Wilson Electronics WILSONPRO ENTERPRISE 4300 User manual

ENTERPRISE
4300/4300R
A Wilson Electronics Brand
wilsonpro.com 866.294.1660
Installation Guide
In-Building Cell Signal Amplifier
With Frequency-Specific Outside Antenna Ports and
LTE Connected Remote Monitoring

Package Contents 1
About The Enterprise 4300 & 4300R 2
Key Features 4
Post Install Setup 5
Menu System 6
Safety Guidelines 16
Specifications 18
Warranty 19
Index

ENTERPRISE 4300 & 4300R IN-BUILDING CELL SIGNAL AMPLIFIER 1
Enterprise 4300 Amplifier
Wide Band Directional Antenna (qty. 1)
Dome Antenna (qty. 4)
Enterprise 4300R Rack Mount Amplifier
Wide Band Directional Antenna (qty. 1)
Dome Antenna (qty. 4)
100 ft. Wilson400 Cable (qty. 5)
50 Ohm Lightning Surge Protector (qty. 1)
2 ft. Wilson400 Cable (qty. 1)
100 ft. Wilson400 Cable (qty. 5)
50 Ohm Lightning Surge Protector (qty. 1)
2 ft. Wilson400 Cable (qty. 1)
Enterprise 4300 SKU 460152 & 460152F
Enterprise 4300R SKU 460153 & 460153F
Package Contents

IN-BUILDING CELL SIGNAL AMPLIFIER ENTERPRISE 4300 & 4300R
2
Frequency-specific “split mode” option, facilitating
separate outdoor antennas for dierent bands,
resulting in improved indoor coverage.
Remote system monitoring. Connects to WilsonPro
Cloud service via internal, pre-activated LTE
modem.
High max downlink power (+17 dBm) for up to
100,000 sq ft coverage with a strong “5 bar”
outside signal.
High max uplink power (up to +26 dBm): will reach
far-away cell tower.
In-Building Cell Signal Amplifier Systems
Enterprise 4300 & 4300R

ENTERPRISE 4300 & 4300R IN-BUILDING CELL SIGNAL AMPLIFIER 3
The Enterprise 4300 & 4300R cell signal amplifier systems provide significantly
enhanced 4G LTE and 3G voice and data coverage inside buildings where cell signals
may not otherwise penetrate. Installation of a Enterprise 4300 & 4300R cell signal
amplifier system results in fewer dropped calls, improved voice quality, uninterrupted
texts, and faster data speeds—along with better audio and video streaming.
The Enterprise 4300 & 4300R cell signal amplifier systems also incorporates
Wilson Electronics’ state-of-the-art XDR (eXtended Dynamic Range) technology
that prevents signal overload conditions which can, in accordance with regulations,
force the amplifier to shut down. When the Enterprise 4300 & 4300R cell signal
amplifier systems sense that any incoming cell signal is too strong and threatens to
overload the system, XDR automatically reduces amplifier gain to compensate while
maintaining signal coverage throughout the building. The Enterprise 4300 & 4300R
cell signal amplifier systems incorporate an easy-to-use color LCD touch screen, and
both antenna ports are located on same side of the unit for simple installation. Like
all WilsonPro cell signal boosters, the Enterprise 4300 & 4300R cell signal amplifier
systems are universal: they work for all cellular devices, all services and all U.S. and
Canada cell phone carriers.

IN-BUILDING CELL SIGNAL AMPLIFIER ENTERPRISE 4300 & 4300R
4
Extended Dynamic Range (XDR) for continuous connectivity:
XDR lets the Enterprise 4300 & 4300R systems work with an
incoming signal and never shuts down due to a strong
outside signal.
Simple Wall-Mount & Rack Mount Installation: An indoor and
outdoor port(s) are located on top of the amplifier for easy antenna
connections, while an exposed mounting flange on each amplifier
provides for simple installation.
Onboard Software for Better Control: The amplifier is
automatically controlled with onboard software, ensuring great
connectivity throughout large spaces and multi-story buildings.
The amplifier will adjust its gain level up or down as required by
the conditions of the immediate signal environment.
Color LCD Touch Screen: The Enterprise 4300 & 4300R
systems utilize a color LCD touch screen, for assessing amplifier
performance, making adjustments to the outside antenna.
4
Key
Features

