Whittier Wood Furniture McKenzie Alder 1525AUF User manual

P.O. Box 2827
Eugene, OR 97402 USA
Outside U.S. or Canada: 541- 687- 0213
800-653-3336
Fax: [phone] • www.whittierwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A
For normal household use on ly.
recommended for commercial us e.
Congratulations!
Production Code:
Assembly Instructions
Model #s
Model #s
Model #s
AUF McKenzie Alder
24" Wide
30" Wide
36" Wide
Bookcases with Doors
Service Policy: We will replace parts
which are defective, missing or damaged.
Please contact Whittier Wood Products
customer service department directly (by
phone, fax, mail or E-mail) for replacement
parts.
Hours: Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order: Provide the complete furniture
model number, part letter, production code,
quantity needed, reason for replacement
and your full name and address along with
a telephone number in case we need to
contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
This fine piece of furniture will make a handsome
addition to your home. For the best results, start
by reading the Assembly Instructions and Finishing
Hints before you begin your project.
Completely read the Assembly Instructions and
Finishing Hints before you begin your project.
Store the item: 1) in the box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
If there is a problem with a hinge, do not attempt to
remove without first contacting Customer Service.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
Rev. 02/09
Do not climb, sit or stand on this piece of
furniture.
Unload items from this unit prior to moving.
Do not overload shelves on this unit.
Before loading or moving this unit, check all screws
and supports for tightness.
For maximum stability, attach unit to the wall using
the enclosed hardware as per instructions.
24" x 72"
24" x 84"
30" x 84"
1525AUF 1527AUF
1535AUF 1537AUF
1545AUF 1547AUF
30" x 72"
36" x 84"
36" x 72"

Page 2 — M_24-36w_72-84h_1525-1547AUF — Rev. 02/09
McKenzie 1525-1547AUF Alder Bookcase
with Doors — Parts List
1525AUF
(Shown)
A
D
A
A
J
D — Top Assembly —
Qty. 1 (installed)
E — Furniture Tipping
Restraint — Qty. 1
F — Tack Glide
— Qty. 2 (inserted)
G — #8 x 1" Pan Head Screw — Qty. 8 (inserted)
I — Small Adjustable Glide (installed) — Qty. 2
J — Door — Qty. 2 (installed)
K — Hinge — Qty. 4 (installed)
L — Base Plate — Qty. 4 (installed)
H — Nylon Insert — Qty. 2 (inserted)
M — Knob — Qty. 2 (installed)
N — #8 x 1½" Machine Screw — Qty. 2 (installed)
Tools Required: Phillips Screwdriver, Rubber Mallet or Padded Hammer
1.
TO MOVE THE ADJUSTABLE SHELVES:
Determine where you want to place the Adjustable Shelves (A). Remove the #6x½" Undercut Screws (C) from the
underside of the shelf and take out the Shelf and Shelf Brackets (B). Tap the Shelf Brackets (flat side down) into the four
different holes and reinsert the shelf. You may refasten them by inserting #6x½" Undercut Screws (C).
2. Level the unit using the Adjustable Glides (I) located on the bottom of the unit.
3. When you have determined the location for your unit, install the Furniture Tipping Restraint (E). Carefully follow the
instructions on the package. If you cannot locate a stud, purchase the proper tipping restraint for your type of wall
and install.
4. If there is a problem with a Hinge (K), do not attempt to remove it. Contact Customer Service first.
A —
Adjustable Shelf (installed)
1525AUF
1535AUF
1545AUF
1537AUF
1547AUF
Model #
1527AUF
Qty. 4
}
Qty. 5
}
B —
Shelf Bracket (inserted)
1525AUF
1535AUF
1545AUF
1537AUF
1547AUF
Model #
1527AUF
Qty. 16
}
Qty. 20
}
C — #6 x ½" Undercut Screw (inserted)
1525AUF
1535AUF
1545AUF
1537AUF
1547AUF
Model #
1527AUF
Qty. 16
}
Qty. 20
}
Identify parts listed below and check that the quantities match what you’ve received.
If you need to replace a part, please refer to its name and letter.
3
2
3
1
Side adjustment 4mm (5/32")
TO ADJUST THE DOORS:
To move the door towards the side
panel, loosen screw "1" and tighten
screw "2". To move the door away
from the side panel, loosen screw
"2" and tighten screw "1".
Depth Adjustment 4mm (5/32")
Loosen screw "2" (just one turn).
Adjust door to desired position and
retighten screw.
Height Adjustment 4mm (5/32")
Loosen screw "3", adjust door to
desired position and retighten screw.

