Wicksteed PICUS Series User manual

PAGE OF1 3
Wicksteed Leisure Ltd, Digby Street, Kettering, Northants NN16 8YJ Tel: [phone] Fax: [phone]
www.wicksteed.co.uk E:[email protected]o.uk
No part of this document may be copied or used without the express written permission of WICKSTEED LEISURE LTD (c) 2013
FFH
SIZE
AGE RANGE
PROD. CODE
TECHNICAL DATA
MINIMUM SPACE REQUIRED
SUPERVISED PLAY
EQUIPMENT TYPE
LARGEST PART
RECOMMENDED
HEAVIEST PART
INSTALLATION DETAILS
1. READ INSTALLATION INSTRUCTIONS THROUGHLY BEFORE COMMENCING INSTALLTION OF UNIT
2. EXCAVATE FOUNDATIONS USING THE DETAIL AS SHOWN ON PAGE 2 OF THIS DOCUMENT
3. ENSURE TO CHECK AND TIGHTEN ALL FIXINGS USING PROTECTIVE CAPS WHERE NECESSARY
4. BACKFILL FOUNDATIONS WITH CUBIC M CONCRETE ALLOWING TO SET FOR 48 HOURS
5. REMOVE ALL ASSEMBLY AIDS BEFORE THE EQUIPMENT IS USED
THIS PRODUCT CONFORMS WITH BS EN1176- :2008
Version:
Date:
PICUS
PICK UP STICKS 3 SS SLIDE
PICUS3SS
L: 3.41M W: 5.12M H: 1.7M
0.9M
4-7 YEARS OLD
6.2M X 7.9M
LOW LEVEL
STEEL SLIDE 1.97M X 0.4M X 0.85M
18.5KG
0.062
1
A
10/04/13
BS EN1176- 3:2008

PAGE OF2 3
750.0
748.0
748.0
820.0775.0576.51195.0
1057.0 705.0
FOUNDATIONS 350MM X 350MM X 600MM DEEP UNLESS OTHERWISE SPECIFIED
1845.0
245.0
1038.5854.01473.0
916.5 301.5
799.0344.0 151.0
648.0
900 X 300 X 250 DEEP

PAGE OF3 3
30.8 SQ METRES WETPOUR SURFACING
21.6 LINEAR METRES WETPOUR EDGING
7103.0
6193.0
946.6
2414.02098.6
3101.8
1532.5
1532.5
2768.3
1605.2
1306.3
1185.1
926.3
1537.3
1489.7
8000.0
7000.0
29 GRASS SAVER TILES (1.5M X 1.0M)
1883.0
1500.0
1619.4
2077.4

PAGE OF1 8
Wicksteed Leisure Limited, Digby Street, Kettering, Northamptonshire NN16 8YJ Tel: [phone] Fax: [phone] http://www.wicksteed.co.uk Email:[e-mail]
No part of this document may be copied or used without the express written permission of WICKSTEED LEISURE LIMITED (c) 2013
3rd Angle
Projection
Date:
Drawn By:
Drawing Number:
Sheet:
Issue Date:
Sign:
Issue:Code:
Low Level
Pick Up Sticks Three SS Slide Installation/Assembly
PICUS
PICUS3SS
PICUS3SS-IN-AY
AK
OF
18
11/04/13
A
11/04/13
AK
Parts List
ITEM QTY PART NUMBER DESCRIPTION
1 1 Tri deck TRIANGLE DECK
2 1 FRTB00664 PICUS3 TIMBER SET
3 1 FRPE00795 PICUS3 SS HDPE PANEL
41 FRMS00665 PICUS3 ROPE SET
5 1 FRMT01023 GROUND ANCHOR SCRAMBLE NET
6 4 M10X40BHSS M10 x 40 Socket Button Head SS
72 SS ANCHOR SLIDE GROUND ANCHOR
8 1 FRMT00796 900 SS SLIDE
9 4 SSB505090R 50 X 50 X 125 DIA POST BRKT
10 4M10X35BH M10 x 35 Soc Button MS ZP
11 7 M10X70CS M10 X 70 COACH SCREW
12 2 M10X80BHSS M10 x 80 Socket Button Head SS
Parts List
ITEM QTY PART NUMBER DESCRIPTION
13 9 M10X120CS M10 X 120 COACH SCREW
14 5 M12X150CS M12 X 150 COACH SCREW
15 1 M12X200CB M12 x 200 Coach Bolt
16 8 M12X220CB M12 x 220 Coach Bolt
17 2 M12X230CB M12 x 230 Coach Bolt
18 27 M10SWASH M10 PLAIN WASHER
19 10 M10NYLOC M10 NYLOC HEX NUT MS ZP
20 35 M12WASH 1/2" X 1 1/4" 12G WASHER
21 21 M12NYLOC M12 NYLOC NUT
22 35 PLC480DCAP GREEN POLY CAP 48
23 17 M10DONUT M10 DONUT (GREEN)
POST LABELS
(REFER TO TIMBER DRAWING FRTB00664)
A
B
F
F
F
I
J
K
L
M
G
EH
D
C
N
O
N
N
O
EQUIPMENT NEEDED
n 13 AUGER DRILL BIT
n 8 DRILL BIT
B

