Wilson Electronics SIGNALBOOST 811210 User manual

Amplifier Kit
Amplifier
Kit
Installation
G
u
ide
stallatio
stallat
Warning: This manual contains
important safety and operating information.
Please read and follow the instructions
in this manual. Failure to do so could be
hazardous and result in damage to your
amplifier.
!
SIGNALBOOST™
Mobile Amplifier Kit
with Phone Cradle
Contents:
Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1
How it Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2
Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3
Installing the Magnet-Mount · · · · · · · · · · · · · · · · · · · · · · 4
Installing the SIGNALBOOST™ Amplifier · · · · · · · · · · · 5
Installing the Cradle Plus · · · · · · · · · · · · · · · · · · · · · · · · 5
Attaching the Ultra-Slim Antenna · · · · · · · · · · · · · · · · · · 7
Powering Up the Amplifier · · · · · · · · · · · · · · · · · · · · · · · 8
Connecting the Earbud · · · · · · · · · · · · · · · · · · · · · · · · · 8
Warnings and Recommendations · · · · · · · · · · · · · · · · · 9
About Wilson Electronics · · · · · · · · · · · · · · · · · · · · · · · 10
Amplifier Specifications · · · · · · · · · · · · · · · · · · Back Cover
Wilson
®
Electronics, Inc.

1
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson’s 30-day money-back
guarantee. If for any reason the performance of any product is not acceptable,
simply return the product directly to the reseller with a dated proof of purchase.
1-Year Warranty
Wilson Electronics amplifiers are warranted for one (1) year against defects in
workmanship and / or materials. Warranty cases may be resolved by returning the
product directly to the reseller with a dated proof of purchase.
Amplifiers may also be returned directly to the manufacturer at the consumer’s
expense, with a dated proof of purchase and a Returned Material Authorization
(RMA) number supplied by Wilson Electronics. Wilson shall, at its option, either
repair or replace the product. Wilson Electronics will pay for delivery of the repaired
or replaced product back to the original consumer.
This warranty does not apply to any amplifiers determined by Wilson Electronics
to have been subjected to misuse, abuse, neglect, or mishandling that alters or
damages physical or electronic properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660.
Operation is subject to the following two conditions: (1) This device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of this device.
Disclaimer: The information provided by Wilson Electronics, Inc. is believed to
be complete and accurate. However, no responsibility is assumed by Wilson
Electronics, Inc. for any business or personal losses arising from its use, or for
any infringements of patents or other rights of third parties that may result from
its use.
Copyright © 2007 Wilson Electronics, Inc. All rights reserved.

2
Installation Instructions for the Following Wilson Amplifier Kit:
SIGNALBOOST™ Mobile Amplifier Kit with Phone Cradle
Model #811210 Part #811214
FCC ID: PWO819DA IC: 4726A-819DA
Patent Pending
The term “IC” before the radio certification number only signifies that
Industry Canada technical specifications were met.
Inside this Package
How it Works
Your new Wilson SignalBoost™ Mobile Amplifier Kit with Phone Cradle includes everything
you need to begin enjoying improved cellular performance in mobile applications. This kit
will amplify the signals to and from the cell phone that you place in its cradle.
The kit includes the magnet-mount outside antenna, one of Wilson’s most popular products,
which will collect the signal from the cell tower and send it through the cable to the
SignalBoost™ mobile amplifier. The amplifier’s state-of-the-art technology is designed to
increase your signal up to 10 times, and reduce disconnects and dropouts. The amplified
signal is sent to the Cell Phone Cradle Plus, Wilson’s versatile phone cradle, which has a
signal coupler built right in. Your cell phone then communicates with the improved signal.
When the cell phone transmits, the signal goes through the cradle coupler, is then boosted
by the amplifier and broadcast back to the cell tower through the outside antenna.
Most importantly, the Cradle Plus provides a convenient place to stow a cell phone and
allows the driver to keep both hands on the wheel while using the phone, greatly increasing
safety. This kit includes three mounting options for installing the cradle on the dash or
console of your vehicle.
SIGNALBOOST™
amplifier 12 V DC
power supply
Ultra-Slim
Antenna Magnet-Mount
Antenna
Cell Phone
Cradle Plus
Adhesive
Bracket Adhesive/Screw
Swivel Bracket
Earbud Air-vent
Bracket

