Williams Sound BAT KT7 User manual

BAT KT7
Charger for Pocketalker 2.0
QUICK SETUP GUIDE
Product Description
The BAT KT7 is designed for charging the Williams AV
Pocketalker 2.0 when used with NiMH batteries. It comes
with adapters for various international and US outlets.
WARNING!
BEFORE CONNECTING THE CHARGER TO THE
POCKETALKER, MAKE SURE THE POCKETALKER
HAS NIMH RECHARGEABLE BATTERIES
INSTALLED (NOT ALKALINE).
MAN 200F

Safety Warnings
1. To prevent injury,never charge the unit in enclosed
spaces such as handbags, cases, or other closed
storage bags.
2. To prevent injury, unplug this device during lightning
storms, or when charging is complete and the device is
unused for long periods of time.
3. To prevent injury, use correct AC adapter for country of
use.
4. To prevent injury, use only the power supply provided by
Williams AV. Other power supplies may have similar
specifications, but may not be equivalent. Use of an
unapproved power supply may leave the device partially
or completely inoperable, and will void the warranty.
5. To prevent injury, protect the power cord from being
walked on or pinched, particularly at plugs, receptacles,
and near the power jack on the unit.
WARNING!
USE THIS CHARGER WITH NiMH RECHARGEABLE
BATTERIES ONLY - Williams AV P/N BAT 022 (or
equivalent) AAA size NiMH, 1.2 VDC Rechargeable
batteries).
Preparing the BAT KT7 charger for use
Choose the prong adapter for your country of use.
1. Slide the prong adapter onto to
the top of the power supply.
2. Continue sliding down until the
prong adapter clicks into a
locked position.

To remove the adapter:
1. Hold down the button in the
middle of the prong adapter.
2. While holding down the
button, slide the prong
adapter o of the device the
opposite direction as if you
were putting it on.
Charging the Pocketalker
It will take about 16 hours to fully charge the batteries.
1. Open the Pocketalker battery compartment and set the
battery switch to the NiMH position (Figure 1).
Figure 1: Battery Compartment
+
–
+–
A650
Battery type switch
AAA Batteries
(note polarity)
NiMH
Alkaline
2. Insert two AAA NiMH batteries. Be sure to follow correct
polarity (Figure 1). Do not use with alkaline batteries.
3. Connect the USB Cable using Figure 2:
a. Plug the USB “A” (larger rectangular) plug into the
USB port of the power supply. Do not force it. If it
doesn’t slide in easily, it could be upside down. If it is,
rotate it 180 degrees and try again.
b. Plug the USB Micro-B (smaller) connector into the
charging port on the Pocketalker.

4. Follow the instructions in the previous section
“Preparing the charger for use”.
5. Plug the power supply into an AC wall outlet (Figure 2).
6. The charging indicator on the Pocketalker will blink
slowly while the batteries are being charged, then stay
on when the batteries are fully charged.
Figure 2: BAT KT7 Charging Connection
A652
USB
Micro-B
Charging
Port
USB Micro-B
Plug (small)
USB A Plug
(large)
USB A
Port
PockeTalker 2.0 USB charging cord
Charging Indicator
Power Supply
US
Prongs
plug into
wall outlet
Warranty
The BAT KT7 is covered by a 90 day warranty.
Customer Service
If you experience diculty with your system, call Toll-Free
for Customer Assistance:
1-800-328-6190 (U.S.A.) or
[phone] (Outside the U.S.A.)
If it is necessary to return the system for service, your
Customer Service Representative will give you a Return
Authorization Number (RA) and shipping instructions.
[e-mail] / www.williamsav.com
800-843-3544 / INTL: [phone]
©2021 Williams AV LLC MAN 200F