CHAPTER 1 LEI-4361DMX
1
Safety Instruction
1. Make sure the Light Engine and Power Source have the same voltage;
2. Keep out of rain or moist area to avoid shock hazards;
3. Avoid to use at high ambient temperature ( >40℃);
LIGHT ENGINE
USER MANUAL
1. Technical Data
2. Installation dimension of light engine(see Fig.1):
Life of LED : 50000H
Standard aperture: Φ28mm/Φ24mm/Φ20mm (Optional:Φ30mm Max)
3
Size: 291×264×135mm
Gross Weight: 7.0Kg
Voltage: 90V~230V AC
Power: 150W
Color : RGBW
Light Source: 1-4X36W LED
(1) DMX 512 signal control mode:
Address Code Setup:
Press button “UP” and “DOWN” at the same time (maybe several times) until the digital
display shows “ ”, then press the button “UP” or “DOWN” to select the address
code.
001-505
DMX Channels: 8 Channels
CH1:Red (256 level) CH2:Green (256 level)
CH3:Blue (256 level) CH4:White
CH5:Speed (256 level) CH6:Dimmer (256 level)
CH7:Strobe/Program Speed CH8:Preset Program
Notice: 1 For CH8, Only “P01-P15” are available, “P016-P21” are not available;
2 When CH8 is not “0”, CH1~CH4 are not usable, CH7 is preset programs speed;
3 When CH8 is “0”, CH1~CH6 are usable, CH7 is strobe.
(2) Master/Slave mode: The setting of Master/Slave
Notice:
① If you need Master/Slaves to change color synchronously, please set all of slaves into”001”;
② If you need Master/Slaves to chase to change color, please set slaves into “009”,”017” and
so on (add “8” one after another) .
MASTER
Slave
DMX Receiver
1
22 preset programs(see attached list. When it
displays “P.XX”, press “UP/DOWN” to get into
this menu)
2
PS.1-PS.2 are audio control programs (when it
display “PS.X”, press “UP/DOWN” to get into
this menu)
3Color wheel speed setup: total 8 levels:1/2RPM,
1RPM,2RPM,3RPM,4RPM,5RPM,8RPM,12RPM
4Adjusting of brightness: total 8 levels: d.00,d.10,d.20,
d.35,d.50,d.70,d.85,d.99.(d.99.means100% brightness)
5r.on: Remote control is on,
r.oF: Remote control is off.
6DMX address,“001”-“505”are available
No.
STATUS MENU DESCRIPTION OF FUNCTIONS REMARKS
ps.1 -ps.2
s.00 -s.07
001-505
p.0 0-p.2 1 1.Press two buttons at the same
time to switch among menus.
2.If you haven't pressed the buttons
for a long time, the digital display
will be turned off, and the buttons
will be locked. Press“UP”or“DOWN”
to restart buttons operation(When
the power is on, you also need to
follow these steps), it will display
the last operation.
3.When slave machines receive the
DMX signal and the digital display
is on, the 3rd digital number of the
digital display will be flickering.
(3)The connection of DMX Signal Control Mode(See Fig. 2): Fig. 2
2
135
11 0
LED
SERIES
MENU
UP DOWN
MIC
AERI AL
275
291
26 4
Fixing Flange
Menu(UP,DOWN)
Fan
Fig. 1
FUSEPOWER
SWITCH
Fuse
Power switch
Power cable
DMX IN
DMX OUT
Aerial (optional)
DMX IN
DMX OUT
DMX512 Console
Slave 2 Slave 3
Slave 1
AERIA L
FUSEPOWER
SWITCH
DMX IN
DMX OUT
AERIA L
FUSEPOWER
SWITCH
DMX IN
DMX OUT
AERIA L
FUSEPOWER
SWITCH
DMX IN
DMX OUT
Welcome to use MK series of professional light engine. Please read the
manual carefully before using the light engine. If you have any questions
concerning the operation or maintenance, please contact your wholesaler.
3. Light Engine Setup
There are three control modes for MK-Series DMX512 protocol Light Engine:
* DMX512 Signal Control Mode: DMX512 Signal is received from a DMX512 controller.
* Master/Slave Mode: One Light Engine is set as Master, while the rest light engines
are set as Slave. Master sends control signal to slave so that all the machines run the
program synchronously.
* Audio Control Mode: Light engines are controlled by sound.
LIGHT ENGINE
MK
