Wi-Tek WI-PCMS310GF User manual

WI-PCMS310GF QSG Page 1 of 10
Cloud Managed, 802.3at PoE Switch
Quick Start Guide
WI-PCMS310GF
8GE + 2 SFP
Layer 2 Cloud Managed 802.3at PoE Switch Quick Start Guide
V2212

WI-PCMS310GF QSG Page 2 of 10
Table of Contents
1. Introduction .................................................................................................................................3
2. Package Contents ...................................................................................................................... 3
3. System Requirements ................................................................................................................ 3
4. LEDs ...........................................................................................................................................4
4.1 System LEDs ........................................................................................................................................................................... 4
4.2 RJ45 LEDs ............................................................................................................................................................................... 4
4.3 SFP LEDs ................................................................................................................................................................................ 4
5. Front Panel ................................................................................................................................. 5
6. Configuration .............................................................................................................................. 5
6.1 Accessing the Configuration Interface ..................................................................................................................................... 5
6.1.1. Graphical User Interface (WebGUI) ......................................................................................................................................................... 6
6.1.2. Command Line Interface (CLI) .................................................................................................................................................................6
6.1.3. Cloud Management Server ...................................................................................................................................................................... 6
6.1.4. SNMP Manager ....................................................................................................................................................................................... 6
6.2 SNMP and MIBs .......................................................................................................................................................................8
7. Firmware Update ........................................................................................................................ 9
7.1 Update using GUI .....................................................................................................................................................................9
7.2 Update using TFTP ................................................................................................................................................................ 10

WI-PCMS310GF QSG Page 3 of 10
1. Introduction
The WI-PCMS310GF is a Managed, Layer 2 (L2), POE 802.3at (48V/30W per port) IP Switch, with Gigabit Ethernet
(GbE), Small Form-factor Pluggable (SFP), and serial Console interfaces.
This document supplements the Quick Installation Guide available for download from:
https://ubwh.com.au/documents/PCMS310GF/QIG.pdf
2. Package Contents
WI-PCMS310GF
Quick Start Guide 19” Rack Kit
Console Cable Power Cord
3. System Requirements
Web Browser: e.g. Mozilla Firefox, Google Chrome, Safari, Microsoft Edge, or Microsoft Internet Explorer.

WI-PCMS310GF QSG Page 4 of 10
4. LEDs
4.1 System LEDs
LED
State
Status
SYS Blinking
(slow)
Normal Operation
PWR On Steady on if power applied
4.2 RJ45 LEDs
LED
State
Status
PoE Off No Power applied
Orange 48 V PoE applied
Link Green 10/100/1000 Mbps connection.
Flashes with activity.
Off No Ethernet connection
4.3 SFP LEDs
LED
State
Status
9
10
Off No link
Green Link established at 1000 Mbps (1 Gbps)
Flashing Indicates Activity

WI-PCMS310GF QSG Page 5 of 10
5. Front Panel
Port
Description
Note Active PoE means a device is connected, and PoE voltage is applied.
RJ45 1-8 LAN: 10/100/1000 Mbps Ethernet connection
PoE Out. 2-Pair,
Pins: 48V= 1,2(-) 3,6 (+) (Ports 1-4)
1,2(+) 3,6 (-) (Ports 5-8)
Software selectable:
Off
48 V Active 803.3at 32 W max
48V Forced On
SFP 9-10 Hot-swappable Small Form-factor Pluggable (SFP) ports supporting 1 Gbps connections.
Console This port is compatible with Cisco part number 72-3383-01 (Console Cable). The serial settings are:
Baud rate: 9600
Data bits: 8
Stop bits: 1
Parity: None
Flow control: None
RESET Button to the left of the PWR LED.
To reset the Switch to factory defaults:
The Switch should be running after bootup is complete and the SYS LED is blinking.
Press and hold the Reset button until the SYS LED starts flashing rapidly.
Release the Reset button.
6. Configuration
This section covers some tasks that are not fully covered in the Quick Installation Guide (see section Introduction,
page 3).
6.1 Accessing the Configuration Interface
There are numerous configuration options:
1. Graphical User Interface (GUI), using an Ethernet connection.
2. Command Line Interface (CLI),
using a console cable, or SSH1terminal
3. Cloud Management server.
4. SNMP Manager
1https://en.wikipedia.org/wiki/Secure_Shell

WI-PCMS310GF QSG Page 6 of 10
6.1.1. Graphical User Interface (WebGUI)
When in Factory Reset state, the Switch is set to use DHCP to acquire an IP address from the local DHCP server.
If there is no DHCP server, the default IP address is 192.168.0.1.
Please consult this manual:
https://ubwh.com.au/documents/Wi-
Tek%20Cloud%20Managed%20Switches%20WEB%20User%20Manual.pdf
6.1.2. Command Line Interface (CLI)
Please consult this manual:
https://ubwh.com.au/documents/Wi-
Tek%20Cloud%20Managed%20Switches%20CLI_User%20Manual.pdf
6.1.3. Cloud Management Server
Please consult this document:
https://ubwh.com.au/documents/Wi-
Tek%20Cloud%20Getting%20Started%20Guide%20-%20Switches.pdf
6.1.4. SNMP Manager
There are many Network Management software platforms that can be used to monitor & control SNMP enabled
devices.
Shown below is an example of using the free, open-source HomeAssistant2platform to monitor & control a
PCMS310GF.
Figure 1 - Home Assistant Dashboard
2https://www.home-assistant.io/

WI-PCMS310GF QSG Page 7 of 10
Figure 2 - HomeAssistant logs values over time. Shown here is Port 2 PoE power
To learn how to integrate one of these switches into HomeAssistant, see:
https://ubwh.com.au/WI-PMCS310GF
And scroll down to the Home Assistant (HA) Managed section.

WI-PCMS310GF QSG Page 8 of 10
6.2 SNMP and MIBs
The Switch supports the Simple Network Management Protocol (SNMP: V2c and V3). The Management Information
Base (MIB) definition files are available from:
https://ubwh.com.au/documents/WiTek-MIBs.zip
Shown below are some example screen captures from a Windows program called PowerSNMP Free Manager
available from https://www.dart.com/pages/powersnmp-free-manager
Figure 3 - Basic SNMP queries
Figure 4 PoE Table Query

WI-PCMS310GF QSG Page 9 of 10
7. Firmware Update
Firmware updates are available from:
https://www.wireless-tek.com/search.php?type=2
See the Firmware section
If there is no firmware there for your product, that means there have been no firmware updates.
7.1 Update using GUI
1. Open the WebGUI and navigate to
2. Choose
a. Action = Upgrade
b. Method = HTTP
3. Choose the *.bix file containing the new firmware
4. Click Apply
5. Wait until you see
Click OK
6. This page should appear.
Click Apply
7. Click Reboot (top-right corner)

WI-PCMS310GF QSG Page 10 of 10
7.2 Update using TFTP
1. Open the WebGUI and navigate to
2. Choose
a. Action = Upgrade
a. Method = TFTP
3. Install the *.bix file on a TFTP server
4. Enter the TFTP server network address & the file name
8. Click Apply .