WIKE CARGO TRIKE User manual

Tools needed to assemble Bike:
-High table or Stand
-Set of Allen/Hex wrenches
-Cable cutters
-12mm & 15mm wrenches
-Grease
-Presta compatible pump
Thank you for purchasing a WIKE CARGO TRIKE!
Contents
Safety……………………..…………………………..….3
Connecting the frame…….……………………….4
Wheel Assembly……………………………………..5
Box & Handle Bar……………………………………6
Seat post and Saddle………………………………7
Final pre-ride check…………………………………8

1. Handle bar & brake
lever
2. Gear shift
3. Brake lever
4. Box
5. Corner iron
6. Front reflector
7. Front frame (bottom
border)
8. Front wheel
9. Front brake
10. Fender
11. Bottom spacing pole
12. Rear frame
13. Chain cover and chain
14. Chain wheel and crank
15. Pedal
16. Rear wheel
17. Rear fender
18. Rear reflector
19. Seat post lock
20. Seat post
21. Saddle
2.

Safety
Before you ride your bike for the first time, familiarize yourself with the
location and operation of both brakes and steering attributes
Always check to make sure that all nuts are secured each time before
you ride in order to make sure the box is stable
Make sure the seat post bolt is securely fastened and that the seat post
does not slip before you ride
Never operate the bicycle if the frame, wheels or quick releases are
damaged
Proper maintenance and adjustment of the box bicycle will greatly
increase riding safety and performance
Always check your tires for proper inflation (25-40psi) that is indicated
on the tire’s sidewall
Reflectors alone are not adequate for riding at night. Front and rear
lighting systems are recommended to increase visibility
Always wear a helmet when riding the bicycle
The bicycle is designed for users of all sizes. However box bikes should
not be operated by children and young adults
Remember to comply with all bicycle safety laws and use common sense
especially in adverse weather condition
Wike takes no responsibility for accidents resulting from failure to
comply with all bicycle safety laws, careless driving or improper
maintenance of your box bicycle
3.

Connecting front frame and rear frame (Figure 1 & 2)
1. Pack grease into both bearings (grease not included)
2. After greasing bearings place them on either side of front frame
main pivot. Then insert pivot pin through bearing and front
frame.
3. Secure with washer and M18 cap nut
4. Align the two damper rods on each side of pivot and assembly.
Using washers, nuts and bolts provided (ADD loctite to bolts)
NOTE: Do NOT over tighten damper rods.
4.

Assemble the wheel sets
1. Assemble the fenders on the sides of the front frame as shown in
in Figure 3.
2. After screwing the disc rotor to the wheels. Place the front
wheels in the drop-outs (frame slots) and tighten axle bolts on
the two sides of front frame and tighten lock nut.
3. Put the disc brake over the rotor and fasten to the mounts. To
align have brake loosely fitted to mount, while brake is engaged
tighten bolts with spacers provided (Figure 4.)
4. Lateral adjustment of brake pads is achieved by turning the red
adjustment knob
5. Tube valves need a Presta compatible bicycle pump to inflate
5.

Assemble the box
1. Attach loosely with bolts the 4 corner irons to front frame
2. Assemble sides to corners
3. Tighten all bolts at completion of assembly of four sides
4. Place floor in box and bolt to front frame
Assemble handlebar (U-Type)
1. Assemble the handle bar as shown below in figure 6.
2. Adjust to preferred height and lock in place at sides.
3. Ensure brake and shifter cables do not interfere with steering
6.

Saddle and Pedal Assembly (Figure 8.)
1. Insert seat post into the seat and lock it with nut as shown in
figure 8.
2. Put other end of post into the frame seat tube with seat post
clamp and tighten to desired height
3. Grease and attach pedals to crank arms. Right hand thread on
Right crank and left hand thread on left crank. Pedals must be
tightened completely.
7.

11-Point Pre-Ride Check
1. Tires are inflated to 25-40 psi
2. All Axle bolts are tightened and wheels are secured
3. Dampers are secured and moving smoothly
4. Brakes are properly adjusted and function
5. Safety Straps in riders in box are secured and fastened
6. Pedals are tight and secure
7. Front Frame is secured to Rear Frame
8. Children have helmets on and are properly adjusted
9. All bolts and nuts are tightened securely
10. Chain has been well lubricated
11. Lights and bell function properly
Contact Us
FACTORY SHOWROOM
79 Regal Road, Unit 14
Guelph, Ontario
N1K 1B6
8.00am to 3.00pm M-F
wike.ca
US and Canada Toll Free: 866-
584-9452
Worldwide: 1-519-824-3869
Fax: [phone]
7 days a week 8.00am to
8.00pm EST
8.