Whittier Wood Furniture McKenzie 1306AFGAC User manual

1306AFGAC & 1306AFCAF
McKenzie Full Storage Bed
Unload items before you move this unit.
Production Code:
05/10
VN
Model #
Assembly Instructions
P.O. Box 2827
Eugene, OR 97402 USA
.
Before you begin your project, completely read the
Assembly Instructions.
.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on a
cold and possibly damp cement floor).
Periodically inspect your furniture for any loose
glue joints, screws or any other problem that might
affect the stability of your furniture. Tighten or
repair as needed.
IMPORTANT NOTES:
Service Policy: We will replace any part that is
defective, missing or damaged during assembly.
Please contact Whittier Wood Products customer
service department directly by phone, fax, mail or
email for a replacement part.
To Order: Designate the finish, provide the furniture model
number (upper left corner of this page), the part letter,
production code, quantity needed, reason for replacement,
your full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one
or two business days from the time we receive your
request. Please allow five to ten business days for delivery.
CALL US FIRST! Do not return this item to the store.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Hours: Our friendly customer service staff can be
reached Monday-Friday 7:00 a.m. to 5:00 p.m.
(Pacific Time). You may leave a message 24 hours
a day, seven days a week.
For normal household use only.
This assembly requires two people.
Do not overload the drawers.
Not recommended
for commercial use.
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish

1306AFGAC & 1306AFCAF McKenzie Full Storage Bed — Parts List
Page 2 — 1306AFGAC_1306AFCAF — 05/10
1308AFGAC & 1308AFCAF (x2)
N — #8 x 1-1/2" Machine Screw
— Qty. 3
O — Knob — Qty. 3
I — Pedestal Kit — Qty.1
P — Deckboard — Qty.1
J — Small Drawer Box
— Qty. 1 (assembled)
K — Large Drawer Box
— Qty. 2 (assembled)
L — Small Drawer Face
— Qty. 1 (attached)
M — Large Drawer Face
— Qty. 2 (attached)
Q — Drawer Slides — Qty. 3
(attached sets)
T — #8 x 2" Black Screw
— Qty. 16 (inserted)
ZQ — Left Bracket
— Qty. 2 (attached)
ZR — Right Bracket
— Qty. 2 (attached)
ZP — #8 x 1" Black Screw
— Qty. 16 (inserted)
ZW — #6 x 1/2" Undercut
Screw — Qty. 30 (inserted)
Y — #8 x 7/8" Lo-Profile
Screw — Qty. 16 (inserted)
E — #8 x 1-1/4" Black Screw
— Qty. 30 (inserted)
ZX — #8 x 1-5/8" Black
Screw — Qty. 12 (inserted)
1309AFGAC & 1309AFCAF (x1)
A — Headboard — Qty.1
B — Footboard — Qty.1
C — Trestle Without T-Nuts — Qty.4
D — Trestle With T-Nuts — Qty.8
F — 1/4" x 1-3/4" Hex Bolt
— Qty. 16
G — 1/4" x 2-1/2" Hex Bolt
— Qty. 16
H — Washer — Qty. 32
E — #8 x 1-1/4" Black Screw
— Qty. 36 (12 inserted)
T — #8 x 2" Black Screw
— Qty. 6
ZU — 1/4" T-Nut
— Qty. 32 (inserted)
ZQ — Left Bracket
— Qty. 4 (attached)
ZR — Right Bracket
— Qty. 4 (attached)
ZP — #8 x 1" Black Screw
— Qty. 32 (inserted)
ZV — #8 x 20mm Pan Head
Screw — Qty. 47 (inserted)
ZX — #8 x 1-5/8" Black Screw
— Qty. 4 (inserted)
U — Foot Assembly
— Qty. 2
ZY — Foot Bracket
— Qty. 2 (attached)
V — Leveler Bracket
— Qty. 2 (installed)
W — Adjustable Glide
— Qty. 2 (installed)
Please identify the parts and check that quantities received match what is on this list.
If you need to replace a part, refer to the following letter and item name.

