Wiedamark MK-L150W User manual

ISO9001:2000
CERTIFIED
MENU
UP
DOWN
MIC
LIGHT ENGINE
USER MANUAL
Accessories:
Fiber Connector .............................. PC1
Wireless Remote Controller...............1 PC (Optional)
User Manual .............................. . . . . . . 1 PC
Signal Cable ....................................1 PC (for DMX machine only)
MK-L150W
MK-L150W DMX
M O D E L :

Fig.1
1. Technical Data
2. Installation dimension of light engine (see Fig.1):
Model: LEI-8001 Model: LEI-15001
Voltage: 110V 230V
Power: 90W Power: 150W
Color Wheel: 6 colors
LED: White
Light Source: 1-70W LED Light Source: 1-130W LED
Luminous Flux: 6100Lm(6000K) 11000Lm(6000K) Luminous Flux:
Life of LED : 50000H
Standard Aperture: Ø28mm / Ø24mm / Ø20mm (Optional: Ø30mm Max)
3
Size: 291X264X135mm
Gross Weight: 7.0Kg
3. Light Engine Setup:
(1) DIP switches: SW1~SW3 for programs selection, please see
Attached Table (1=ON, 0=OFF). SW4 and SW5 are blank;
SW6 for remote control (see fig. 2)
ON OFF
1
2
4
8
16
DIP
1 2 3 4 5 6
R
Fig. 2
1
Safety Instruction
1. Make sure the Light Engine and Power Source have the same voltage;
2. Keep out of rain or moist area to avoid shock hazards;
3. Avoid to work in high ambient temperature ( >40°C);
LIGHT ENGINE
USER MANUAL
2
(4) Fixing Color With Wireless Remote Controller : Firstly set SW2 and SW3 as “ ON ” to
choose the inbuilt programme, P06, of which the colors change at a slow speed, then
press the button “ ” on the controller to fix the color when the light engine displays
the color that you need.
Notice:
1.You could only control the motor to be on and off through “ ” button.
If you want to have different color-change speed, please use DIP switch.
PRO. NO. DIP SWITCH(1=ON, 0=OFF)
1 2 3 4 5 6 FUNCTION
W, Sky-B,G,Y, B, PP, fade ( 6RPM)
Motor stopped, LED working
W, Sky-B,G,Y, B, PP, fade ( 4RPM)
W, Sky-B,G,Y, B, PP, fade ( 3RPM)
W, Sky-B,G,Y, B, PP, fade ( 2RPM)
W, Sky-B,G,Y, B, PP, fade ( 1.5RPM)
W, Sky-B,G,Y, B, PP, fade ( 1RPM)
W, Sky-B,G,Y, B, PP, fade ( 0.5RPM)
Attached Table:
Notice: 1. RPM is the speed of the color wheel;
2. If DIP address is set beyond P07, the machine will run P07 instead.
2. The dimmer on the rear panel is used for brightness manual adjustment.
The factory default is 100% brightness, and there are 6 levels of brightness
in total.
Wireless Remote Controller
Power ON/OFF
Color Fixing
Brightness Adjusting
Fig. 3
(2) Calculation of DIP address code:
e.g. 003=2(2)+1(1)，005=4(3)+1(1)
Set SW6 as “ON”, and the remote controller starts to work. Button “ ” is applied
to fix color, button “ ” for power on/off, and button “ ” “ ” used for brightness
adjusting. (6 levels) (See Fig. 3)
(3) Wireless Remote Controller:
RC-04
0 0 0 0 0 0
1 0 0 0 0 1
0 1 0 0 0 1
1 1 0 0 0 1
0 0 1 0 0 1
1 0 1 0 0 1
0 1 1 0 0 1
1 1 1 0 0 1
0 0
0 1
0 2
0 3
0 4
0 5
0 6
0 7
11 0
LED LIGHT
SERIES
275
291
26 4
135
FUSEPOWER
SWITCH
AERI AL
LED DI M DIP
DIP
DIM
Fixing Flange
Fuse
Power switch
Power cable
Aerial (optional)
Fan
Welcome to use MK series of professional light engine. Please
read the manual carefully before turning on the light engine. If you have any
questions concerning the operation or maintenance, please contact your
wholesaler.
