Wildix DUOLED-BT User manual

DUOLED-BT HEADSET USER GUIDE - ENGLISH!
PACKING LIST
1 x DuoLED-BT Headset
1 x Base Station
1 x USB Type-C to Type-C cable
1 x USB Type-A to Type-C adapter
1 x portable case
Note: It is required to install WIService on Windows and Headset Integration
component on macoS (Collaboration -> Settings -> Extensions) to use
DuoLED-BT.
Min. required versions of the components:
• WIService v 3.3.1 (Windows)
• Headset Integration v. 2.9.7 (macOS)
SAFETY INFORMATION
https://www.wildix.com/safety-information/
COMPATIBILITY
The Headset supports dual (multipoint) wireless connection,
which means it can be connected to two devices
simultaneously:
1. Via Base Station. Such connection provides full support of
LED user and call statuses and compatible with:
• Apple Mac, Windows PC
• WorkForce *
• WelcomeConsole *
*Temporary limitations:
•Full LED user statutes support on WorkForce, WelcomeConsole
will be available later
•The Headset cannot be connected to Vision/ SuperVision via
Base Station, the support will be available later
2. Via Bluetooth module embedded in the Headset itself. Such
connection doesn’t provide LED statutes support and
compatible with:
• Android, iOS apps
• Vision/ SuperVision
• W-AIR LifeSaver
• W-AIR Med
• W-AIR Office
POWER ON/ POWER OFF
Press Multi-function button for 3 seconds.
HEADSET AND BASE STATION OVERVIEW
CHARGING
1. Connect USB cable to the Base Station
2. Plug the cable into a device USB port!(use Type-A
adapter if needed)
3. Place DuoLED-BT into the Base Station
4. When charging, Headset status LED turns red
5. When charged, Headset status LED turns blue
Battery charging time
• Less than 60 minutes to charge 20%
• Less than 90 minutes to charge 50%
• Fully charged in less than 3,5 hours
CONNECT VIA THE BASE STATION
1. Connect USB cable to the Base Station
2. Plug the cable into a device USB port (use Type-A to
Type-C adapter if needed)
3. Turn the Headset on
4. The Headset Status LED starts blinking and the voice
prompt announces “Your Headset is connected”
5. For Collaboration, set “Wildix DuoLED-BT” as audio
device in Collaboration -> Settings -> Web phone
Note: The Headset and the Base Station are paired by default. If you
accidentally unpair them, proceed with the following steps to pair them
back:
•Press!and hold Pairing button on the Base Station for 3 seconds,
the Pairing LED indicator starts blinking with fast blue and red blinks
•Make sure the Headset is powered off. Press and hold the Multi-
function button for 3 seconds until you hear “Power on”. Keep
pressing for 3 seconds more until you hear “Pairing”
• The Headset Status LED starts blinking and the voice prompt
announces “Your Headset is connected”
CONNECT VIA BLUETOOTH EMBEDDED IN THE
HEADSET
1. Unplug the Base Station and turn the Headset!off
2. Activate Bluetooth on a device you want to connect
the Headset to
3. Press and hold the Multi-function button for 3
seconds until you hear “Power on”. Keep pressing for
3 seconds more until you hear “Pairing”
4. Search for DuoLED-BT in Bluetooth devices list on
your device and select it for pairing
5. The Headset Status LED starts blinking and the voice
prompt announces “Your Headset is connected”
Version 06/2021
Page of1 2

DUOLED-BT HEADSET USER GUIDE - ENGLISH!
LED INDICATORS
Status LED
Headset status LED
Base Station pairing LED
• Successful connection - long blue blinks
• Pairing - fast blue and red blinks
CHECK THE BATTERY LEVEL
On Windows you can check the battery level using WIService
tray:!
•Go to Quick Launch Toolbar -> right-click on!Wildix
Integration Service!icon and check the level of battery
(Low, Medium, High):
On macOS you can check the battery level using Headset
integration:
•Go to Menu Bar -> click on Headset Integration icon
and check the level of battery (Low, Medium, High):
ANSWER A CALL
Press Multi-function button to answer a call.
ADJUST VOLUME DURING A CALL/ RINGER VOLUME
Press Volume Up to increase the volume.
Press Volume Down to decrease the volume.
MUTE A MIC
Press Mute button during a call to put a call on hold / resume.
PUT ON PAUSE/ RESUME A CALL
Press!Multi-function!button for 2 seconds!during a call to put
a call on hold / resume.
END A CALL
Press Multi-function button to finish a call.
Version 06/2021
Page of2 2
User/ call
status
LED indication
Color
Available
Steady on
Green
Away
Yellow
DND/ in
conference
Violet
Outgoing call/
In call
Red
Hold
Fast short blinks
Status color + red
Missed call
Long blinks followed
by fast short blink
Status color + red
Incoming call
Fast short blinks
Red
Headset status
LED indication
Color
Power on
One blink
Blue
Power off
Red
Pairing mode
Fast short blinks
Blue
Pairing
successfully
Long blinks
Blue
Answer a call
Charging
Steady on
Red
Fully charged
Blue
Full guide online
www.wildix.com