Fisher-Price R6153 User manual

1
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Age: 1½ years - 5 years.
Weight Limit: 50 lbs. (23 kg).
Tools needed for assembly: Phillips Screwdriver,
Hammer and Scrap Block of Wood (all not included).
www.fisher-price.com
R6153

2
WARNING
To avoid serious injury:
• Adult supervision is required.
• Never use near cars and other motor vehicles,
near streets, steps, sloped driveways, hills,
roadways, alleys, swimming pools or other
bodies of water.
• Always wear shoes.
• Never allow more than one (1) rider.
Fasteners
All SHOWN ACTUAL SIZE
#8 x 3" Screw – 1
Cap Nut – 1*
Consumer Information
#10 x 3/4" Screw - 11
#8 x 3/4" Screw - 13
*Note: For your convenience, an extra cap nut is included.
Note: Tighten and loosen the screws with a Phillips screwdriver.
Do not over-tighten the screws.

3
Parts
Seat Pin
Seat
Handlebar
Handle Pin
Frame Cover
Handle Top
Handle Bottom
Base
2 Base/Handle Covers
Fork
Front Wheel Assembly
2 Fork Covers
4 Pedal Axle Covers
Straight Axle
2 Rear Wheels
Cap Nuts
2 Wheel Caps
Frame
Footrest
Note: The base/handle assembly can be attached to the trike in either the Ride-on Rocker (page 8) or Learn to Pedal (page 9) mode.
Parts not shown: Assembly Tool and Label.

4
Assembly
• Please save all packaging material until assembly is complete to
ensure that no parts are discarded.
• Please wipe each part with a clean, dry, cloth before assembling
this product.
This product contains small parts in its
unassembled state. Adult assembly is required.
Straight Axle
Rear Wheel Spoke
Side Down
• Turn the frame upside down.
• Insert the straight axle assembly through the holes in the rear of
the frame.
• Fit the wheel cap into the center of the wheel. Tap the wheel cap
with a hammer to secure it to the wheel.
Frame
Wheel Cap Hole
Hole
Rear Wheel
Straight Axle
• Slide a rear wheel (spoke side down) onto the straight axle.
Bottom View
CAUTION
• Fit the wheel cap into the center of the wheel. Tap the wheel cap
with a hammer to secure it to the wheel.
• Set the frame assembly aside.
Wheel Cap
• Turn the frame on its side with the exposed end of the straight
axle up.
• Place the assembled rear wheel on the scrap block of wood.
• Slide the other rear wheel (spoke side up) onto the end of the
straight axle.
• Place a cap nut on the end of the straight axle.
• Place the assembly tool over the cap nut and tap it with a hammer.
Gently pull the rear wheel up to be sure the cap nut is securely
attached to the straight axle.
Cap Nut
Straight Axle
Rear Wheel
Spoke Side Up
Assembled
Rear Wheel
Assembly Tool
Scrap Block
of Wood
1
2
3
4

5
Assembly
5
• Fit two pedal axle covers onto the pedal axle metal tabs. Make sure
the metal tabs fit into the slot in each pedal axle cover.
• While holding the pedal axle covers on the pedal axle, insert the
pedal axle into the hole in the center of the front wheel.
• Push the pedal axle covers into the center of the front wheel until
they are flush with the surface of the front wheel.
• Repeat this procedure with the other two pedal axle covers on the
other side of the front wheel assembly.
Pedal Axle Cover
Pedal Axle Cover
Metal Tab
Slot
Pedal Axle
• Place the front wheel assembly between the fork arms so that the
pedal axle fits into the groove at the bottom of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #10 x ¾" screws into the fork cover and tighten.
• Repeat this procedure to attach the other fork cover to the other
fork arm, using the #10 x ¾" screws.
Fork Cover
Fork Arms
Groove
Pedal Axle
Front Wheel Assembly
• Turn the frame upright.
• Insert the fork post up through the
hole in the frame neck. Make sure the fork is positioned so that
the fork covers face the rear wheels.
• Place the handlebar over the fork post and push it down onto the
frame. Make sure the handlebar is positioned so that the screw
hole faces the rear wheels and aligns with the screw hole in the
fork post.
• Insert the #8 x 3" screw through the hole in the handlebar and into
the fork post so that part of the screw (about ¾") is still visible.
Tighten the screw.
Handlebar
Frame Neck
Fork Covers
Fork Post
FIRST, insert the screw
so that ¾" is visible.
THEN, tighten the screw.
¾"
• Insert the knobbed end of the footrest
up through the opening in the underside,
center of the frame .
• Rotate the footrest ¼ turn .
• Slide the footrest toward the handlebar as far as it will go until
the top of the footrest is positioned over the opening’s
rectangular cut-out.
• Lower the knobbed end of the footrest into the rectangular cut-out
in the frame .
Frame Opening
Footrest
Knobbed End
Footrest
Knobbed End
Top View
7
8
6

