket (installed)
16
N
#6 x 1/2" Undercut Screw (inserted)
16
P
Butler Hinge (attached)
2
Q
Magnetic Push Lock (attached)
2
R
#5 x 5/8" Flat Head Screw (inserted)
12 (AFGSP)
0 (AFCAF)
T
#6 x 5/8" Undercut Screw AB (inserted)
4
U
Drawer Slides (pre-installed sets)
5
V
#6 x 3/4" Philtruss Screw (inserted)
30
W
#6 x 1/2" Philtruss Screw (inserted)
34
YA
#8 x 1-1/8" Lo-Profile Screw (inserted)
14

2091AFGSPb; 2091AFCAFb 64"W Pacific Sound Bar Console
Parts List
2091AFGSPb_2091AFCAFb —Page 3 —07/13
Part
Description
Quantity
YB
3mm x 12mm Pan Head Screw (inserted)
4
YC
1/4" x 20mm Insert Nut (inserted)
4
YD
#8 x 1-5/8" Machine Screw (installed)
10
YE
#8 x 1-3/8" Lo-Profile Screw (inserted)
6
YF
Adjustable Glide with Hex Nut (installed)
2
YG
Assembled Foot (attached)
2
YH
5/16" x 3/4" Insert Nut (inserted)
2
YI
Tuscan Magnetic Plate (attached)
2
YJ
#6 x 5/8" Undercut Screw ZN (inserted)
0 (AFGSP)
12 (AFCAF)
ZB
Small Adjustable Glide (installed)
4
ZC
#8 x 2" Black Screw (inserted)
4
ZD
Hinge (attached)
4
ZE
Hinge Plate (attached)
4
ZF
#6 x 3/4" P.O Screw (inserted)
16
ZG
Knob (attached)
2
ZH
#8 x 1-1/4" Machine Screw (installed)
2
ZI
Handle (attached)
5
ZK
Drawer Stop (attached)
4
ZL
Turn Button (attached)
8
ZM
#6 x 5/8" Philtruss Screw (inserted)
30
ZN
#8 x 1-1/4" Pan Head Screw (inserted)
34
ZP
#8 x 1-1/4" Black Screw (inserted)
29
ZQ
#8 x 1" Lo-Profile Screw (inserted)
20
ZR
Flat Washer (inserted)
2
ZS
Hex Bumper (attached)
2
ZT
Fitted Back (attached)
1
ZU
Speaker Spacer
2
ZV
Pad Strip (attached)
4

2091AFGSPb; 2091AFCAFb 64"W Pacific Sound Bar Console
Parts List
2091AFGSPb_2091AFCAFb —Page 4 —07/13
Part
Description
Quantity
ZW
Chain (attached)
2
ZX
Cleat (attached)
1
ZY
Push Plate
2
ZZ
1/2" Dark Antique Brad
4
TR
Furniture Tipping Restraint
2 sets

2091AFGSPb; 2091AFCAFb 64"W Pacific Sound Bar Console
Assembly Instructions
2091AFGSPb_2091AFCAFb —Page 5 —07/13
Tool Required: Phillips Screwdriver
1. Place the unit at its final destination. Rotate the Small Adjustable Glides (ZB) found at the
corners of the unit and the Adjustable Glide with Hex Nut (YF) at the bottom of the Assembled
Foot (YG) until the unit is level. See Figure 1.
Step two is optional: Attach the Push Plates (ZY) when the console will be placed in a high-use
area such as a retail sales floor where the Sound Bar Speaker Door (Ga) will be opened and closed
often.
2. Remove the Speaker Door (Ga) and place it face-up on a clean protected surface. Center a
Push Plate (ZY) over the right Tuscan Magnetic Plate (YI) and attach with two 1/2" Dark Antique
Brads (ZZ). Repeat for the left side. See Figure 2. Attach the Door.
Fig. 1
ZB
ZB
YF
YG
Fig. 2
ZY
ZZ
x 2
x 4
ZZ
ZY
YI
Ga
(back view)
ZZ
ZY
YI

