Whittier Wood Furniture 2225AST User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 07/18
Model #
2225AST
Ellison Cal-King
Panel Storage Bed
AST = Astoria Sky finish
Assembly Instructions
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Remove items before you move this unit.
Do not overload the drawers.
This assembly requires two people.
WARNING
Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the state of California to cause cancer.
Avoid inhaling wood dust or use a dust mask or other safeguards for
personal protection.
For more information go to: www.p65warnings.ca.gov/wood
This product can expose you to chemicals, including formaldehyde,
which are known to the State of California to cause cancer.
For more information go to: www.p65warnings.ca.gov/furniture
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CUSTOMER SERVICE
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
Fax: [phone]• Email: [e-mail]
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.

2225AST Ellison Cal-King Panel Storage Bed
Parts List
2225AST —Page 2 —07/18
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
2227AST
Ellison Cal-King Panel Headboard/Footboard Kit (x1)
Part
Description
Quantity
A
Headboard Assembly
1
B
Footboard Assembly
1
J
#8 x 7/8" Black Lo-Profile Screw (inserted)
25
K
#8 x 1-1/4" Black Screw
24
W
5/16" x 14mm Insert Nut (inserted)
8
ZC
5/16" x 2-1/4" Hex Bolt
6
ZD
5/16" x 35mm Hex Bolt
18
ZE
1/4" Flat Washer
24

2225AST Ellison Cal-King Panel Storage Bed
Parts List
2225AST —Page 3 —07/18
2226AST
Ellison Cal-King Pedestal Kit (x2)
Part
Description
Quantity
C
Pedestal
1
D
Drawer Box (assembled)
3
E
Drawer Face (attached)
3
F
Left/Right Center Deckboard
1
G
20" Drawer Slides (installed)
3 sets
H
#6 x 3/4" Philtruss Screw (inserted)
18
I
#6 x 1/2" Philtruss Screw (inserted)
18
J
#8 x 7/8" Black Lo-Profile Screw (inserted)
18
K
#8 x 1-1/4" Black Screw (inserted)
8
L
#8 x 1-5/8" Black Screw (inserted)
24
M
#8 x 1-5/8" Machine Screw Tuscan (installed)
6
O
Antique Pewter Pull (attached)
3

2225AST Ellison Cal-King Panel Storage Bed
Parts List
2225AST —Page 4 —07/18
2228AST
Ellison Cal-King Base Kit (x1)
Part
Description
Quantity
P
Mitered End Support
1
Q
Square End Support
2
R
Left Support
1
S
Right Support
1
T
Cal-King Trestle Rail (26-7/8")
4
U
#8 x 1-3/4" Pan Head Screw (inserted)
12
V
#10 x 3/4" Pan Head Screw (inserted)
16
W
5/16" x 14mm Insert Nut (inserted)
18
X
Wood Dowel (inserted)
12
Y
Foot Bracket (attached)
4
ZA
Adjustable Glide (installed)
4

2225AST Ellison Cal-King Panel Storage Bed
Assembly Instructions
This assembly requires two people.
2225AST —Page 5 —07/18
Tools Required: Phillips screwdriver, 1/2" open end or box end wrench.
1. Set aside part Trestle Rail (T) for use later in the assembly process. Use the notch and dowels
on Square End Support (Q) and Mitered End Support (P) as a guide attach to the Right Support
(S) using the Hex Bolts (ZC) and Washers (ZE) from the Headboard/Footboard Kit. See Figures
1 and 1a.
2. Attach the assembly to the Left Support (R) Using Hex Bolts (ZC) and Washers (ZE). See
Figures 2 and 2a. Identify the Headboard end of the assembly and place near the final bed
location. See drawing below.
Fig. 2
R
Q
Q
ZE
ZC
x 3
x 3
P
Footboard
Headboard
Fig. 2a
ZE
ZC
Fig. 1
Q
Q
S
ZE
ZC
x 3
x 3
Fig. 1a
ZE
ZC
P

2225AST Ellison Cal-King Panel Storage Bed
Assembly Instructions
This assembly requires two people.
2225AST —Page 6 —07/18
3. Place each pedestal on top of the base kit against the side of and between the locater blocks of
the Base Kit. See Figure 3.
Fig. 3
C
Locater blocks
Locater blocks
Headboard end of Base
has leveler outside the
crosspiece

2225AST Ellison Cal-King Panel Storage Bed
Assembly Instructions
This assembly requires two people.
2225AST —Page 7 —07/18
4. Open the drawers and attach the pedestal to the base using Hex Bolts (ZD) and Washers (ZE)
only finger tight. See Figures 4 and 4a.
Fig. 4
Fig. 4a
(Notched Deckboards removed for illustration purposes)
ZE
ZD
ZE
ZD
x 10
x 10

2225AST Ellison Cal-King Panel Storage Bed
Assembly Instructions
This assembly requires two people.
2225AST —Page 8 —07/18
5. NOTE: When attaching the Footboard (B) to the Pedestal/Base assembly attach it at the end of
the Base with the leveler behind the crosspiece.
There are two options to attach the Footboard (B) to the Pedestal Assembly. Option a) Release
the two drawers (D) at the end of the assembly as shown in Fig. 5a. Open the Drawers (D) until
the back edge of the drawer is even with the front of the Pedestal. Reach under the attached
deckboard from the backside of the pedestal and insert Bolts (ZD) and Washers (ZE) into the
Footboard (B). Push the drawers closed. Option b) remove the two end drawers (D) completely.
Insert the bolts and washers into the Footboard and reinstall the drawers. See Fig. 5b, 5c.
Fig. 5c
ZE
ZD
x 4
x 4
Fig. 5b
ZE
ZD
Option 5b shown in illustration
Fig. 5
Drawer Release Lever
Fig. 5a
Headboard end of Base
has leveler outside the
crosspiece
B

2225AST Ellison Cal-King Panel Storage Bed
Assembly Instructions
This assembly requires two people.
2225AST —Page 9 —07/18
6. Attach the Headboard (A) with Hex Bolts (ZD) and Washers (ZE) using assembly option a) or b)
from Step 5. See Figures 6 and 6a.
Fig. 6
ZE
ZD
x 4
x 4
Fig. 6a
ZD
ZE
Option 5b shown in illustration

2225AST Ellison Cal-King Panel Storage Bed
Assembly Instructions
This assembly requires two people.
2225AST —Page 10 —07/18
7. Once the Headboard and Footboard are attached, open all drawers and tighten Hex Bolts (ZD)
and Washers (ZE) on the inside of the bed assembly.
8. Adjust levelers (ZA) only if floor is uneven or if bed has movement . See Figures 8 and 8a.
Fig. 8
Fig. 8a
ZA
(Drawers and Bottom Boards removed for illustration purposes)

2225AST Ellison Cal-King Panel Storage Bed
Assembly Instructions
This assembly requires two people.
2225AST —Page 11 —07/18
9. Insert Cal-King Trestle Rail Supports (T). See Figures 9 and 9a.
10. Place the Left/Right Center Deckboards (F) as shown in Figure 10 and secure with
twenty-four #8x1-1/4" Black Screws (K). There should be a small gap between each deckboard.
See Figure 10.
Fig. 10
K
x 24
K
F
Fig. 9
Fig. 9a
T