Whittier Wood Furniture Pacific Queen 1448AFCAF User manual

Production Code:
11/09
VN
P.O. Box 2827
Eugene, OR 97402 USA
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.
Service Policy: We will replace any part that is
defective, missing or damaged during assembly.
Please contact Whittier Wood Products customer
service department directly by phone, fax, mail or
email for a replacement part.
To Order: Provide the furniture model number (upper
left corner of this page), the part letter, production
code, quantity needed, reason for replacement, your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one
or two business days from the time we receive your
request. Please allow five to ten business days for delivery.
CALL US FIRST! Do not return this item to the store.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Hours: Our friendly customer service staff can be
reached Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific
Time). You may leave a message 24 hours a day,
seven days a week.
Before you load or move this item, check to make
sure all screws and supports are tight.
This assembly requires two people.
.
Before you begin your project, completely read the
Assembly Instructions.
For normal household use only. Not recommended
for commercial use.
Unload items from this unit prior to moving.
Do not overload the drawers in this unit.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40° to 90° (not on a
cold and possibly damp cement floor).
Periodically inspect your furniture for any loose
glue joints, screws or any other problem that might
affect the stability of your furniture. Tighten or
repair as needed.
IMPORTANT NOTES:
Assembly Instructions
Model #
Pacific Queen Storage Bed
Caffè finish
1448AFCAF

1448AFCAF Pacific Queen Storage Bed — Parts List
1451AFCAF (x1)
1449AFCAF (x2)
Page 2 — 1448AFCAF — 11/09
K — Angle Bracket
— Qty. 2 (attached)
E — 5/16" Washer
— Qty. 8
H — 1/4" Washer
— Qty. 12
N — Pedestal Kit
— Qty.1
A — Headboard — Qty.1
B — Footboard — Qty.1
O — Drawer Box
— Qty. 3 (assembled)
P — Drawer Face
— Qty. 3 (attached)
C — Foot Assembly
— Qty. 6
M — Adjustable Glide
— Qty. 6 (installed)
U — Hanger Bolt
— Qty. 6 (inserted)
V — Insert Nut
— Qty. 8 (inserted)
S — Hex Wrench
— Qty. 1
I — Barrel Nut
— Qty. 2
J — 9.5mm x 25mm
Wood Dowel — Qty. 2
T — T-Nut
— Qty. 6 (inserted)
L — #6 x 3/4" Flat Head Screw
— Qty. 12 (6 inserted)
G — ¼" x 1¾" Hex Bolt
— Qty. 12
F — 1/4" x 80mm
Hex Bolt — Qty. 2
D — 5/16" x 2¼" Hex Bolt
— Qty. 8
Please identify the parts and check that quantities received match what is on this list.
If you need to replace a part, refer to the following letter and item name.
X — #7 x 1½" Black Pan
Head Screw — Qty. 79 (inserted)
Y — #6 x ½" Undercut
Screw — Qty. 36 (inserted)
Z — #8x1" Lo-Profile
Screw — Qty. 18 (inserted)
ZD — #6x1/2" Philtruss
Screw — Qty. 24 (inserted)
ZA — #6x1-1/4" Pan Head
Screw — Qty. 12 (inserted)
ZB — 8x20mm Pan Head
Screw — Qty. 12 (inserted)
ZC — Small Angle Bracket
— Qty. 4 (attached)
R — Drawer Slides
— Qty. 3 (installed sets)
T — T-Nut
— Qty. 9 (inserted)

1448AFCAF Pacific Queen Storage Bed
Assembly Instructions
Page 3 — 1448AFCAF — 11/09
This Assembly Requires Two People
Remove the Drawers (O) from the Pedestal Kits (N). To remove the drawers, pull up on the left
Drawer Release Lever while pushing down on the right Drawer Release Lever. See Figures
1 and 1a. Note where each drawer came from to ensure correct reinstallation. Positions are
marked on the drawer bottoms.
1.
Fig. 1
Fig. 1a
Drawer Release Lever
Tools Required: Hex Wrench (provided), Phillips Screwdriver, Slotted Screwdriver
1/2" Wrench, 7/16" Wrench, Tape Measure, Wood Glue, Rubber Mallet or Padded Hammer
2.
Fig. 2
x 12
x 12
G
H
To protect your flooring and the surface of the unit, place the Pedestal Kits (N) face-down on the
opened and unfolded 1449 cartons as shown in Figure 2. (When you join the pedestals, carpet fibers
can get caught in between the middle supports.) Place twelve ¼" Washers (H) over twelve ¼"x1¾"
Hex Bolts (G) and thread each through a pre-drilled hole and into a T-Nut in the middle support
found on each pedestal. Finger tighten each bolt, making sure the pedestals line up with each other.
Using a 7/16" wrench, securely tighten each bolt. See Figure 2.
HG
G
H
T
O
unfolded 1449 cartons
N
T
TTT

3. Rotate the Adjustable Glides (M) so that the Foot Assemblies (C) are 4½" tall as shown in Figure 3a.
Attach the six Foot Assemblies (C) as shown in Figure 3.
4. This step requires two people to move the bed to its upright horizontal position.
Rotate the bed so the deck boards are face-up. DO NOT PLACE UNDUE PRESSURE ON THE
FOOT ASSEMBLIES. See Figure 4.
5. Spread a thin film of glue in the dowel holes at one end of the top cap of the bed. Insert two
dowels (J) and gently tap with a rubber mallet. Quickly wipe away any excess glue. See Figures
5 and 5b.
Fig. 3
Fig. 3a x 6
C
C
4½"
Page 4 — 1448AFCAF — 11/09
Fig. 5
Fig. 5a
x 2
J
J
JJ
M
Fig. 4
Top cap Top cap

Page 5 — 1448AFCAF — 11/09
Fig. 6
Fig. 6a Fig. 6b
x 4
x 4
D
E
DE
B
J
J
DE
B
J
J
Fig. 7
x 4
x 4
D
E
D
E
6.
7. Position the Headboard (A) against the end of the pedestal assembly. Place four 5/16" Washers (E)
four 5/16" x 2¼" Hex Bolts (D) and thread the washer/bolts through the pre-drilled holes in the
Pedestal Assembly and into the Headboard. Tighten the bolts with a 1/2" wrench. See Figure 7.
Top cap
Position the Footboard (B) against the end of the pedestal assembly and insert the dowels (J) into the
oval holes in the top cap of the footboard. Place four 5/16" Washers (E) over four 5/16" x 2¼" Hex
Bolts (D) and thread the washer/bolts through the pre-drilled holes in the Pedestal Assembly and
into the Footboard. Tighten the bolts with a ½" wrench. See Figures 6, 6a and 6b.

Fig. 8
Fig. 8a
Fig. 8b
x 6
L
L
x 2
F
x 2
I
I
F
I
L
Page 6 — 1448AFCAF — 11/09
F
F
Fig. 9
Check the drawer bottoms for their correct positions. Carefully align the drawer slides and gently
insert the six drawers. Sleep well and enjoy!
9.
K
KC
Secure the preattached Angle Brackets (K) on the Headboard to the Pedestal Assembly with six
#6 x ¾" Flat Head Screws (L). See Figures 8 and 8a. Insert one Barrel Nut (I) into the pre-drilled hole
on the bottom of the left pedestal rail. Using a slotted screwdriver, line up the hole in the Barrel Nut
to the hole in the Headboard. Insert one 1/4" x 80mm Hex Bolt (F) into the pre-drilled hole in the
Headboard and tighten with the provided Hex Wrench (S). Repeat for the right side. See Figures
8 and 8b.
If needed, adjust the six Foot Assemblies (C).
8.