ENTERPRISE 4300 & 4300R IN-BUILDING CELL SIGNAL AMPLIFIER 5
The Enterprise 4300 & 4300R systems are designed with advanced internal
programming, which allows it to automatically adjust for a variety of conditions, while still
amplifying weak signals.
THE SERVER PORT ANTENNAS WILL BE USED TO PROVIDE COVERAGE TO
DIFFERENT AREAS WITHIN A BUILDING AND WILL BE INSTALLED WITH A
MINIMUM OF 10 METERS SEPARATION BETWEEN SERVER PORT ANTENNAS.
Post Install
Setup

IN-BUILDING CELL SIGNAL AMPLIFIER ENTERPRISE 4300 & 4300R
6
The Enterprise 4300 & 4300R takes about 8 seconds to boot up. Once boot up is
complete, the home screen will appear, showing the amplification and status of each
port and band.
A solid green light indicates that a band
is operating correctly with maximum
allowable gain.
A solid yellow light indicates band gain
reduction because of an oscillation
condition. Reposition antennas (increase
separation between indoor and outdoor
antennas, and point in opposite directions)
and then reboot (turn the unit o & on)
the Enterprise 4300 & 4300R system
to reactivate the band and maximize
performance. When adequate separation
is achieved, the yellow lights will return
to green upon reboot.
Note: when the light is yellow, the band
is operational; however, performance
is reduced.
Home Screen
Start Up Screen
Band Menu Color Description
Menu System

ENTERPRISE 4300 & 4300R IN-BUILDING CELL SIGNAL AMPLIFIER 7
A red light indicates a band has
been shut down because of a severe
oscillation condition or repeated
oscillation. Reposition antennas
(increase separation between indoor and
outdoor antennas, and point in opposite
directions) and then reboot (turn the unit
o & on) the Enterprise 4300 & 4300R
system to reactivate the band and
maximize performance. When adequate
separation is achieved, the red light(s)
will return to green upon reboot.
Gray indicates band has been disabled.
(MENU SYSTEM cont.)

IN-BUILDING CELL SIGNAL AMPLIFIER ENTERPRISE 4300 & 4300R
8
There are 5 Settings Screens represented by “tabs”. Tap the tab heading to view
each Settings Screen.
Note: Bands and Ports are disabled or enabled from the Cloud or Local Configuration Utility only.
Tap ‘Settings Icon’ to view the Settings Screen.
Settings Screen

ENTERPRISE 4300 & 4300R IN-BUILDING CELL SIGNAL AMPLIFIER 9
Ethernet Settings Tab
Modem Settings Tab
(MENU SYSTEM - SETTINGS SCREEN cont.)

IN-BUILDING CELL SIGNAL AMPLIFIER ENTERPRISE 4300 & 4300R
10
Cloud Communication Settings Tab
Antenna Settings Tab
Note: The Reset Local Comm button (button name will likely change) is used in case the user
has configured the amplifier such that the Local Configuration Utility is not accessible, e.g.,
if the communication preferences are set to “LTE Only”. The “reset” function will change the
communication preferences to “LTE Preferred w/Ethernet Backup”. It will also reset the login
credentials for the Location Configuration Utility to factory defaults.
Common Mode is configured from the Local Configuration Utility and should be set when
using a single Donor/Outside Antenna.
(MENU SYSTEM - SETTINGS SCREEN cont.)

ENTERPRISE 4300 & 4300R IN-BUILDING CELL SIGNAL AMPLIFIER 11
Split Mode Configuration
Split Mode is configured from the Local Configuration Utility and should be sent when
using separate Donor/Outside Antennas for Band 4/25, Band 5, and Band 12/13.
To go back to the Home Screen top on the Home Icon (in the lower right corner).
(MENU SYSTEM - SETTINGS SCREEN cont.)

IN-BUILDING CELL SIGNAL AMPLIFIER ENTERPRISE 4300 & 4300R
12
To view specific band information (such as the strength of the received uplink & down-
link signal, outside signal strength, and amplifier gain status) tap the desired band on the
home screen.
Oscillation Example
Band Status Screens

ENTERPRISE 4300 & 4300R IN-BUILDING CELL SIGNAL AMPLIFIER 13
Shutdown Example
(MENU SYSTEM - SETTINGS SCREEN cont.)