PAGE OF2 8
DETAIL A
BUILD TRIANGLE PLATFORM WITH SLIDE
Excavate the foundations as detailed using sheet PICUS3-SPEC. Using posts labelled 'O' loosely secure to the upright posts labelled 'N' using the supplied
Washer Screws to the dimensions detailed below. Pay strict attention to the direction of the counterbore holes on posts 'N' as these will have to be facing the
correct direction for the rope attachment detailed later on in this installation guide. NOTE: Do not fully tighten the Washer Screws until the unit has been
assembled.
SURFACE LEVEL
814.5
900.0
NN
N
O O
SLIDE
DETAIL B
11 18 23
The counterbore holes will point in the direction of an opposite post/
foundation as illustrated with the arrows in Detail View A. The counterbore
will be on the opposite side to the arrow head.
With the three posts formed secure the triangle deck frame to the three
upright posts using the supplied Coach Screws as shown in Detail View B.
Once the frame has been established, the decking can be laid on top and
secured using the supplied assy screws.
810.5
755.0
SECURE USING SUPPLIED
M8 X 140 WASHER SCREWS

PAGE OF3 8
C
Secure the HDPE slide frame to the front of the deck and the upright posts as illustrated in Detail View C. Ensure there are no gaps between the posts and
the HDPE slide frame, any gaps can be eliminated by maneuvering the posts labelled 'O' and the triangle deck.
DETAIL C
With the HDPE slide frame secured attach the stainless steel slide using the supplied Button
Head Screws. A drill hole may have to be created to go through the timber deck so the
steel slide can attach securely to the HDPE panel and the Triangle Timber Deck.
With the deck assembly complete and the correct shape achieved, concrete can
now be added to the four foundation holes for this part of the unit.
11 18 23
10 18 19 23
9
12181923
618
181923
8

PAGE OF4 8
POST ASSEMBLY & INSTALLATION
The Upright posts on this unit should all be leaning at a 10 ~ angle away from the deck structure. The posts should all be drilled and of the correct size to
achieve this angle. Ensure all bolts and screws are loosely fitted to give enough movement for ropes and timbers to have the appropriate tensioning.
Sustain the two upright posts labelled 'I' & 'J' into the corresponding foundation hole. Both Posts have pre-drilled holes to secure the horizontal posts to using
the supplied Coach Bolts. Secure post labelled 'A' to the lower hole on post 'I' and fix using the supplied Coach Bolt. The upper end of post 'A' is fixed to post
'N' on the triangle deck using a Coach Screw to the dimension shown below. Repeat this same process for post labelled 'B' but with the second hole from
ground level on post 'J'.
A
B
I
F
J
SURFACE LEVEL
With Posts 'A' & 'B' bracing the upright posts, secure post 'F' to the pre-drilled holes using the supplied
Coach Screws. NOTE: The Dimensions for the pre-drilled holes below are mearly a reference to using
the correct hole on the upright post. If made to the correct these posts shouldn't require drilling.
SECURE USING
M12 X 150 COACH SCREWS
SECURE USING
M12 X 220 COACH BOLTS
693.0
687.5
436.0
285.0
320.0
223.0

PAGE OF5 8
Prop post labelled 'K' into the foundation hole. Loosely secure post 'G' to posts 'J' & 'K' using the supplied Coach Screws. Ensure the horizontal log is sat on
the deck side of the two upright posts. Attach post 'B' to the pre-driled hole under post 'G' onto post 'K' The other side of post 'B' is secured to the triangle
deck post using a Coach Screw (as positioned below).
G
B
K
NOTE: The Dimensions for the pre-drilled holes below are mearly a reference to using the correct
hole on the upright post. If made to the correct these posts shouldn't require drilling.
SECURE USING
M12 X 230 COACH BOLTS
SECURE USING
M12 X 220 COACH BOLT
SECURE USING
M12 X 150 COACH SCREW
600.0
435.0
521.0

PAGE OF6 8
Prop posts labelled 'L' & 'M' into the foundation hole. Loosely secure post 'C' & 'D' to posts 'L' & 'M' using the supplied Coach Bolts. Attach the other ends
of posts 'C' & 'D' to the tirangle deck frame with the supplied Coach Screws as illustrated.
L
M
C
D
L
M
NOTE: The Dimensions for the pre-drilled holes below are mearly a reference to using
the correct hole on the upright post. If made to the correct these posts shouldn't require drilling.
SECURE USING
M12 X 220 COACH BOLTS
SECURE USING
M12 X 150 COACH SCREWS
640.0
585.0
343.0
290.0

PAGE OF7 8
Secure the end of post labelled 'E' to the pre-drilled hole in upright post 'M' using the supplied Coach Bolt. This should give post 'E' the correct angle to sit
on already connected posts and secure with 2 x Coach Screws. Add the additional logs 'F' & 'H' to the structure securing with M10 X 120 Coach Screws.
NOTE: Post 'H' Sits on the underside of an existing log and is secured with an M12 x 200 Coach Bolt. The hole for this Coach Bolt will need to be positioned
and drilled prior to being able to attach post 'H'.
E
F
H
M
DRILL & COACH BOLT
POST TO UNDERSIDE
H
E
F
Use the illustrated dimensions as a reference to locate the timber horizontals
in the correct place.
SECURE USING
M12 X 220 COACH BOLT
400.0
625.0
455.0
685.0
275.0

PAGE OF8 8
Secure the remaining posts to the unit to the dimensions given below using
the supplied M10 x 120 Coach Screws. Dimensions are measured along the
width of the timber horizontal.
ATTACH THE ROPES
Finally, with the structure complete the ropes can be
secured to the correct upright posts. With the unit
loosely connected the posts should be able to lean
to the desired angle and to achieve tension in the ropes.
Once the ropes have been secured, the fixings can be
tightened and concrete can be added to the foundations.
Leave concrete to set for 48 Hours.
F
F
575.0
900.0
490.0
240.0