Whittier Wood 1416AFVCL User manual

P.O. Box 2827
Eugene, OR 97402 USA
Outside U.S. or Canada: 541- 687- 0213Outside U.S. or Canada: 541- 687- 0213
800-653-3336800-653-3336
Fax: [phone] • Fax: [phone] • wwwwww.whittie.whittierrwood.comwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.AMail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A
For normal household use only.
recommended for commercial use.
Congratulations!
Production Code:
Shaker
Queen Storage Bed
1416AFVCL
VN
Service Policy: We will replace parts
which are defective, missing or damaged.
Please contact Whittier Wood Products
customer service department directly (by
phone, fax, mail or E-mail) for replacement
parts.
Hours: Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order: Provide the complete furniture
model number, part letter, production code,
quantity needed, reason for replacement
and your full name and address along with
a telephone number in case we need to
contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
This fine piece of furniture will make a handsome
addition to your home. For the best results, start
by reading the Finishing Hints before you begin
your project.
Unload items from this unit prior to moving.
Before loading or moving this unit, check all screws
and supports for tightness.
Store the item: 1) in the box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may be
affecting the stability of your furniture. Tighten or repair
as needed.
This Assembly requires two people.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
Rev. 01/08
(Candlelite Finish)
Assembly Instructions

If you should need to replace a part please refer to the following list for part number.
F — 1/4" x 3" Hex Bolt
— Qty. 12
G — 1/4" x 1-½" Hex Bolt
— Qty. 8
E — #8 x 1" Black Screw — Qty. 24
H — Washer — Qty. 20
N — #8 x 1½" Machine Screw
— Qty. 6 O — Knob — Qty. 6
I — Pedestal Kit — Qty.1
A — Headboard — Qty.1
B — Footboard — Qty.1
C — Trestle — Qty.4
D — Insert Nuts — Qty.12
(Pre-Inserted)
Q — Drawer Slides — Qty.12
(Pre-Installed)
J — Drawer Box Small — Qty.4
K — Drawer Box Large — Qty.2
L — Drawer Face Small — Qty.4
P— Deckboard — Qty.1
M — Drawer Face Large — Qty.2
Shaker Queen Storage Bed AFVCL — Parts List
1419AFVCL (x1)
1418AFVCL (x2)
Page 2 — 1416AFVCL (01/08)

Shaker Queen Storage Bed
Assembly Instructions
Page 3 — 1416AFVCL (01/08)
TOOLS REQUIRED:
This Assembly Requires Two People
Phillips screwdriver, 7/16" open end or box end wrench and tape measure.
Remove the Trestles from the back of the Headboard as seen in Fig. 1
and place them off to the side.
1.
Place both Pedestals (I) approximately 63" apart as shown in Fig.2.2.
Fig. 1
Fig. 2
Shipping Straps
I
I
63"

Page 4 — 1416AFVCL (01/08)
Remove all Drawers from both Pedestals. The drawers have been pre-aligned
from the factory. Take note of where each drawer came from to insure easy
re-installation. The drawers are marked on the back end to assist in this process.
3.
Place 4 Trestles (C) in between Pedestals and insert 1-1/4" Hex Bolt (G) and
washer (H) as shown in Fig. 4b. Finger tighten only.
4.
Fig. 4b
G x 8 H x 8
F x 6 H x 6
CCCC
H
G
F
H
Fig. 4
Assemble the Footboard (B) to the Pedestal Assembly as shown in Fig. 5. using
1/4" x 3" Hex Bolt (F) and Washer (H).
5.
Fig. 5
B

Page 5 — 1416AFVCL (01/08)
Repeat step 5 to assemble the Headboard (A) to the Pedestal Assembly as shown
in Fig. 6.
6.
Tighten all bolts on Trestles securely.7.
Place Deck Boards (P) as shown in Fig. 7 and secure with #8 x 1"Screw (E). 8.
Re-install Drawers into their original positions. Sleep Soundly.
9.
Fig.6
Fig. 7
E x 24
A
P
F x 6 H x 6