Whittier Wood 1262AFLSOa User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 12/13
Prairie City Panel Beds
AFLSO = Summer Oak finish
AFDAO = Autumn Oak finish
Assembly Instructions
Model #
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended to use this unit in a
commercial setting.
Remove items before you move this unit.
Do not overload the drawers.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
1262AFLSOa;
1262AFDAOa
Prairie City Cal-King
Panel Storage Bed
1279AFLSO;
1279AFDAO
Prairie City Cal-King
Panel Bed

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Parts List
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 2 —12/13
Please identify the parts and check that the quantities received match those on this list. If you need
to replace a part, refer to the model number, part letter and name.
1265AFLSO; 1265AFDAO
Cal-King Headboard/Footboard Kit (x1)
Part
Description
Quantity
A
Headboard Assembly
1
B
Footboard Assembly
1
U
#8 x 1" Black Screw (inserted)
16
ZN
#8 x 2" Black Screw (inserted)
4
ZO
Left Bed Bracket (attached)
2
ZP
Right Bed Bracket (attached)
2
Please note this Assembly Instruction is for Prairie City Cal-King Panel Storage Bed
(#1262) and Prairie City Cal-King Panel Rail Bed (#1279). The Parts Lists for each
component follow.

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Parts List
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 3 —12/13
1264AFLSOa; 1264AFDAOa Pedestal Kit (x2)
Part
Description
Quantity
Ea
Pedestal
1
F
Small Drawer Box (assembled)
2
Ga
Large Drawer Box (assembled)
1
H
Drawer Face (attached)
3
I
Cal-King Trestle (23-1/4")
2
J
Left/Right Center Deckboard
1
K
Notched Deckboard (attached)
1
L
Assembled Foot
3
M
Long Angle Iron (attached)
1
N
Drawer Slides (pre-installed sets)
3
O
#6 x 3/4" Philtruss Screw (inserted)
18
P
#6 x 3/4" Flat Head Screw (inserted)
10
Q
#6 x 1/2" Philtruss Screw
22
(18 inserted)
Ra
#8 x 7/8" Black Lo-Profile Screw (inserted)
18
S
#8 x 1-1/4" Black Screw
56
(48 inserted)
Ta
#8 x 1-1/2" Machine Screw Tuscan (installed)
6
U
#8 x 1" Black Screw (inserted)
9
V
Arched Washer (inserted)
4
W
1/4" Flat Washer
10
(4 inserted)
X
1/4" Lock Washer (inserted)
4
Y
1/4" x 20mm Insert Nut (inserted)
8
ZA
1/4" Hex Nut (inserted)
4
ZB
1/4" T-Nut (inserted)
2

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Parts List
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 4 —12/13
Part
Description
Quantity
ZC
1/4" x 80mm Hex Bolt
1
ZD
1/4" x 2-1/2" Hex Bolt (inserted)
4
ZE
1/4" x 1-3/4" Hex Bolt
6
ZF
Pull (attached)
3
ZG
#8 x 20mm Pan Head Screw (inserted)
12
ZH
Foot Bracket (attached)
3
ZI
Adjustable Glide (installed)
3
ZJ
Left Pedestal Angle Bracket (inserted)
1
ZK
Right Pedestal Angle Bracket (inserted)
1
ZL
90oBracket
1
ZM
Hex Wrench
1

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Parts List
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 5 —12/13
1283AFLSO; 1283AFDAO Cal-King Rail Kit (x1)
Part
Description
Quantity
S
#8 x 1-1/4" Black Screw
10
U
#8 x 1" Black Screw (inserted)
16
ZB
1/4" T-Nut (inserted)
9
ZC
1/4" x 80mm Hex Bolt
2
ZM
Hex Wrench
1
ZN
#8 x 2" Black Screw (inserted)
22
ZO
Left Bed Bracket (attached)
2
ZP
Right Bed Bracket (attached)
2
ZQ
Side Rail
2
ZR
Slat
5
ZS
Slat Support
2
ZT
Assembled Foot
4
ZU
Adjustable Glide with Hex Nut (installed)
4
ZV
#8 x 1-5/8" Black Screw
4
ZW
5/16" x 3/4" Insert Nut (inserted)
4
ZX
1/4" x 45mm Hanger Bolt (inserted)
4

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Assembly Instructions
This assembly requires two people.
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 6 —12/13
Tools Required: 4mm Hex Wrench (provided), Phillips screwdriver, Slotted screwdriver, 1/2" &
7/16" open end or box end wrench and Tape measure
Notes:
Steps 1 through 10 are for the Prairie City Cal-King Panel Storage Bed (#1262).
Steps 11 through 18 are for the Prairie City Cal-King Panel Bed (#1279).
1. Place both Pedestals (Ea) approximately 74" apart as shown in Figure 1.
2. To attach the Footboard (B) to the Pedestal (Ea), align the Brackets and slide the Pedestal
down on to the Footboard (B). See Figures 2 and 2a.
Fig. 2
Ea
B
Fig. 2a
Fig. 1
74"
Ea

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Assembly Instructions
This assembly requires two people.
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 7 —12/13
3. Repeat step two for the other side. See Figures 3 and 3a.
4. Align the Brackets on both sides and slide the Pedestal/Footboard assembly down on to the
Headboard (A). See Figure 4.
Fig. 3
Ea
Fig. 3a
Fig. 4
A