CHAPTER 1 MK-L150W
ENGINE
MK
MK-L150W

3
135
11 0
LED LIGHT
SERIES
MENU
UP DOWN
MIC
AERI AL
275
291
264
Fixing Flange
Menu(UP,DOWN)
Fan
2. Installation dimension of light engine(see Fig1):
(1) DMX 512 signal control mode:
a. Address Code Setup:
Press button “UP” and “DOWN” at the same time (maybe several times) until the digital
display shows “ ”, then press the button “UP” or “DOWN” to select the address
code.
b. DMX Channels: 5 Channels
CH1:Color CH2:Speed CH3:Blank CH4:Dimmer (256 level) CH5:Strobe
Notice: CH2 controls the switching speed of colors in CH1.
CH3 is the spare channel.
001-508
1. Technical Data
Voltage: 110V 230V
Power: 90W Power: 150W
Color Wheel: 6 colors
LED: White
Light Source: 1-70W LED Light Source: 1-130W LED
Luminous Flux: Luminous Flux:
Life of LED : 50000H
Standard Aperture: Ø28mm / Ø24mm / Ø20mm (Optional: Ø30mm Max)
3
Size: 291X264X135mm
Gross Weight: 7.0Kg
Fig. 1
4
(3)The connection of DMX Signal Control Mode (See Fig. 2): Fig. 2
Fig. 3
DMX512 Console
Slave 2 Slave 3
Slave 1
(4)The connection of Master/Slave Control Mode (See Fig. 3):
Slave 1 Slave 2
Master
(5)Signal cable and connector (See Fig.4):
2
Signal cable should be 2X0.5mm audio cable.
PIN2: SIGNAL-
PIN3: SIGNAL+
PIN1: GND
3
1
2
Fig4
1
2
3
(2) Master/Slave Machines Setup Master/Slave mode:
Notice:
① If you need Master/Slaves to change color synchronously, please set all of slaves as“001”;
② If you need Master/Slaves to change color in sequence, please set first slave machine as
“006”, the second one as “011” and so on (add “5” one after another) .
MASTER
Slave
DMX Receiver
1.Hold and press the two buttons at
the same time for 3 seconds to
unlock the menu for setting up.
2. Hold and press the button “UP”,
at the same time to press the
button“DOWN” to switch the
menu.Then release both bottons.
3. Press either button of “UP” or
“DOWN” to choose the right
parameter.
4. After 60 seconds, the data will be
saved and the menu locked.
5. When the display is on, the dot
next to the third digit will flash
if there is any DMX signal coming
in.
1
12 preset programs(see attached list. When it
displays “P.XX”, press “UP/DOWN” to get into
this menu)
2
PS.1-PS.2 are audio control programs (when it
display “PS.X”, press “UP/DOWN” to get into
this menu)
3Color wheel speed setup: total 8 levels:1/2RPM,
1RPM,2RPM,3RPM,4RPM,5RPM,8RPM,12RPM
4Adjusting of brightness: total 8 levels: d.00,d.10,d.20,
d.35,d.50,d.70,d.85,d.99.(d.99.means100% brightness)
5r.on: Remote control is on,
r.oF: Remote control is off.
6DMX address,“001”-“508”are available
No.
STATUS MENU DESCRIPTION OF FUNCTIONS REMARKS
. .
. .
. .
. .
. .
FUSEPOWER
SWITCH
Fuse
Power switch
Power cable
DMX IN
DMX OUT
Aerial (optional)
DMX IN
DMX OUT
AERIA L
FUSEPOWER
SWITCH
DMX IN
DMX OUT
AERIA L
FUSEPOWER
SWITCH
DMX IN
DMX OUT
AERIA L
FUSEPOWER
SWITCH
DMX IN
DMX OUT
AERIA L
FUSEPOWER
SWITCH
DMX IN
DMX OUT
AERIA L
FUSEPOWER
SWITCH
DMX IN
DMX OUT
AERIA L
FUSEPOWER
SWITCH
DMX IN
DMX OUT
Model: LEI-8001DMX Model: MK-L150W DMX
CHAPTER 2 MK-L150W DMX
6100Lm(6000K) 11000Lm(6000K)
3. Light Engine Setup
There are three control modes for MK-Series DMX512 protocol Light Engine:
* DMX512 Signal Control Mode: DMX512 console is applied to deliver the DMX signal.