Rubber
gloves
Rags
Paper towels
Q-tips
Tack cloth
Drop cloth
Paint brushes
(bristle and
foam)
#220 & #320
sandpaper
Mineral spirits
Masking Tape
Rev. 8/07
Finishing Hints
Choosing the Finish:
Getting Started
1. Choose a finish that will meet your expectations for
the product you are finishing. Are you matching
existing furniture or do you want a “natural” finish?
Is the piece to be functional, decorative or both?
The answers to these questions may affect the
type of finish you choose.
1. Assembly Instructions may contain special
finishing information for that item. Read both
the Assembly Instructions and these Finishing
Hints completely before beginning.
2. Sand the entire piece, using #220 grit sandpaper.
Sand with the grain of the wood on flat surfaces
and opposite the grain on turnings. Some parts
are plywood. Be careful not to sand through the
veneer. End grain (table top ends, seat edges,
grooves on turnings, etc.) accepts more stain.
Extra sanding in these areas with a #320 grit sand-
paper will reduce stain absorption, creating a more
evenly stained piece.
3. When sanding is completed, wipe the surface of
your furniture with a cloth or tack rag. Make sure
the item is free of dust before proceeding.
2.
Use products of the same brand to ensure compat-
ibility of products.
4. We recommend using a wood conditioner under oil
base stains.
5. Work in a well ventilated and well lit area.
3.
ALWAYS follow the stain manufacturer’s instruc-
tions. Alder is a porous hardwood
and often
looks best when following the finishing directions
for softwoods
1. Read and follow label directions. Stir stain well
before starting.
4. Q-tips are ideal for hard to reach areas.
5. Allow to dry thoroughly before proceeding.
2.
Test stain on an inconspicuous spot on your proj-
ect, or use the sample chip if one is provided. The
sample chip must be sanded in the same way as
your furniture kit to ensure the piece will accept the
stain similarly. Put at least one coat of your top coat
over the stain sample, as it also affects the look of
the stain. Test every type of wood that is in your
kit. Some of our products include more than one
type of wood, which may react differently to the
stain color. Sample chips for the different woods
may be included. It may be necessary to add a
second coat of stain to lighter woods to match the
darker woods in your kit.
3. Apply stain with a poly brush or lint-free cloth. Apply
stain over a small area and wipe off excess. Work-
ing in small areas will make the color easier to con-
trol.
1. Always read and follow all label directions. Stir
your finish coat gently, do not shake. It will create
bubbles that are hard to remove.
2. All surfaces (including the underside of table tops
and inside drawers) must be sealed with at least
one layer of a top coat. This will help minimize
wood swelling, shrinkage, warping and cupping
due to changes in moisture content or temperature.
3. We recommend that you apply a minimum of two
coats when using polyurethane or varnish
(especially on all table top and work surfaces).
Sand lightly between coats using a #320 grit sand-
paper or 00 steel wool for the smoothest possible
finish.
4.
Some water-based finishes tend to raise the grain
slightly. This can be easily controlled with this sand-
ing step. However, do not use steel wool when using
water-based finishes. Strands of steel fiber caught
in the wood can cause rust spots when coated with
any water-based product.
1. For best results when painting, first coat the wood
with a primer. An oil based primer would be best for
a smooth finish. If you do not wish to use a solvent
based primer, a water based primer would work
almost as well.
2. Buy a quality brand paint. You may use a satin,
semi-gloss, or gloss sheen. Apply a second coat
for a smooth finish. Lightly sand between coats
using a #320 grit sandpaper, so that the second
coat will bond well. Repeat as desired.
3. Since there is such a variation between paint
manufacturers, refer to your paint supplier for spe-
cific advice on using the paint that you purchase.
Staining
Applying the Top Coat:
Painting:
No top coat is required if using paint.