WILDSYDE E-Cruisers The Beast User manual

1
Quick Start Guide
Wildsyde®Electric Bicycles
A quick introduction to your new Wildsyde ebike.
E-Cruisers
The Beast | Hunni Bunni | Shadow
PLEASE READ BEFORE USE
wildsyde.com
USA

2
A
B
CC
PLEASE READ ‘UNPACKING & ASSEMBLY INSTRUCTIONS’ IF E-BIKE REQUIRES ASSEMBLY.
Whilst your baery is charging, now is a good opportunity to read this Quick Start Guide carefully
and familiarize yourself with the controls and funcons. Use accompanied manual to help you.
Quick Start Guide
CONGRATULATIONS AND THANK YOU FOR BECOMING THE PROUD OWNER OF A UNIQUE
WILDSYDE® VINTAGE ELECTRIC CRUISER BICYCLE!
FULLY CHARGE
BATTERY BEFORE USE
Before your rst ride, charge baery for
6-8 hours unl charging indicator light
has turned green. Plug charging cable
into charging point underneath baery
tank (as shown) and connect to AC.
Or, remove baery and charge indoors
(see page 4). Then, prepare to ride unl
the baery discharges to 20% (1 bar)
on your rst ride then repeat charge/
discharge process for the next 3 rides to
opmize baery life and performance.
Applies to all Wildsyde E-Cruisers: The Beast, Hunni Bunni & Shadow.

3
12 3 4 5 8
7
12
1110
6
9
COCKPIT CONTROLS & FUNCTIONS
1. POWER/MODE
2. PEDAL ASSIST (PAS)
3. HEADLIGHT & TAILLIGHT
4. POWER GLIDE
5. BELL
6 & 7. BRAKES
8. LCD DISPLAY
9. USB CHARGING POINT
10 & 11. GEARS UP & DOWN
12. THROTTLE
1. POWER ON/OFF & TOGGLE MODE BUTTON
Your electric bike is started and switched o using the rubber embossed
MODE buon ‘M’, located on the le side of the handlebars, just
underneath the PAS/Lights/Power Glide arrow buons. Push this and
hold. The display will light up, indicang the ebike is now ON.
2. PEDAL ASSIST (PAS) UP/DOWN ARROW BUTTONS
Pedal Assist will automacally begin to work as soon as you start
pedaling. Push the UP arrow for more power and easier riding, the
DOWN arrow for less power and harder riding. PAS levels go from 1-5
and are displayed on the boom le of the LCD display.
3. HEADLIGHT & TAILLIGHT
Lights share the UP arrow buon with PAS. Push and HOLD the UP
arrow buon to switch on both headlight and taillight. The LCD display
will also illuminate. Push and hold the UP arrow again to switch both
lights o.
4. POWER GLIDE
Power Glide shares the DOWN arrow buon with PAS. Push and HOLD
the DOWN buon to engage the ‘Power Glide System.’ The bike will
move forward at up to 3mph for a few seconds to assist walking the
bike, when required.
A

4
5. BELL
A tradional vintage bell to warn pedestrians & trac of your approach.
6 & 7. BRAKES
All Wildsyde® E-Cruisers are equipped with hydraulic disc brakes and
motor inhibitors. When either front, rear or both brakes are applied, the
inhibitors automacally disable power to motor unl brakes release.
8. LCD DISPLAY
Includes Baery
Capacity Level, Pedal
Assist (PAS), Speed,
Trip/Total Distance and
Waage. See manual.
9. USB CHARGING PORT
Charge your phone or
other device whilst you
ride with a cable into the
USB port located at the
base of the LCD.
10 & 11. GEARS UP & DOWN
Change between 1-7 gears using the (+) buon and (–) lever on right side
of handlebars. Use lower gears at slower speeds and vice versa.
12. THROTTLE (CLASS 2)
Carefully press throle with thumb for instant acceleraon without
pedaling, making sure to release when you reach desired speed.
B. SEAT ADJUSTMENT
To adjust seat post to required height, undo seat
post clamp lever, slide the saddle up or down to
the desired height and then close the lever on
the seat clamp securely.
C. TIRE PRESSURES
Ensure res are inated to recommended 25-
45psi depending on rider weight, type of res
and terrain. Please refer to manual for more advice.
REMOVING THE BATTERY
Remove baery from its storage tank to charge
separately, and/or to avoid exposure to unnecessary excessive heat or
cold. To remove, simply unlock the baery tank with key(s) supplied,
unplug the two cables on baery, undo the velcro straps and carefully
remove. See manual for important informaon on baery care.
FOR DETAILED INFORMATION REFER TO MANUAL.
For quesons, please email in[email protected]om, or for urgent
assistance please call [phone].
POWER RUN-ON
It is normal for the bike to ‘run-on’ as power momentarily dissipates
from the electric motor aer pedaling. Be sure to ancipate this,
applying the brakes as necessary.
PLAN YOUR RIDE
Ensure to plan your rides that leaves enough baery power for
your return journey or to a desnaon where the bike can be
recharged. As a guide, a fully charged baery can provide a range
of 40-50 miles of smooth riding with PAS. Please refer to the
manual for more informaon.
ALWAYS WEAR A HELMET
Always wear an approved helmet when riding your bike, and follow
the helmet manufacturer’s instrucons for t, use and care.
B
C