1306AFGAC & 1306AFCAF
McKenzie Full Storage Bed
Assembly Instructions
Page 3 — 1306AFGAC_1306AFCAF — 05/10
This Assembly Requires Two People
Tools Required: Phillips screwdriver, 7/16" wrench, tape measure
Remove the Trestles (C and D) from the back of the Headboard as seen in Figure 1 and
place them off to the side. Remove the foot assemblies (U) from the back of the Footboard (B)
and set them off to the side.
1.
Place both Pedestals (I) approximately 57" apart as shown in Figure 2.2.
Fig. 1
Fig. 2
Shipping Straps
I
I
57"
D
C

Page 4 — 1306AFGAC_1306AFCAF — 05/10
Remove the Drawers (J & K) from the Pedestal Kits (I). To remove the drawers, pull up on
the left side of the Drawer Release Lever while pushing down on the right Drawer Release Lever.
See Figure 3a. Note where each drawer came from to ensure correct installation. Positions are
marked on drawer bottoms.
3.
Fig. 3
Fig. 3a
Drawer Release Lever
Place four Trestles with T-Nuts (D) between the Pedestals (I) and insert and hand-tighten
1/4 x 1-3/4" Bolts (F) and Washers (H) as shown in Figure 4a. When installing the Trestles (D),
make sure the T-nuts face out as shown in Figure 4.
NOTE: Do not tighten the bolts with a wrench until the final assembly in
step 10 is completed. Hand-tighten only.
4.
Fig. 4a
Trestle with T-Nuts (D)
F x 16 H x 16
H
F
Fig. 4
T-Nuts face out
D
D
D
D
I
I

Page 5 — 1306AFGAC_1306AFCAF — 05/10
5. Rotate the Pedestal Assembly upside down so the plywood deckboards are on the floor.
Fig. 6a
G x 16 H x 16
Fig. 6
D
D
D
D
C
CC
C
6. Position the remaining Trestles (C and D) on the Pedestal Assembly. Face the Trestles with
T-Nuts (D) toward the ends of the Assembly from the center as shown in Figure 6. Insert and
hand-tighten the 1/4" x 2-1/2" Hex Bolts (G) and Washers (H). See Figures 6 and 6a.
Fig. 5
R
o
t
a
t
e
P
e
d
e
s
t
a
l
A
s
s
e
m
b
l
y
u
p
s
i
d
e
d
o
w
n
s
o
t
h
a
t
t
h
e
p
l
y
w
o
o
d
D
e
c
k
b
o
a
r
d
s
a
r
e
o
n
t
h
e
f
l
o
o
r
.
NOTE: Do not tighten the bolts with a wrench until the final assembly in
step 10 is completed. Hand-tighten only.

Page 6 — 1306AFGAC_1306AFCAF — 05/10
Rotate the Pedestal Assembly to its original position.
Fig. 7
Fig. 7a
D
D
CC
T x 6
7.
8.
On each inner Pair of Trestles (C & D), place a Foot Assembly (U) between the two middle
trestles as shown in Figure 7. Attach with three #8 x 2" Black Screws (T), making sure the screws
go all the way through the trestle and into the foot assembly as shown in Figure 7a.
U
Fig. 8
R
o
t
a
t
e
P
e
d
e
s
t
a
l
A
s
s
e
m
b
l
y
t
o
i
t
s
o
r
i
g
i
n
a
l
p
o
s
i
t
i
o
n
.
V
W
T

Page 7 — 1306AFGAC_1306AFCAF — 05/10
Fig. 10
A
Attach the Footboard (B) to the Pedestal Assembly as in Figure 9. Align the brackets as shown
in Figure 9a and slide the Pedestal Assembly down on to the Footboard (B).
9.
Fig. 9a
Fig. 9
B
Adjust the Glides (W) on the Foot Assemblies (U) so the Glides just touch the floor.11.
Fig. 11
Adjustable Glide (W)
Leveler Bracket (V)
Attach the Headboard (A) to the Pedestal Assembly as in the previous step.
NOTE: Now use a wrench and tighten all of the bolts on the trestles.
10.

Page 8 — 1306AFGAC_1306AFCAF — 05/10
Place Deckboards (P) as shown in Figure 13. There should be a small gap between each
each deckboard. Secure with #8x1-1/4" Screws (E).
13.
Fig. 13
E x 24
P
14.
12.
Fig. 12
To make sure the bed is square, measure the distance between opposing corners. If one of the
measurements is larger, tap on a footboard leg until the measurement is equal. See Figure 12.
Markings are on drawer bottoms. Carefully align drawer slides into the cabinet and
gently push them back to their original positions. Sleep well, and enjoy!