* Master/Slave Mode: One Light Engine is set as Master, while the rest light engines
are set as Slave. Master delivers control signal to slave so that all the machines run the
program synchronously.
* Audio Control Mode: Light engines are controlled by sound.
ENGINE
MK

5
Attached Table: Program and the Program number
6 colors skip & audio control
5 colors skip & audio control
Function
Pro. No.
PS.1
PS.2
Red
6 colors skip
5 colors skip
6 colors fade
6 colors skip & chase
6 colors fade & chase
Function
Pro. No.
No Light
White
Sky-B
Green
Yellow
Blue
Function
Pro. No.
P.00 P.06
P.01 P.07
P.02 P.08
P.03 P.09
P.04 P.1 0
P.05 P.1 1
Fig.5
RC-15
Wireless Remote Controller
3
6
9
2
5
8
0
SP
DIM
PRO
1
4
7
4. Wireless remote controller (See Fig.5):
Press the two buttons “UP” / “DOWN” besides the Display at the same time. When it
displays , press either button of “UP” / “DOWN” to show “ ”
(status of remote control). The remote function is on.
15-Key Remote Controller:
(1) Program Selection: Press“PRO”, then press the digit key on the
controller, “00”-“13”, to choose the desirable program, or you can
use “ ”,“ ” to select.
(2) Dimming: Press the key “DIM”, then press “ 0 ”-“ 7 ” to have the
desirable brightness, or you can use “ ”,“ ” to adjust.
(3) Speed of the twinkle wheel:Press the key “SP”, then press “0”-“7”
to adjust the speed, or you can use “ ”,“ ” to adjust.
“ ” or “ ”
Notice:
① Address code of slave (machines) are not adjustable under remote control status.
② When you are selecting the program, only double-digit numbers on the controller
are recognizable (e.g. 00, 01, 02...).
6
3. Commonly used installation method of fiber optic cable:
(1) Side Lighting Fiber Optic:(See Fig.3).
2.Installation of the end part of the Multi-String fiber optic:
(1) Drill holes on the installing board according to the design. Then insert the fiber optic
(2) Insert the finished Fiber Connector into the Fixing Flange and screw tightly the Screw.
string into holes and fix it with epoxy glue. Trim the end of the fiber string to be flush
with the board or at a required length. Fasten the other end of the fiber string to a
harness and insert the harness into PG Connector and Fiber Connector. Apply the
hot knife to cut fiber end flush with the Fiber Connector.
(See Fig.2).
1. Connecting the fiber optic with Light Engine:
Solid Core fiber optic(See Fig. 1):
(1) Cut the fiber to the specified length. The cross section should be vertical to the
fiber and keep clean and smooth.
(2) Peel off 50-100mm of the PVC jacket of the fiber optic cable (not necessary if
there is no PVC jacket). Be careful not to hurt the fiber optic.
(3) Unscrew the PG Connector and insert the fiber optic cable into the PG Connector
and Fiber Connector until the end of the cable is flush with the Fiber Connector.
Screw tightly the PG Connector.
(4) Insert the finished Fiber Connector into the Fixing Flange, screw tightly the Screw.
Single Lighting
End Plug
Light Engine
Side Glow
Fiber Optic
Single Set Double Lighting
Multi Sets Double Lighting
Fig.3
(2) End Lighting Fiber Optic:
(See Fig.4).
With End Piece
Fig.4
Fiber Optic
PG Connector Front Case
Fiber Connector
Fixing Flange
Fig. 1 Fig. 2
Chapter 3 Installation of Fiber Optic