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Assembly Instructions
This assembly requires two people.
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 8 —12/13
5. NOTE: There are blocks mounted on the back side of the Footboard to support the end of
the pedestal eliminating the need for an Assembled Foot in this position where it would
be easily visible. Do not attach an Assembled Foot in the position near the footboard.
Align three Assembled Feet (L) over the insert nuts that are on the back of the Pedestal. Make
sure the Adjustable Glides are on the outside face of the Pedestal. See Figures 5 and 5a. Attach
to the Pedestal with 1/4" x 1-3/4" Hex Bolts (ZE) and 1/4" Flat Washers (W).
Fig. 5
Fig. 5a
L
ZE
W
ZE
W
W
ZE
x 6
x 6

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Assembly Instructions
This assembly requires two people.
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 9 —12/13
6. Repeat by attaching three additional Assembled Feet (L) to the other Pedestal with 1/4" x 1-3/4"
Hex Bolts (ZE) and 1/4" Flat Washers (W). See Figures 6 and 6a. Using a 1/2" wrench or
Slotted screwdriver adjust the Adjustable Glides (ZI) on the bottoms of the Assembled Feet (L)
so that the top surfaces of both Pedestal decks are 16" from the floor.
Fig. 6
Fig. 6a
ZE
W
W
ZE
x 6
x 6
Pedestal
Deck

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Assembly Instructions
This assembly requires two people.
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 10 —12/13
7. Facing the Footboard, attach the Pedestal Assembly to the Footboard with a 90º Bracket (ZL)
and four #6 x 1/2" Philtruss Screws (Q). Repeat for the other side. See Figures 7 and 7a.
Using the Hex Wrench (ZM), attach the Headboard to the Pedestals with two 1/4" x 80mm Hex
Bolts (ZC). See Figure 7.
Fig. 7
Fig. 7a
ZL
Q
ZL
Q
x 2
x 8
ZC
x 2
ZM
x 1
ZC
ZC

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Assembly Instructions
This assembly requires two people.
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 11 —12/13
8. Move the bed assembly to its final position; if necessary readjust the glides at the bottom of the
Assembled Feet so that all are touching the floor and support weight. Place the four Cal-King
Trestles (I) into the bed assembly as shown in Figures 8 and 8a.
IMPORTANT: the center two trestles nest into the notches at the top of the Assembled
Feet, the trestles at each end must nest into the notches in the cleats which are attached
closer to the ends of the Pedestals.
Fig. 8
Fig. 8a
I
I
I

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Assembly Instructions
This assembly requires two people.
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 12 —12/13
9. To make sure the bed is square, measure the distance between opposing corners. If one of the
measurements is larger, tap on a footboard leg until the measurement is equal. See Figure 9.
10. Place the Left/Right Center Deckboards (J) as shown in Figure 10 and secure with
eight #8x1-1/4" Black Screws (S). There should be a small gap between each deckboard.
This concludes the assembly process for Prairie City Storage Bed, if
you have purchased a Prairie City Rail Bed please refer to the
instructions beginning on page 13.
Fig. 10
S
S
x 8
J
Fig. 9

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Assembly Instructions
This assembly requires two people.
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 13 —12/13
11. Position the two Slat Support (ZS) over the blocks that are mounted onto back side of the
Footboard (B) and attach with four #8 x 1-5/8" Black Screws (ZV) through the predrilled holes in
the slat supports and into the location punches on the blocks. See Figure 11.
12. To attach the Footboard (B) to the Side Rail (ZQ), align the Brackets and slide the Side Rail
down on to the Footboard (B). See Figures 12 and 12a.
Fig. 12
ZQ
B
Fig. 12a
Fig. 11
ZS
B
ZS
ZV
x 4
ZV
Pre-attached blocks

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Assembly Instructions
This assembly requires two people.
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 14 —12/13
13. Repeat step twelve for the other side. See Figures 13 and 13a.
14. Align the Brackets on both sides and slide the Side Rail/Footboard assembly down on to the
Headboard (A). See Figure 14.
Fig. 13
ZQ
Fig. 13a
Fig. 14
A

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Assembly Instructions
This assembly requires two people.
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 15 —12/13
15. Using the Hex Wrench (ZM), attach the Headboard to the Side Rails with two 1/4" x 80mm Hex
Bolts (ZC). See Figure 15.
16. Attach an Assembled Foot (ZT) to four of the five Slats (ZR) as shown in Figure 16.
Fig. 15
ZC
ZC
x 2
ZM
x 1
ZR
Fig. 16
X 4
ZT

1262AFLSOa; 1262AFDAOa Prairie City Cal-King Panel Storage Bed;
1279AFLSO; 1279AFDAO Prairie City Cal-King Panel Bed
Assembly Instructions
This assembly requires two people.
1262AFLSOa_1262AFDAOa_1279AFLSO_1279AFDAO —Page 16 —12/13
17. Move the bed assembly to its final position. Position the Slats (ZR) on the bottom edges of the
rails and place the slat without the Assembled Foot nearest to the Footboard. Attach with
#8 x 1-1/4" Black Screws (S). See Figure 17.
18. Adjust the Adjustable Glides with Hex Nut (ZU) on the Assembled Feet (ZT) so the Glides just
touch the floor, making sure the Assembled Feet bear weight.
S
x 10
Fig. 17
S
Slat without
an
Assembled
Foot.
ZR
ZU
Fig. 18
ZT