Wiedamark IRDIP-11091A6-00D-11 User manual

IRDIP-11091A6-00D-11 User Manual
Please read the manual carefully before use and keep it for future use.
Notice
Corrosive or soluble chemicals will do harm to the housing.
Working temperature is not above 40℃，and humidity is between 0~95％
Indoor Use
Warning
zBe sure that the running voltage is the same as the rating voltage on the fixture
zConnect the fixture to the earth linked power supply
zPlease contact the professional engineers for repair.
Specification
1.Voltage: AC120V 60HZ/240V 50HZ
2. Power Consumption: 14W
3.Fuse：1A 250V/2A 125V
4.Light Source :￠10 LED Red 37 PCS, Green 36 PCS, Blue 36 PCS
5.Function :DMX, Auto, Sound, Manual, Master-Slave
Page 1 of 4

6.DMX Channels：5
7.Dimension：L230XW160XH213mm
8.Net Weight：2.1 KG
Packing Details
1. IRDIP-11091A6-00D-11￠10 LED Bar Light--------------------------------------------------------- 1PC
2. User Manual ------------------------------------------------------------------------------------------------ 1PC
Operation Instruction
zItem Description
IRDIP-11091A6-00D-11 consists of 109 PCS ￠10 RGB LEDs in total, 37 PCS red LEDs,36 PCS
green LEDs and 36 PCS blue LEDs. It has five working modes, including DMX, auto, sound, manual and
master-slave. It enjoys vivid effect, such as color change, dimmer, strobe and fade. It is user friendly as
well. The above advantages make it suitable for all kinds of entertainment occasions and home party.
zPanel Instruction
1. Display
2. UP Button
3. DOWN Button
4. MENU Button
5. Mic-set
6. Sensitivity
7. Power Connector
8. Male DMX Connector
9. Female DMX Connector
zInstallation Instruction
The fixture can be laid on the ground or hung for use. Please lock the hand wheels and screw well so as
to avoid danger.
Page 2 of 4

zFunction Instruction
1. Reset after it is connected to power supply
After powered on, the system goes to initialization, the LED display shows the previous working mode. For
example, the DMX address is 1 previously. Then after powered on, it shows A001 as below.
DMX Working Mode
1. DMX Mode and Address Setting
Press MENU button until the display shows DMX working mode. Then undo the MENU button to
enter DMX modes. Choose UP or DOWN button to modify the address between 001 to 512. Press Menu
and back to the current working mode.
DMX mode
A
dd 001
DMXmode
Add 001
*Reset*
2. DMX Pin Assignment：
Male and Female DMX connector Pin Assignment:Pin1 = Gnd Pin2 = Dmx- Pin3 = Dmx+
3. DMX CONNETION CHART
First Second …… n
4. DMX Function Chart
CH1 CH2 CH3 CH4 CH5
0~50 Black Out NA NA NA NA
51~100 Dimmer1 Flash All Red All Green All Blue
Page 3 of 4

101~150 choose Flash Color choose NA NA
151~200 Color change Speed Color change NA NA
201~255 Color fade Speed fade NA NA
DMX Connection Test：Use Three-Pin Connection cable to connect the each unit.Set up the same DMX
address and the units can work in synchronization.
Master Slave Mode
（I）Auto Mode
Press MENU button until the display shows AUTO Mode and then undo the MENU button to enter Auto
Mode. Press menu button to choose different parameter interface, which is as the below chart shows.
Press UP or DOWN button to modify the corresponding parameter. Keep pressing these two buttons, you
can speed up or slow down.
Parameter Instruction
Spd XX(01~10): Choose running speed of the pre-set programs, ten different speed to choose. 01
refers to the quickest and 10 refer to the slowest..
Fad XX(01~10): Choose to run FADE effect in pre-set program. Ten in total. 01 refers to the quickest
and 10 refers to the slowest
（II）Sound Mode：
Press MENU button until the display shows SOUND Mode and then undo the MENU button to enter
SOUND Mode. Press UP or DOWN button to modify the corresponding parameter.
Aut mode
Spd XX Aut mode Fad XX
Aud mode
Fad XX
Parameter Instruction
Fad XX(00~10): Choose to run FADE effect in pre-set program. Five in total. 01 refer to the quickest
and 05 refer to the slowest。
Slave mode：The fixture can work in auto or sound mode in Master
zTrouble-shooting
Trouble Reason Trouble Shooting
The fixture doesn’t
work
1.Check if the fixture is running under
rating voltage
2.Check if the fuse is burnt
1. Be sure that the fixture is running
under rating voltage
2.Change fuse with the same
specification
LED is dim 1. Check if the fixture is running
under rating voltage 1. Be sure that the fixture is running under rating voltage
Sound Mode
doesn’t work
1.Check if the fixture is working in
sound mode
2.Check the sound sensitivity
1.Set up the sound mode
2.Increase the sensitivity
The fixture can not
receive the DMX
signal
1．Check if the DMX cables are
connected rightly
2．Check if the fixture is working in
DMX mode
1．Be sure that the DMX cables are
connected rightly
2．Set up DMX mode
Page 4 of 4