6
Assembly
• Place the frame cover over the frame opening. Make sure the
holes in the frame cover align with the holes on the frame.
• Insert three #10 x ¾" screws into the frame cover and tighten.
Frame Cover
• Place the seat on the seat mount.
• Adjust the seat for your child’s comfort by aligning the hole in the
seat with one of the seat mount adjustment holes.
Seat Mount Adjustment Holes
Seat
Seat Mount
• While pushing down on the seat, insert the seat pin through the
hole in the seat and into a seat mount adjustment hole.
Seat Pin
• Fit the handle top and bottom to the end of the base, as shown.
Handle Top
Base
Handle Bottom
9
10
11
12
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052, U.S.A.
©2009 Mattel, Inc. All Rights Reserved. ® and TM designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO R6153pr-0920

7
• Insert 13 - #8 x ¾" screws into the handle top and tighten.
• Place the base/handle assembly on a flat surface so that the wheel
retainers are upright.
• Fit the trike onto the base/handle assembly so that the rear frame
rests in the grooves in the base and the front wheel fits between
the wheel retainers in the base/handle.
Wheel Retainers
Base/Handle
Grooves
Base/Handle
Handle Cover
Trike
Flared End
• Position the base/handle covers so that the flared end faces the
front of the trike.
• Fit the base/handle covers onto the trike rear frame near the
rear wheels.
• Insert two #10 x ¾" screws into each base/handle cover and tighten.
Assembly is now complete.
13
14
15
Assembly

8
Label Application
Handle
Place Center of
Label Here
Center of Label
• Before applying the label, wipe the surface of the handle with
a clean, dry cloth to remove any dust or oils.
• Remove the backing from the label.
• First, position the center of the label on the handle, as shown.
Then, smooth each end of the label outward to attach it to
the handle.
• For best results, avoid repositioning a label once it has been
applied to the handle.
Ride-on Rocker
• Insert the base/handle pin through one wheel retainer, a hole in
the front wheel and into the other wheel retainer.
• Push the handle pin to “snap” it into place. Pull on the handle
pin to be sure it is secure.
Wheel Retainer
Front Wheel
Wheel Retainer
Base/Handle Pin
IMPORTANT! Be sure to adjust the seat in the most forward
position for Ride-on Rocker mode.

9
Learn to Pedal Trike
• If you are converting from the ride-on rocker mode, remove the
handle pin from the wheel retainers and front wheel.
Wheel Retainer
Front Wheel
Wheel Retainer
Handle Pin
Base/Handle
• Insert the handle pin through one side of the base/handle,
through the holes in the back of the frame and out through
the hole in the other side of the base/handle. Make sure the
handle pin “snaps” into place.
• Pull on the handle pin to be sure it is secure.
Base/Handle
• Rotate the base/handle to the upright position.
Handle Pin
1
2
3

10
Pedal Trike
Base/Handle
• Rotate the base/handle down, under the trike, to the ride-on
rocker position.
Base/Handle
• If you are converting from the learn to pedal trike mode,
remove the handle pin from the base/handle and the back
of the frame.
Handle Pin
1
2
Base/Handle
Base/Handle Cover
• Remove the screws from the base/handle covers.
• Remove the base/handle covers.
• Remove the base/handle.
3

11
Pedal Trike Storage
Helpful Hint: To store for future use, position the handle covers
with the flared end upright and attach them to the handle using
the four screws. Insert the handle pin into either the holes in
the base/handle or through the holes in the retainers. Store the
base/handle in a safe place for future use as a ride-on rocker or
learn to pedal trike.
Handle Cover Handle Pin
Handle Cover
• Rotate the footrest up toward the rear wheels and snap it into the
recess in the underside of the frame.
Flared End
IMPORTANT! It is a good practice to start training
children very young regarding the importance of helmet use.
When children are older and riding bicycles and faster vehicles,
it is important that they use a helmet each and every time they
ride. For this reason, even while riding a tricycle, it is a good idea
to familiarize
your child with helmet use, so that it becomes a habit
for life. Choose a helmet that complies with requirements of the
applicable certifying agency for bicycle helmets.
4

12
Maintenance
• Check plastic parts regularly and if broken or cracked, dispose of
them properly.
• Check all fasteners regularly to be sure they are tight. If the
fasteners are not tight, tighten them as necessary.
• To clean this product, use a mild soap and water solution and
a clean cloth. Rinse clean with water to remove soap residue.