Whittier Wood Furniture John Greenleaf 371KFDC User manual

For normal household use only.
recommended for commercial use.
Do not climb, sit or stand on this piece of
furniture.
Production Code:
Service Policy: We will replace any parts
which are defective, missing or damaged
during assembly. Please contact Whittier
Wood Products customer service department
directly (by phone, fax, mail or email) for
replacement parts.
Hours: Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order: Provide the complete furniture
model number (upper left corner of this
page), part letter, production code, quantity
needed, reason for replacement and your full
name and address along with a telephone
number in case we need to contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
Outside U.S. or Canada: 541-687-0213
Outside U.S. or Canada: 541-687-0213
Fax: [phone] • Email: [e-mail]
Fax: [phone] • Email: [e-mail]
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
P.O. Box 2827
Eugene, OR 97402 USA
Natural characteristics
such as knots provide
a natural feel.
Model #
371KFDC
DISTRESSED ANTIQUE CHERRY FINISH
Rustic Lodge Table
Assembly Instructions
Rev. 10/05
Congratulations!
This fine piece of furniture will make a handsome
addition to your home. For the best results, start by
reading the Assembly Instructions completely before
you begin your project. Read the Assembly Instructions completely before
beginning.
Store the parts: 1) in their box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may
be affecting the stability of your furniture. Tighten or
repair as needed.

PAGE 2 — 371KFDC
371KFDC Rustic Lodge Table – Parts List
BEFORE BEGINNING ASSEMBLY:
Check that the quantities of the parts received match those on parts list below.
A — Table Top — Qty. 1
B — Top Support — Qty. 2
D — Foot — Qty. 2
C — Leg — Qty. 2
E — Middle Support — Qty. 1
F — Wood Wedge — Qty. 4
H — 5/16" Washer — Qty. 8
J — Tack Glide — Qty. 4
I — #12 x 2" Pan Head
Screw — Qty. 20
G — 3" x 5/16" Lag Bolt — Qty. 8

1) Pound the Tack Glides (J) into the bottom of the Feet (D).
Using the 3" Lag Bolts (G) and 5/16" Washers (H), attach a Top Support (B) and Foot (D) to each
Leg (C). Tighten the bolts firmly.
FIG. 1
FIG. 1A
2) Slide the Middle Support (E) into the holes in the middle of each leg. Note that the holes for the
wedges in the Middle Support are tapered. Using padding on a hammer to prevent damaging the
wood, tap the Wood Wedges (F) into the larger openings until snug.
FIG. 2 FIG. 2A
J
J
B
C
D
H
GH
G
H
G
H
G
EF
F
F
F
D
371KFDC — PAGE 3
371KFDC Rustic Lodge Table
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED:
Phillips screwdriver, Hammer, 5/32" Drill Bit, Drill, Tape Measure, 1/2" Socket.

3) Center the leg assembly on the bottom of the Table Top (A). Insert the #12 x 2" Screws (I)
through the holes in the Top Support (B). Tap them lightly to mark the screw locations on the
bottom of the Table Top.
Move the leg assembly aside and drill 5/32" pilot holes one inch deep.
Put the leg assembly back in place and tighten the screws down firmly.
FIG. 3
I
A
I
B
B
PAGE 4 — 371KFDC