3
Before Getting Started
This guide will help you properly install Wilson’s SignalBoost™ MobileAmplifier Kit with
Phone Cradle. It is important to read through all of the installation instructions for
this kit prior to installing any of the equipment. Read through this installation guide,
visualize where all of the parts will be installed, and do a soft installation before mounting
any equipment. If you do not understand the instructions in full, seek professional help, or
contact Wilson Technical Support at 866-294-1660.
Magnet-Mount
Antenna
Amplifier
Power Supply
Cell Phone
Cradle Plus

4
Installing the Wilson Magnet-Mount Antenna
To receive the best cell signal, select a location in the center of the vehicle’s roof that is 12
inches away from any other antennas and free of obstructions.
The antenna must be installed vertically.
Signal performance will be degraded if the
antenna is not vertical.
The antenna cable may be run through the
door to the amplifier.
The antenna cable is small enough to easily
tuck under the door seal or plastic molding.
For a more professional-looking installation,
the antenna cable may be run under the
door seal. Carefully pull down the door
seal. Run the cable through the seal
and push the seal back into place. This
prevents constant wear and tear on the
cable as the door opens and closes.
Carefully
Pull Down
Door Seal
Run Cable
Under
Seal
Tuck Cable
Under Seal
Warning: The antenna used with this
amplifier must have a separation distance of at
least 11 inches from all persons.
!

5
Installing the Wilson SIGNALBOOST™ Mobile Amplifier
Warning: Do not plug in the DC power
supply until the antenna and Cradle Plus
cables are attached to the amplifier.
!
Select a location to install the amplifier that
is away from excessive heat, direct sunlight
or moisture and that has proper ventilation.
Recommended installation locations for the
amplifier are:
• Under the seat
• Under the dash
Run the cable from the antenna and attach
it to the FME-Male connector labeled
“outside antenna” on the amplifier.
Attach the cable from the Cradle Plus to the
FME-Male connector on the amplifier.
Installing the Cradle Plus
Option 1 - Air Vent Bracket
Insert the two vent clips into the circular
hole in the bracket and slide them to each
end of the slot. The flat surface of the clips
should face upwards.
Slide the bracket clips into the chosen vent
until they snap into place. If necessary,
use a thin-bladed screwdriver to gently pry
the clips apart as they slide into the vent.
Position the moveable arm at the base of
the bracket to achieve the desired angle
and to provide additional stability for the
bracket.
Warning: Do not plug the amplifier
directly into the cell phone or cellular data card
using an antenna adapter. It will damage the
cell phone or cellular data card.
!

6
Option 2 - Adhesive Bracket
Clean the area where the bracket is to be
mounted with rubbing alcohol and a soft
cloth. Allow to dry.
Peel the backing to expose the adhesive
and press the bracket onto the desired
location in the vehicle. Note: be sure
the bracket is positioned vertically, not
horizontally.
Allow the adhesive to cure for 24 hours
before you attach the cradle.
Note: Once the cradle is attached, you can
adjust the angle of the adhesive bracket
by applying gentle pressure to the top or
bottom of the cradle.
Option 3 - Adhesive/Screw Swivel
Bracket
Clean the area where the bracket is to be
mounted with rubbing alcohol and a soft
cloth. Allow to dry.
For an adhesive mount, peel the backing
to expose the adhesive and press the
bracket onto the desired location in the
vehicle. Allow the adhesive to cure for 24
hours before you attach the cradle.
For a screw mount, use an ice pick or awl
to punch through the adhesive and expose
the four screw holes in the bracket. You
must provide the screws of an appropriate
size for your particular application. Using
the bracket as a template, mark the
locations for the screws as shown, drill pilot
holes and attach the bracket with screws.
Once the cradle is attached, you can
loosen the knurled wheel and swivel the
hook to the desired angle, then re-tighten
the wheel.
Attaching the Cradle
Once you have installed the mount in the desired location, attach the cradle by aligning
the rectangular hole on its back with the hook on the mount. Grasping the sides of the
cradle, slide it downward approximately ¼ inch into place.
For best mounting results and long-
term performance, we suggest that
you choose a flat smooth surface
like the console area of your vehicle
between the two front seats. If this is
not available in your vehicle, you may
mount the cradle on the front of the
dashboard.
If mounting the cradle on a sloped
area of the dashboard in your vehicle,
please note that gravity may affect
the adhesive over time. Use the
screw mount for a more permanent
attachment.