2091AFGSPb; 2091AFCAFb 64"W Pacific Sound Bar Console
Assembly Instructions
2091AFGSPb_2091AFCAFb —Page 6 —07/13
3. To open the Speaker Door (Ga), simultaneously press the Push Plates or both corners until the
magnets release. Gently grasp the middle of the door and pull it open. To shut the door, push
gently but firmly on the Speaker Door (Ga) until the two Tuscan Magnetic Plates (YI) make
secure contact with the Magnetic Push Locks (Q).
If you did not install the Push Plates, gently press on both corners until the magnets release.
See Figure 3.
If you need to install your sound bar from the back, remove the #6 x 1/2" Philtruss Screws (W)
and pull away the fitted back (ZT). After installing the component, replace the Fitted Back and
attach with the #6 x 1/2" Philtruss Screws.
4. If your center sound bar needs to sit above the edge of the speaker door, place the two Speaker
Spacers (ZU) into the sound compartment so the Pad Strips (ZL) face down. Place the speaker
on top of the Spacers. See Figures 4 and 4a.
Fig. 4
Ga
ZU
ZU
Fig. 4a
ZU
Fig. 3
YI
ZT
Q
Ga
Q
YI

2091AFGSPb; 2091AFCAFb 64"W Pacific Sound Bar Console
Assembly Instructions
2091AFGSPb_2091AFCAFb —Page 7 —07/13
5. To insert your media components and access wires into the console more easily, you may want
to remove the Removable Backs (D). To do so, unlock the Turn Buttons (ZL) as shown in
Figures 5 and 5b. Slide the Backs away and place them off to the side. To put them back into
place, slide the Backs behind the Drawer Stops (ZK) and position the Turn Buttons so that they
are locked. See Figures 5a and 5b.
6. Determine where you want to place the Adjustable Shelves (B). To support each shelf, tap the
Shelf Brackets (M) into the four holes with the flat side down. Insert the shelf as shown in Figure
6. You may fasten the brackets to the shelf by inserting a #6 x 1/2" Undercut Screw (N).
Repeat for each shelf. See Figure 6a.
Fig. 6
N
M
Fig. 6a
Door removed for illustration purposes.
B
B
ZL
Locked
Position
Fig. 5
Fig. 5a
Unlocked
Position
Fig. 5b
ZT
ZK
ZL
D
D
ZK

2091AFGSPb; 2091AFCAFb 64"W Pacific Sound Bar Console
Assembly Instructions
2091AFGSPb_2091AFCAFb —Page 8 —07/13
7. To adjust the doors, follow the instructions below.
8. Tipping restraint: Locate two studs in the wall behind the unit. Attach a Clip (T1) to one wall
stud with two #8 x 2" Black Screws (T3). See Figure 8a. Attach a second clip to the unit with two
#6x5/8" Philtruss Screws (T5). See Figure 8b. Connect the two clips with the Nylon Restraint
Strap (T2). Pull the Nylon Restraint Strap (T2) tight so there is no slack. See Figures 8c and 8d.
Repeat this procedure to attach the second tipping restraint. If you cannot locate two studs,
purchase the proper wall attachment hardware for your type of wall and secure the unit.
Fig. 7a
1
Side adjustment 4mm (5/32")
To move the door towards the side
panel, loosen screw ‘1’and tighten
screw ‘2’. To move the door away
from the side panel, loosen screw
‘2’ and tighten screw ‘1’.
Depth Adjustment 4mm (5/32")
Loosen screw ‘2’ (just one turn),
adjust the door to the desired position
and tighten the screw.
Height Adjustment 4mm (5/32")
Loosen screw ‘3’, adjust the door to
the desired position and tighten
the screw.
3
3
2
Door
Hinge
Arm
ZD
Fig. 7
ZE
2
Fig. 8a
T1
T3
Pull tight
Fig. 8d
T1
T2
T5
Fig. 8c
Pull the Nylon Restraint
Strap (T2) tight
so there is no slack.
T3
T5
T1
Fig. 8b