IN-BUILDING CELL SIGNAL AMPLIFIER ENTERPRISE 4300 & 4300R
14
Ethernet Status Icon
The three icons in the upper right provide status related to the Ethernet connection,
Cloud connection, and USB device (if inserted).
Cloud Status
Connectivity Status Screens

ENTERPRISE 4300 & 4300R IN-BUILDING CELL SIGNAL AMPLIFIER 15
(MENU SYSTEM - CONNECTIVITY STATUS SCREENS cont.)
USB Status

IN-BUILDING CELL SIGNAL AMPLIFIER ENTERPRISE 4300 & 4300R
16
Warnings
To uphold compliance with network protection standards, all active cellular devices must maintain at
least 6 feet of separation distance from Panel and Dome antennas.
Use only the power supply provided in this package. Use of a non-Wilson Electronics product may
damage your equipment.
The Signal Amplifier unit is designed for use in an indoor, temperature-controlled environment
(operating temperature ranges from -40°C to 60°C – -40°F to 140°F). It is not intended for use in attics
or similar locations subject to temperatures in excess of that range.
RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all persons.
AWS Warning: The Outside Antenna must be installed no higher than 10 meters (31’9”) above ground.
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have
your provider’s consent. Most wireless providers consent to the use of signal boosters.
Some providers may not consent to the use of this device on their network. If you are
unsure, contact your provider.
In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-05.
You MUST operate this device with approved antennas and cables as specified by the
manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from (i.e., MUST NOT
be installed within 20 cm of) any person.
You MUST cease operating this device immediately if requested by the FCC (or ISED in
Canada) or licensed wireless service provider.
WARNING. E911 location information may not be provided or may be inaccurate for calls
served by using this device.
This device may be operated ONLY in a fixed location (i.e..may operate in a fixed location
only) for in-building use.
FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR
WIRELESS PROVIDER, PLEASE SEE BELOW:
Sprint: http://www.sprint.com/legal/fcc_boosters.html
T-Mobile/MetroPCS: https://support.t-mobile.com/docs/DOC-9827
Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html
AT&T: https://securec45.securewebsession.com/attsignalbooster.com/
U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp
FOR MORE INFORMATION ON REQUIREMENTS SET OUT IN ISED CPC-2-1-05,
SEE BELOW:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html
Safety Guidelines

ENTERPRISE 4300 & 4300R IN-BUILDING CELL SIGNAL AMPLIFIER 17
The following accessories are certified by the FCC to be used with the
ENTERPRISE 4300/4300R.
314411
Wide Band Directional Antenna (Outside Antenna)
952300
100 ft. Wilson400 Cable (for Outside Antenna)
304412
Dome Antenna (Inside antennas)
952300
100 ft. Wilson400 Cable (for Inside Antennas)
859902
50 Ohm Lightning Surge Protector
952302
2 ft. Wilson400 Cable
Antenna Kit Options

IN-BUILDING CELL SIGNAL AMPLIFIER ENTERPRISE 4300 & 4300R
18
Model Number 460152 / 460152F / 460153 / 460153F
FCC ID PWO460052 / PWO460052 / PWO460053 / PWO460053
IC ID 4726A-460052 / 4726A-460052 / 4726A-460053 / 4726A-460053
Connectors N-Connectors
Antenna Impedance 50 Ohms
Frequency 698-716 MHz, 729-756 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz
Power output for single cell
phone (Uplink) dBm
700MHz Band12/17 700MHz Band13 800MHz 1700MHz 1900MHz
22.9 23.1 24.6 22.8 25.5
Power output for single cell
phone (Downlink) dBm
700MHz Band12/17 700MHz Band13 800MHz 2100MHz 1900MHz
16.9 16.7 16.8 16.6 16.6
Noise Figure 5 dB nominal
Isolation > 90 dB
Power Requirements 120V AC 0.5A
The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met.
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without
factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order
to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a
signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster
will automatically turn the power o on that band. For a detected oscillation the Signal Booster will automatically resume normal
operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut o until the
Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity
are maintained by the Signal Booster’s microprocessor.
This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes
or modifications not expressly approved by weBoost could void the authority to operate this equipment.
Specifications
NEED HELP? support.wilsonpro.com 866.294.1660