7
Attaching the Wilson Ultra-Slim Antenna
The Ultra-Slim must be placed directly
on the cell phone or cellular data card to
work properly. Attach the Ultra-Slim to the
cell phone or cellular data card with the
VELCRO®.
The Ultra-Slim cable is long enough to
reach the amplifier location. This allows for
ease and convenience of use.
To adjust the Ultra-Slim for the best signal,
go to a weak signal location where your
cell phone registers only 1-2 bars without
the Ultra-Slim connected. (Be sure the
amplifier is turned off when checking for
low signal.) Then, attach the Ultra-Slim to
the phone, power up the amplifier and you
should see a signal improvement of 2 or
more bars.
NOTE: Many phones take up to 20 seconds
to reset the bar indicator.
To maximize performance, attach the Ultra-
Slim as close as possible to the original
antenna on your cell phone or cellular data
card.
For cell phones with an internal antenna, place
the Ultra-Slim on the back of the phone near
the top. (Figure 1) NOTE: Certain phones,
such as the Motorola RAZR, have internal
antennas at the base, rather than the top, in
which case the Ultra Slim should be attached
at the bottom rear of the phone.
For cell phones with an external antenna,
place the Ultra Slim directly below the phone’s
original antenna. (Figure 2)
If you have any questions as to the location
of the antenna on your phone, call Wilson
Technical Support at 866-294-1660, 435-673-
5021 or visit www.wilsonelectronics.com.
Amplifier Ultra-Slim Antenna
Figure 1 Figure 2
To Amplifier
Cellular data card

8
Powering up the Amplifier
Make sure both the outside antenna and
Cradle Plus (or universal connector)
cables are connected before powering up
the amplifier.
Connect the power cable from the DC
power supply to the amplifier input marked
“Power” and insert the large end into DC
power socket (the cigarette lighter outlet).
The amplifier may remain on all the time. However, leaving the amplifier on in a vehicle
when it is not running can discharge the battery in a day or two.
A good option is to power the amplifier through the ignition switch so the amplifier is turned
on and off with the vehicle.
Carefully insert the power cable.
IMPORTANT: Do not power up the
amplifier unless the antenna and Cradle
Plus cables are attached to the amplifier.
Warning: Use only Wilson power
supply units. Use of a non-Wilson
product may damage your equipment.
!
12 V DC power supply (included)
AC/DC power supply (not included)
Connecting the Earbud
Plug the earbud into your cell phone and carefully place the earbud’s speaker into your ear.

9
Warnings and Recommendations
Warning: Do not plug the amplifier directly into the cell phone or cellular
data card using an antenna adapter. It will damage the cell
phone or cellular data card.
Warning: Do not plug in the power supply until the outside antenna and
Cradle Plus (or Ultra-Slim Antenna) cables are attached to the
amplifier.
Warning: The antenna must be installed with a separation of at least
11 inches from nearby persons and must not be located or
operating in conjunction with any other antenna or amplifier.
Use of this amplifier with an antenna gain higher than 6.12 dBi
is in violation of FCC regulations for which the offender is fully
liable. All Wilson mobile antennas are 6.12 dBi or less.
Recommended amplifier installation locations for a vehicle are:
• Under the seat
• Under the dash
Power the amplifier through the ignition switch so the amplifier is turned on and
off with the vehicle.
For best mounting results and long-term performance of the Cradle Plus, we
suggest that you choose a flat smooth surface like the console area of your
vehicle between the two front seats. If this is not available in your vehicle, you
may mount the cradle on the front of the dashboard.
If mounting the cradle on a sloped area of the dashboard in your vehicle, please
note that gravity may affect the adhesive over time. Use the screw mount for a
more permanent attachment.
9